ImicTek IMIC-ME20 User manual

Digital Thermometer-Hygrometer
User’s Manual
1. Introduction
Thank you for purchasing our Digital Thermometer-Hygrometer. Please
take a few minutes to browse through this user manual before you
begin to operate the meter to ensure that you are fully familiarized with
how best to operate the meter as accurately and safely as possible.
This product is for indoor use, only. It uses a high-speed microprocessor
and a high-precision digital sensor, which can quickly and accurately
measure the current environmental temperature and humidity. It is
useful in homes, offices, warehouses, laboratories, greenhouses, etc.
2. Specifications
Name：Digital Thermometer-Hygrometer
Model：IMIC-ME20
Standard：QB/WSDJ ME2X-2019
Temperature：-10~60.0℃(14~140℉)，Resolution0.1℃，Accuracy±0.3℃
Humidity：0~99%RH，Resolution1%RH，Accuracy±3%RH
Calibration Range:±9.9℉/±9%RH
Sample rate：default 5 seconds，Adjustable range 1~60seconds
Dimension：80 x 80 x 13mm
Weight：62g
Battery：CR2032，DC3V

Humidity<30% or >60%
30% <Humidity<60%
Temp.<68 ºF 68 ºF ≤Temp.≤78.8 ºF Temp.>78.8 ºF
-- Comfortable --Uncomfortable
6
5
4
1
2
3
Temperature display
1
Bluetooth indicator
2
Low power indicator
3
4
Humidity and Units
Temperature units
6
Comfort level indicator
5
3. Panel information
Comfort Level Indicator
Low power indicator
When the battery voltage drops below proper operation range, the symbol will
appear on the LCD display and the battery will need to be replaced.

Note that the sample rate will affect the battery life, the shorter the cycle, the
shorter the battery life. The following table is for reference only:
Sampling time
Battery life
1s
About 90 days
5s
About 1 year
10s
About 1.5 year
c. Select Degrees Fahrenheit or Celsius
Press the button to select degrees in Fahrenheit (ºF) or Celsius (ºC).
d. Adjust Sampling Rate
The default sample rate is 5 seconds after each power-on. If you need to adjust
the increment, press SET button for 5 seconds to enter the setting mode. Press
the button to choose the sampling timebetween 1 - 60 seconds. Set the meter
for 10 seconds to save and exit automatically.

Face lcon Display Mode
To remove,or display, comfort level indicator(face icon)single press“SET”button.
How to Calibrate:
(Note:Calibrations will be reset when battery is removed.)
a. To access calibration mode, press both “SET”and “△” buttons simultaneously
for at least 5 seconds, until display shows calibration page. Then release
buttons.
b. Press“SET” to switch between C/F, temperature and humidity settings.
c. Press “△” to change or calibrate the data value higher or lower than the
actual reading.
d. New settings are saved automatically after 10 seconds. To reset system to
manufacturer’s settings, remove and replace battery.
77.0

6. Precautions and notes
a. Do not use in high temperature and humidity environment for an extended
period of time.
b. Avoid prolonged exposure to volatile chemicals.
c. Please use gentle detergent to clean product’s surface if needed.
d. Upon initial use, allow for a 30 minute lag time for monitor to register the
correct data.
7.Warranty instructions
Warranty Ordinance
The after-sales service of this Thermo-hygrometer must be in strict accordance
with the Amazon warranty.
Non-warranty Ordinance
1.Non-authorizedmaintainance,dropding,liquid contamination, etc.
2.Expiration of warranty.
3.Damaged by any major force event.
4.Situations not in “Fault Table.”
5.Situations caused by misuse.