Indeco IDS150 User manual

• IDS150 Power/Control Unit
IDP150 Desoldering Gun•
Desoldering Bit •
• Heavy Duty Support Rack
Cleaning Sponge•
Operating Manual•
• Input Supply
Heating Power•
Temperature Range •
• Vacuum Pressure
Tip to Ground Potential•
Tip to Ground Resistance •
: 230 VAC, 50Hz
: 150 Watt
: 300 C ~ 480 C° °
: 650mm Hg
: <2mV
: <2 Ohm
Specifications Scope of Supply
High Power (150W) Thru Hole Digital Desoldering Station Model IDS150
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing
patents. We accept no liability of whatsoever for any fa ults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
1
reliable & caring since 1976
Warranty is 12 months from the date of invoice.
It excludes all consumable parts as Sensor etc. and any mechanically damaged parts.
on-site services can be provided at extra charges
if pre-paid by customer in advance
Website: www.indeonline.in Email: [e-mail] & @indeonline.inPhones: 9316134502 & 9815600745
150 Watt High Power
for multilayer PCBs &
heavy grounded joints
Lightweight
Desoldering Gun
Desoldering
Nozzle
Heavy Duty
Stable Stand
Digital LCD display
of temperature
and other menu
settings
Burn Proof Cord
& Vacuum Pipe
in-built powerful
Vacuum Pump
Cleaning
Sponge
Desoldering
Gun Holder
3-Channels to store
3 different favorite
temperatures
UP/DOWN Button
for parameter
settings
Salient Features
● Power/Control unit has following
in-built features:
- Password protection
- In-built temperature calibration
- Sleep Timer & Standby Timer
- Error message indication
● Reliable heating element does not
require frequent changing
● Low running cost due to low priced
long life Desoldering Nozzles
Melting solder After the set temperature is stable,
use the Desoldering Nozzle to melt the solder.
Features
How to use Desoldering Gun
Solder removal
Observe that all the
solder of the pin has
been melted by rotating
the nozzle against the
pin. If the pin moves
freely, it means all the solder is melted. Now
press the red switch on the handle to suck the
molten solder.
Note: Do not rotate the pins vigorously and with
pressure. It can damage the PCB pads. If the pin
does not move easily, then apply fresh solder on
the tip of nozzle and then melt the solder of the
pin to suck the molten solder.
CH1, CH2 & CH3:
These channels are used to store 3 different frequently used temperatures.
Stored temperatures can be recalled just by pressing respective CH button.
Password Protection:
Password is provided for supervisory control. Once the password is applied
then no one can change the set parameters without entering the password.
Sleep Time Setting
Sleep mode is prolongs the life of Heating Element and Desoldering Nozzles.
It can be programmed from 01 ~ 20 minutes. 00 indicates no sleep. The
system enters in sleep mode if it is not used for set time after putting on the
stand. In sleep mode display shows “---”
Standby Time Setting
Standby time can be programmed from 01 ~ 40 minutes. 00 indicated no
standby. Standby timer starts once the unit enters the sleep mode. When
the system is in standby mode display will shows “OFF”
Temperature Calibration
This system has in-built calibration feature to meet ISO requirements. This
is recommended every time when the heating element or nozzle is replaced.

High Power (150W) Thru Hole Digital Desoldering Station Model IDS150
While the information contained herein in, has been carefully compiled to the best of our knowledge, nothing is intended as representation and warranty on our part; and no statement shall be construed as recommendation to infringe any of existing
patents. We accept no liability of whatsoever for any fa ults and errors in the information contained herein. Contents of this catalogue and specifications of the products, are subject to change without notice due to continuous improvements.
2
reliable & caring since 1976
Warranty is 12 months from the date of invoice.
It excludes all consumable parts as Sensor etc. and any mechanically damaged parts.
on-site services can be provided at extra charges
if pre-paid by customer in advance
Website: www.indeonline.in Email: [e-mail] & @indeonline.inPhones: 9316134502 & 9815600745
Description RemarksActual Picture
Assured availability, normally ex-stock, of Spare Parts for Desoldering Station
Desoldering Nozzles for IDS150 Desoldering Station
Description Actual Photo Part NumberInner Dia (mm) Outer Dia (mm) Dimensional Diagram
A10073.01.6
A1006
Nozzle for
regular
desoldering
3.01.3
Nozzle for
heavy
connector
desoldering
Heating Element Replace if display
shows H-E or S-E
Barrel & Nut Assembly Whenever required
Whenever requiredIDP150 Desoldering Gun
Spring Filter
Whenever requiredFilter Pipe
Whenever required
Ceramic Filter
Filter Pipe Assembly Whenever required
Packing Whenever required
Whenever required