Inder Power 392A User manual

READ INSTRUCTION MANUAL
CAREFULLY BEFORE USE
Instruction Manual
Model 392A
PPR PIPE WELDING MACHINE WITH CLAMPING
Page # 1 - M:392A
PPR PEPE WELDING MACHINE WITH CLAMPING
SAFETY INSTRUCTIONS
WARNING : When using tools, the following safety instructions must be observed to
reduce the risk of personal injury and property damage.
Please read and observe the following instructions before use.
1. Keep work area clean : An untidy and cluttered work area increases the risk of accidents
2. Use eye protection : Always use safety glasses or goggles. A face mask should also be worn
when dust is generated.
3. Wear suitable work clothes : Don't wear loose fitting clothes or jewellery. They can be caught
in moving parts and may cause injury. For outdoor work rubber gloves and non-stick footwear
are advised. Wear a protective hair net to contain long hair.
4. Guard against electric shock : Avoid any body contact with grounded surfaces e.g. bars,
radiators, stoves, and refrigerator enclosures.
5. Keep children away : Children should be kept away from the work area. Do not permit them to
handle the tool or tool cable.
6. Secure the work pieces : Use clamps or a vice to hold work. This will free up both hands to
operate the tool, which is safer.
7. Don't overreach when working : Keep a balanced footing at all times.Avoid abnormal stances
and awkward body positioning.
8. Do not overload or force tools : Tools operate better in the specified performance ranges.
Forcing the tool may cause motor damage.
9. Check for damage : Before further use always check the protection guards carefully to ensure
proper operation and performance. Check for alignment of moving parts, binding of moving
parts, breakage of parts, mountings and any other condition that may effect the tools operation.
An authorised service dealer should properly repair all damaged parts unless otherwise
indicated elsewhere in the instruction manual. Do not use the tool if the switch does not turn it on
and off.
10. Pull out power plug : When changing accessories or when the tool is not in use.
11. Avoid unintentional starting : Do not carry tools by the switch. Always check that the switch is
in the off position before connecting to power source.
12. Don't abuse power cable : Never carry the tool by the power cable. Do not use the power cable
to pull the plug out of the power point. The cable should also be protected from heat, oil and
sharp objects.
13. Storage : When not in use your power tools should be stored in a dry area, which is not
accessible to children.
14. Stay alert : Do not use the tool when you are tired. Use common sense and watch what you are
doing.
15. Remove keys and spanners : Do not forget to remove any adjustment keys, spanners and
wrenches before switching on the tool.
16. Voltage warning : Before connecting the tool to the power source ensure the voltage specified
on the nameplate is the same as the voltage supply. A power source with voltage greater than
specified on the tool can cause serious injury and damage to the tool. Using a power source with
voltage less than the tool rating can cause damage to the motor. Do not plug in tool if you are in
doubt.
17. Recommended use : Please note the use of tools other than those described in instruction
manuals or in the product catalogues can result in a risk of personal injury.
SINCE 1958
POWER
Page # 4 - M:392A

WARRANTY CERTIFICATE
Product : PPR PIPE WELDING MACHINE WITH CLAMPING
Identification : Type Designation : P-392A
LIMITED ONE YEAR WARRANTY AGAINST MANUFACTURING DEFECT.
Makes every effort to assure that its PPR PIPE WELDING MACHINE
WITH CLAMPING meet high quality and durability standards and warrants to the original
purchaser that the product is free from defects in material and workmanship for the period
of one year form the date of purchase. This warranty does not apply to damage due directly
or indirectly to misuse, abuse, negligence or accidental repairs or alteration outside our
facilities, or to lack or indignance. We shall in no event be liable for death, injuries to person
or property or for incidental contingent, special or consequential damages arising from the
use of our product. Some states don't allow the exclusion or limitation of incidental or
consequential dames, so the above limitation of exclusion may not apply to you.
To take advantages of this warranty, the product or part must be returned to us with
transportation charges pre-paid. Proof of purchase date and an explanation of the
complaint must accompany the merchandise. If our inspection very the defect, we will
either repair or replace the product all elecrole or we may elect to refund the purchase price
if we cannot readily and quickly provide you with replacement. We well return repaired
products all our expense, but if we determine there is no defect, or that the defect resulted
from caused no within the scope of our warranty, then you must bear the cost of returning
the product.
This warranty gives you specific legal right and you may also have other rights which vary
from state to state.
691257
4
o
N*
Accredited
by the RvA
SINCE 1958
POWER
Page # 2 - M:392A
Prod. No. 392A
Size (mm) 63 - 160
Spec. 220V/50Hz., 270°C, 1750W
No. of Dies 63, 75, 90, 110, 160
Page # 3 - M:392A
PPR PIPE WELDING MACHINE WITH CLAMPING INSTRUCTION
MANUAL
FEATURE : It is electric portable device which is used to weld PPR, Pipes
Size 63-16mm at sight during installation with joints.
I. Safety Requirements
1. Fix the Pipe to the clamp at left end, leave certain length according to actual situation and fix the fitting to the
active stand at right end.
2. Choose the welded head of same size as the pipe you need to weld, put the coneave welded head to the left side
of the heated board and protruding one to right then fix up the screw (M8*50) to the heated board which is
electrified, heating the electricity (the temperature is controlled automatically to 250º +15º, red light on when
the electricity is on, operate when the green light is on while the red one is off).
3. When the green light is on, then we can operate and when the pipe and fitting are melt down, shaking the hand
sheel welding the pipe and fitting when their sizes are suitable for needing, keep them heating about 30
minutes.
4. Exit the welded nould fast, press and weld the pipe and the fitting, the welding is over when the temperature
drops down at normal in room.
Welding Heads
Welding Heater
Flange Pipe Clamp
Red Light
Green Light
Screw Handle
Flange Clamp
Handle Grip
Feeding Screw
Pipe Clamp