Induro AM Series User manual

CM-SERIES & AM-SERIES MONOPODS
OPERATING INSTRUCTIONS
Thank you for making Induro your choice for
professional photographic gear. Your Induro gear
is manufactured to provide years of dependable
service. In order to obtain optimum satisfaction
and performance we suggest that you carefully
read these instructions and provide them to
anyone who may also use your Induro gear.
Specifications and design are subject to change without notice.
INDURO Camera Support Gear | 75 Virginia Road, North White Plains, NY 10603 | T 914-347-3300 | F 914-347-3309 | [e-mail] | indurogear.com

SETUP
Head Mounting (FIGURES 1 & 2)
If your Monopod did not come with a Head, select
one of the fine Induro Tripod Heads that match your
size Monopod and install by screwing the Head
clockwise onto the 3/8" Mounting Thread of the Top
Plate. Once it is hand tight, secure by fully tightening
the Head Locking Screw(s) from below with the
included Allen Key.
Most Heads have a 3/8" Base Mount so your Induro
Monopod is shipped with the 3/8 Mounting Thread
exposed, but if the Head you choose uses a 1/4–20
you can attach it by simply reversing the Mounting
Screw. To do this turn the Locking Nut counter-
clockwise (using the supplied Wrench) until it
becomes loose, and unscrew the Mounting Screw
until it can be completely removed. Reverse the
Screw, so that the threads are in position and screw
it back into place, secure with the Locking Nut using
the wrench.
NOTE: Allow enough of the screw threads to be
available for maximum security when the Head is
mounted onto the Monopod. It’s recommended that
at least 5 to 6 threads be exposed before locking the
Mounting Screw in place.
OPERATION
Before using your Monopod, adjust each Leg Section
to the desired height.
Make sure that the Monopod is firmly resting on a
stable surface and mount your camera securely on
the Monopod Head. Always engage any safety locks
on the Monopod Head to prevent any accidental
dismounting.
FOR BEST RESULTS: Do not raise the Monopod
higher than necessary and extend the largest
diameter Leg Sections first.
NOTE: Never carry your Monopod with camera
gear attached.
Leg Section Adjustment (FIGURES 3 & 4)
Each Leg Section can be adjusted to the desired
length by turning the Leg Lock Grip 1/2 turn (180°)
clockwise until the Leg is free to slide in or out. Once
the desired length is achieved, turn the Leg Lock Grip
counter-clockwise until the leg section is securely
locked. Repeat this step for each Leg Section until
the Monopod is set to the desired height.
NOTE: To prevent any accidental damage to your
gear, always remove any mounted equipment
(camera, etc.) from the Monopod before adjusting
the Leg Sections.
USER NOTICE
cDo not exceed the maximum specified load
capacity (see specifications on the package label
or visit www.indurogear.com).
cAlways ensure that Leg and Head Locks are
tightly engaged before mounting any gear on
your Monopod.
cDo not use any Monopod below temperatures of
−4°F or above +158°F (−20°C / +70°C).
cAlways clean and dry any Monopod after it
has been exposed to wet, dusty, sandy or salty
conditions. Your Monopod is not recommended for
use in salt water. If required, clean Monopod using
a mild soap solution applied with a soft cloth, rinse
with fresh water and dry with soft towel. Remove
any dust, dirt or sand from all Leg Locks, Leg
Sections and all moving parts.
cDo not leave any Monopod in the sun for prolonged
periods and avoid high temperature exposure.
cAvoid leaving any Monopod or Tripod unattended in
areas where people could trip over the equipment
and get hurt.
cRemove camera, lens, and all gear from the
Monopod when transporting.
cFor your safety, don’t let your Induro gear come in
contact with any electrical power source.
1
Locking Nut
1/4-20 + 3/8
Mounting Screw
Wrench
2
Unlock Lock
3 4
Top Plate
Leg Lock Grip
Closed Cell Foam Grip
Rubber Foot