INDUSVISION IVEX-FZ Series User manual

IVEX-FZ Series
http://www.indusvision.com
User Manual

01IVEX Series Explosion Proof Camera Manual
IVEX-FZ Series
User Manual
Copyright
© 2021 INDUSVISION Inc. All rights reserved.
Notes on the use of copyrights and trademarks
The names of products and companies mentioned in this manual are trademarks
or registered trademarks belonging to the company. It is a trademark.
Warranty
If the product does not operate properly even though the product is operated under normal
conditions of use, The manufacturer will repair it for free.
The warranty period is 2 years and the following circumstances are excluded from the warranty.
1. When the system operates incorrectly by executing a program not related to the system operation.
2. Changes in the product over time or abnormalities caused by natural wear during use.
※Product appearance and specifications are subject to change without prior notice to improve performance.
Every 3 months to protect personal information safely and prevent personal information theft damage
Change your password periodically.
Users are responsible for security and other issues caused by careless password management.
Be very careful.

02IVEX Series Explosion Proof Camera Manual
03
04
05
07
09
12
14
15
18
19
20
22
23
•Components
•Part names
•Safety Rules
•Identification method
•Precautions before installation
•How to Installation
•Camera self-installation
•NETWORK setting
•Firmware update
•Maintenance
•Troubleshooting
•Technical drawing
•Product warranty
PC system recommended specifications
•CPU : Intel Core 2 Duo 2.4 GHz or more (1920x1080 30fps Use)
Intel Core i7 2.8 GHz or more (1920x1080 60fps Use)
•Resolution : 1280x1024 or more (32 bit color)
•Memory : 2GB or more
•Supported OS: Windows XP, VISTA, 7, 8, 10 / Mac OS 10.7 more
•Support web browser: Microsoft Internet Explorer (Ver. 8~11),
Mozilla Firefox (Ver. 9~19) New 85
Google Chrome (Ver. 15~15) New 88
Apple Safari (Ver. 6.0.2) New 14
- Windows 8 is only supported in desktop mode.
- Beta or developer versions other than those released on the
official website are not supported.
- Windows 7 or higher is recommended for IPv6 connection.
- Safari Browser is only supported on Mac OS X.
•Video memory: 256MB or more
- If the driver of the video memory card is not installed correctly or
is not the latest version, the video may not play properly.
- If more than one monitor is used, playback performance may decrease
depending on the system specifications.
Contents
Summary

M5 M4 M3
03IVEX Series Explosion Proof Camera Manual
Sun shield
User Manual
Cable gland L wrench set Wrench bolt
*2
Hex Bolt Set
*1
*1
*1
*1
•Cable glands and plugs may not be available depending
on the model.
•SMPS is provided as 12V for IVEX-FZ Series.
(However, it is not provided for configurations that do
not require 12V power supply)
•Multi-cable is not provided for PoE-only models.
•The camera sponge and camera mount SET are
exclusive accessories for the FZ-31.
•Therefore, it is not available in configurations other than the
FZ-31 model.
•When purchasing pedestal mount and wall mount bracket,
set anchor 4EA or 6EA is provided as standard.
Lug
*1
+
M5
M5
M3
(Dismantling bolt)
M4*40
M8*15 SET M6
*1
SMPS Multi cable
*1 *1
Camera sponge
*1 *1
Camera mount SET
* See note
Components
Basic Components
Before starting the installation,
remove the following components enclosed in the product box.
Please check carefully to ensure that there are no missing parts during
installation.
Separately Purchased Product
Wall Bracket Set Anchor
Component Notes
L Wrench (Hexagonal) Standard
M4

04IVEX Series Explosion Proof Camera Manual
IVEX-FZ Series
①
②
③
④
⑤
①Camera Housing Cover
②Camera Housing Body
③Sun Shield
④Cable Entry, NPT ¾”
⑤Angle Bracket
Part Names
Part names for each product are important to provide fast and accurate
service for each part, so please be aware of it.

05IVEX Series Explosion Proof Camera Manual
Safety rules
•This product must be installed and maintained by qualified
personnel according to national standards such as
EN/IEC 60079-14, EN/IEC 60079-17, etc.
•Do not open the product with power applied in the
explosion-proof area.
•Installation of the product should be carried out using suitable tools.
•The manufacturer recommends the use of explosion-proof tools.
•Connection testing and maintenance work in non-hazardous areas
is recommended.
•Grounding is essential to reduce the risk of ignition of
products installed in explosive environments.
•The device must be connected to a protective earth.
•At this time, it is recommended to use an approved material for
the grounding cable.
•Before turning on the product in a potentially explosive location,
make sure that the connections, such as cable glands,
are properly closed.
•When the surface temperature of the device rises due to direct
sunlight exposure, the surface temperature rating of the device is
judged only by the ambient air temperature without taking into
account direct sunlight.
•Make sure all devices are certified for the application and the
environment in which they are installed.
•Any changes not approved by the manufacturer are not guaranteed.
Danger of explosion
Be sure to read this to reduce the risk of explosion.
•When installing or performing maintenance while the breaker is ON,
Make sure the product is turned off.
•The power-off device must be included in the electrical installation,
ensuring that it is recognizable very quickly and turns off when
necessary.
•For the electrical installation to which the device is connected,
a maximum of 16A earth leakage breaker is recommended.
The minimum spacing between circuit breaker contacts should be
3 mm (0.1”).
•Do not use worn or corroded cables.
•During installation and operation, check whether the characteristics
of the power supply provided by the facility match the characteristics
of the power supply required by the product.
•This product is not suitable for use in locations where children
may be present.
Please read the product instruction manual carefully before installing and
using this product.
Keep the manual in a separate place for future reference.
Risk of electric shock
To avoid the risk of electric shock, make sure that voltage
is applied to the product before performing any work.

06IVEX Series Explosion Proof Camera Manual
•Make sure the installation method meets the explosion protection
regulations and specifications.
•After connection, it is recommended to test and install in
a non-explosion-proof area before installing in the field.
•Use a suitable cable that can withstand the operating temperature.
•All unused cables must be electrically insulated.
•This product can only be installed in a standard location.
•Make sure the device is securely fixed before applying power.
•When the power is turned on, this product performs several
automatic calibration/inspection tasks.
Do not stand near the device when power is applied.
•Unauthorized modification, use of non-genuine spare parts,
and unauthorized modification by the manufacturer.
We are not responsible for any damage to the equipment caused
by installation, maintenance and repair by unskilled personnel.
•For technical service, refer only to qualified technicians.
•This product should only be repaired by trained personnel
or under the supervision of the manufacturer's personnel.
•When repairing, use only genuine Indusvision parts.
•Strictly follow the maintenance instructions given in these
operating instructions.
•Considering the characteristics of the product, use an appropriate
transport and handling system.
The installer must comply with general accident prevention standards
when handling the product.
•Before proceeding with the installation, compare/check with the
components in the user's manual to check whether they match.
•Equipment installation in hazardous areas is carried out by
specialized technical personnel.
•The manufacturer assumes no responsibility for any damage arising
from improper use of the devices mentioned in this manual.
We also reserve the right to change some parts without mentioning.
•The manufacturer does not accept any responsibility arising from
improper use of the device.
•Since it is the user's responsibility to select the surface on which
the product will be fixed, no fasteners are provided to attach the
product to a specific surface.
It is the responsibility of the installer to select a fixture suitable
for that particular application.
Use installation methods and materials that can support at least
four times the weight of the product.
•Contact the manufacturer for exact explosion-proof joint dimensions
information.
•For all product maintenance, it is recommended that the product be
repaired by sending the product to the manufacturer.
•This is a Class A product. In residential environments,
this product may cause radio interference.
In this case, a suitable electromagnetic shielding method may be
required by the user.
•It is recommended to use an uninterruptible power supply (UPS)
in case of a temporary power outage.
Safety rules
Please read the product instruction manual carefully before installing and
using this product.
Keep the manual in a separate place for future reference.
Caution when working
Operation is very important for the correct functioning of
the system. Please proceed with the installation
in the order indicated in the product instruction manual.
Product feature description
Please read the information below to understand the
installation process.

07IVEX Series Explosion Proof Camera Manual
Certification IVEX-FZ Series Certification Number
IECEx IECEx KGS 14.0001X
ATEX KRH 14 ATEX 1013X
NEPSI GYJ14.1418X
KCs 14-GA2BO-0288X
16-GA2BO-0166X
20-GA2BO-0560X~0565X
IK IK10 : 19-079699-01-1
①
②
③
④
⑤
⑥
⑨
⑩
⑦
⑧
[KOR Ver.] [ENG Ver.]
①
②
③
④
⑤
⑥
⑧
⑦
⑨
⑩
Product specification inspection
Identification method
①Precautions
②Manufacturer and address
③Model name
④Serial number: It consists of a 9-digit system excluding the
model name, and the 6 digits from the left mean
the year, month, and day of production, and
the 3 digits after that represent the product No.
assigned to that year.
⑤Rated operating voltage: It means the rated voltage of the product,
and Class3 =15W.
⑥Operating temperature: ambient temperature
(-25˚C≤Ta≤+65˚C, -25˚C≤Ta≤65˚C or Tx˚C)
⑦T Class (Tx or Tx... Tx)
⑧Maximum surface temperature (Tx˚C or Tx˚C... Tx˚C)
⑨Safety certification issuing organization
⑩Safety certification number

08IVEX Series Explosion Proof Camera Manual
Tempered glass only
-IVEX-FZ-31,30
Tempered glass + wiper
-IVEX-FZ-31W,30W
Tempered glass + infrared LED
- IVEX-FZ-31IR, 30IR
Tempered glass + wiper + infrared LED
-IVEX-FZ-31WIR,30WIR
Germanium glass only
-IVEX-FZ-40
Single Lineup
IVEX-FZ Series
IVEX-FZ Dual Series
Dual Lineup
•The selection of glass cover types for each product line can
be combined with the glass types listed on the left.
•Please contact the manufacturer for details.
Classification by model
Identification method
The explosion-proof certification number may change depending on the
manufacturer's product upgrade status.
Therefore, please refer to the manufacturer's website for exact specifications.

09IVEX Series Explosion Proof Camera Manual
Check the packing box
!
Before proceeding with the installation of the product, carefully read the
chapter'Safety Rules' in the product manual.
Information provided on the
box label
- Model name
- Serial number of the product
- IP address
- ID / Password
- etc
•When delivering the product, check that the packaging is intact,
and that there are no drops or tears.
•In the case of returning a broken product, it is recommended
to use the packaging box provided for transportation.
•The box label affixed to the product box contains the information
shown above. Before discarding the box, please back up the
information entered on the label to prevent product operation
problems.
Check the contents
•Refer to the component information on page 3 and check that
the contents match.
Safe disposal of packaging materials
•Among the packaging materials, PE foam other than paper is
subject to separate discharge.
Therefore, please separate and dispose according to the
separate collection method and regulations.
Check before installation
•It is recommended to use only the brackets and accessories
approved by the manufacturer for the brackets required for
installation.
•The manufacturer is not responsible for any damage caused
by the use of brackets not provided by the manufacturer.
How to install
•This system can only be installed in a standard location.
Precautions before installation

10IVEX Series Explosion Proof Camera Manual
Mounting and fixing to the pole
•Using the provided hexagon bolt SET, fasten the bolt to
the bolt hole between the pole bracket and the product.
•At this time, check that there are no foreign substances in the
thread or the product's fastening hole.
•Before tightening the bolt, apply enough locking compound
(Loctite 263, medium-strength thread locker) to the bolt hole.
•The thread compound should solidify for an hour,
during which time the installation should be completed.
•When tightening the bolts, tighten the torque to 35Nm.
Before proceeding with the installation of the product, carefully read the
chapter'Safety Rules' in the product manual.
Fixed to vertical wall
•The wall mount bracket can be fixed to a vertical wall.
•Fix the bracket to the wall with the provided set anchor that
can withstand at least 4 times the weight of the device.
Then use the provided hexagon bolt SET to fix the device
to the bracket.
•At this time, check that there are no foreign substances in the thread
or the product's fastening hole..
•Apply enough locking compound (Loctite 263) on the two screws
and lock the screws.
•The thread compound should solidify for an hour,
during which time the installation should be completed.
•When tightening the bolt, tighten the torque to 35Nm.
Set anchor Bracket from top to bottom
Precautions before installation

11
Fastening of the sun shield
•When the sun shield provided as an accessory is shipped from
the factory, fix the wrench bolt (M6 SET) fastened to the top of the
housing using the L wrench (M5) to the housing.
•Before bolting, apply enough locking compound (Loctite 263)
to the bolting hole.
•The thread compound should solidify for an hour,
during which time the installation should be completed.
•When tightening the bolts, tighten the torque to 15Nm.
IVEX Series Explosion Proof Camera Manual
Before proceeding with the installation of the product, carefully read the
chapter'Safety Rules' in the product manual.
Precautions before installation

12IVEX Series Explosion Proof Camera Manual
Sealing fitting connection
•When using the sealing fitting,
it is possible to use it normally
when the inside of the sealing fitting
is finished with a compound
as shown in the picture.
Loctite 263
•In the case of sealing fitting, fasten the NPT ¾ nipple of ①
first, and then fasten the sealing fitting of ②
to the opposite side of the nipple.
•Next, when the cable entry is completed, a compound (pipe sealant)
is injected to close the inside of the sealing fitting.
•At this time, apply enough locking compound (Loctite 263)
to the fastening hole.
①
②
It is strongly recommended that all devices be carried out after final testing
prior to installation at the final installation site.
Ground installation method
•M6 Lug
•Material: copper, tin alloy
•The product must be grounded with an external cable
(16AWG) with a 4mm²cross section.
•Use the ground lug provided with the product and
M5*8 (wrench bolt) screws to fix the lug to be used for
power connection to the grounding hole with the L wrench
provided.
•A separate press is required to press the lugs.
•At this time, the presser is not provided separately.
How to Installation

13
Ground installation method
•In the case of the cable gland, it is screwed into the NPT ¾
hole of the device. At this time, do not tighten hard to enter the cable.
•When the cable entry is complete, tighten it with a monkey spanner.
•At this time, apply enough locking compound (Loctite 263)
to the fastening holes.
Loctite 263
IVEX Series Explosion Proof Camera Manual
SMPS connection in explosion-proof
enclosure
•After all installation is complete, install the product and enclosed
SMPS inside the explosion-proof enclosure, and install necessary
devices such as network and other RS-485 controllers.
•Carefully connect +,- of DC-12V power and apply power.
•Carefully check all connections to the product before applying power.
•When the power is applied, if there is no problem,
it is connected to the network and it is in a state that can be
used normally.
•Immediately after detecting an abnormality in the initial state,
turn off the power and contact the manufacturer.
DC12V
NETWORK
etc.
220V GND 12V-12V+
①
It is strongly recommended that all devices be carried out after final testing
prior to installation at the final installation site.
How to Installation

14
Camera self-installation
Open Camera Housing Cover
•For camera mounting, remove and store 8EA of M5*10
wrench bolts on the camera housing cover using L wrench (M4).
•To open the camera housing cover of the product,
use the M4*40 wrench bolt provided as a component as shown
in ②and fasten it to the 2 points of M3 thread.
•Tighten two M4*40 wrench bolts with an L wrench (M3) alternately,
so that the camera housing cover is little by little away from
the body.
•When a certain part of the camera housing cover is far from
the body, pull the camera housing cover by hand as shown
in ③to completely separate the camera housing cover.
IVEX-FZ Series Camera Mounting and
Cable Connection
•As shown in ①, fasten the camera and camera bracket using the
bolts built into the product.
•Insert the camera into the IP bracket as shown in ②
and fasten the camera connected to the bracket as in ①
with the tempered glass as close as possible using the bolts built into
the product when shipped from the product.
•As shown in ③, pass the cable through the NPT Entry of the
camera housing body and connect the camera's Power, CVBS,
and LAN terminals.
•Depending on the product, the shape of the camera bracket and
IP bracket may change, but the mechanism for fastening the camera
is basically the same.
•As shown in ④, pay attention to the cable and the direction
of the camera housing body and assemble in the reverse order of
disassembly.
②③ ①
IVEX Series Explosion Proof Camera Manual
①
④
②
③
LAN Power
CVBS
When replacing or installing the camera, be sure to work in a safe area
outside of the explosion-proof area.

15IVEX Series Explosion Proof Camera Manual
Web browser access
①In Internet Explorer's address bar, enter the IP address
you checked in ‘Checking the packaging box’ on page 10.
②When the web page shown in the picture above appears,
enter your ID and PW, and click the OK button.
③If you log in successfully, you will be taken to the system
settings page.
How to connect for the first time in
Google Chrome
①
②
③
admin
1234
Input new PW
NETWORK setting
After sufficiently checking the IP-related information that can be checked in
‘Checking the packing box’ on page 10, proceed to the following.
The connection is not set to private.
Hacker may be trying to steal information(ex: password,message, creditcard, etc.)
from 192.168.10.100 Learn more
Advanced Click
Help us improveSafe Browsing by sending some system informationand page content to Google.
Privacy Policy
Return to safety page
Live System setting
Server 10.20.30.40 is requesting usernameand
password.
That server alsoreports "GoAhead".
Remember my credentials
Confirm Cancel
Windows security
Caution
Privacy error
Chrome is not set as the default browser. Set as default browser
D
It cannot be verifiedthat this server is 192.168.10.100,
and it is not a security certificatetrusted by the computer operating system.
This may be because the server is configuredincorrectly,
or an illegal user is interceptingthe connection.
Go to 192.168.10.100 (not secure) Click
admin
1234 D
Login
Input new PW

16IVEX Series Explosion Proof Camera Manual
IP address change
•When selecting Fixed IP in IP setting, all settings except
DNS must be entered in the setting window as shown in the
figure above.
•At this time, the gateway of the PC to which the router
and web viewer are to be connected must match the camera.
•The IP address must also match the camera with all numbers
except for the 4th digit address, such as 192.168.1.X.
•It takes about 30-40 seconds for the settings to be applied.
If you do not want to apply the changed contents, you can
cancel the changed contents by clicking the Back button.
•Dynamic IP (DHCP) setting does not require the above IP setting.
Change Web Port
• Go to Basic Setting → IP Address.
Service
IP Address 192.168.1.20
Subnet Mask 255.255.255.0
Gateway 192.168.1.1
DNS 1 168.126.63.1
DNS 2 168.126.63.2
IPv4
Apply
Fixed IP Dynamic IP
HTTP
HTTP Enable
HTTP Port 80 (Default: 80, 80 ~ 65535)
HTTPS
HTTPS Enable
HTTPS Port 443 (Default: 443, 443 ~ 65535)
SHA256
SHA256 Enable
Used
Used Not Used
Not Used
Used Not Used
• Go to Basic Setting → Web Port.
Apply
Return
•The default setting of Web Port is as shown in the figure.
•The HTTP port is for web access, video streaming,
and playback.
•The HTTP port is the network port that the PC uses to access
the product's web page, and can be used by specifying a port
in the range of 80 to 65535.
The default is 80
•The above setting can be changed by the user,
but the port is a general setting, so the manufacturer is
not responsible for any problems caused by the change.
•SHA256: Set whether to use SHA256 encryption.
•Both HTTP Port and HTTPS Port cannot be set to Disable.
Either of them must be enabled.
NETWORK setting

17IVEX Series Explosion Proof Camera Manual
RTP/RTSP setting •Service : Set whether to use RTP/RTSP.
•RTSP Port : Set the RTSP Port. The default value is 554.
•Packet Size : This is the menu to set the packet size to be
transmitted to RTP/RTSP.
If the value is low, compatibility with many S/Ws is maintained.
It divides and transmits a small amount of packets.
•The higher the value, the fewer the number of packets transmitted
by dividing.
However, if the program does not support the high value,
the video will not be displayed.
•Keep-Alive : It sends the current camera status through continuous
UDP communication. Some S/W and equipment are
not supported.
•RTP Auth Algorithm : Set the RTP encryption authentication method.
MD5 is highly compatible with many S/Ws.
If it is set to SHA256, stronger encryption is applied,
but it cannot be played on S/W or devices that do not support
SHA256 such as VLC.
•Go to Basic Setting -> RTP / RTSP.
•RTSP URL is supported for two types, Unicast and Multicast.
•The RTSP address of Unicast is as follows. (General use)
- Primary Stream (Channel 1) : rtsp://camera IP/cam0_0
- Secondary Stream (Channel 2) : rtsp://camera IP/cam0_1
- Tertiary Stream (Channel 3) : rtsp://camera IP/cam0_2
•The RTSP address of Multicast is as follows.
•To use Multicast, Multicast must be set.
- Primary Stream (Channel 1) : rtsp://camera IP/mcam0_0
- Secondary Stream (Channel 2) : rtsp://camera IP/mcam0_1
- Tertiary Stream (Channel 3) : rtsp://camera IP/mcam0_2
Service
RTSP Port (Default: 554, 554 ~ 65534)
Packet size (Default: 1, 1 ~ 12)
Keep-Alive
RTP Auth Algorithm
Camera 1
Multicast
Address
Not used: 0.0.0.0
(225.0.0.0 ~ 239.255.255.255)
Multicast Port (Not used: 0, 2048 ~65534)
Camera 2
Multicast
Address
Not used: 0.0.0.0
(225.0.0.0 ~ 239.255.255.255)
Multicast Port (Not used: 0, 2048 ~65534)
Camera 3
Multicast
Address
Not used: 0.0.0.0
(225.0.0.0 ~ 239.255.255.255)
Multicast Port (Not used: 0, 2048 ~65534)
0.0.0.0
0
0.0.0.0
0
0.0.0.0
0
1
554
Used Not Used
ON OFF
MD5 SHA256
Apply
Return
•RTSP (Real-time Streaming Protocol) is a protocol used to
transmit video and audio streams over a network.
Apple QuickTime and VLC programs are also supported,
but may not be available in a network environment where
a firewall is used. There are two ways to utilize
RTSP: unicast and multicast.
RTP / RTSP setting details
RTSP URL
NETWORK setting

18IVEX Series Explosion Proof Camera Manual
Camera firmware update
•Go to Other tools -> Update -> Start.
•When the update confirmation
window appears as shown on the
left, click the OK button.
•If pop-ups are blocked, the
update window will not appear.
•Please proceed to unblock pop-
up first.
•Select the update file and click
the Next button.
•When uploading is complete,
the message shown on the left
appears. Click the Next button
to proceed.
•Select whether to proceed with
the firmware update as it is or to
initialize it.
•Next: Maintains the current
settings and proceeds with the
firmware update.
•Restore Default: Initializes the
current settings and updates the
firmware.
•After a while, a Reboot
message appears. Click the
Reboot button to complete the
firmware update.
•If the camera is turned off
before the update is complete,
the firmware may be severely
damaged.
•When the update is complete,
the web browser will be
launched automatically.
Firmware update
Updating the product's firmware may cause the product to stop functioning.
So please proceed carefully.

19
•It should not show any signs of cable damage or wear that
could lead to a hazardous situation. In this case,
special maintenance is essential.
•Replacement of gaskets and O-rings is essential for maintenance.
•Gaskets and O-rings damaged during maintenance
may cause serious problems in product performance,
so be sure to replace them with genuine parts guaranteed by
the manufacturer. •It must be managed regularly so that dust does not accumulate
more than 5mm on the surface of the product through routine
cleaning. (To prevent static electricity)
•Tempered glass glass should be cleaned with mild soapy
water diluted with water.
•Germanium glass should be cleaned carefully to avoid scratching
or damaging the carbon-coated surface.
•Damage to the germanium glass coating may reduce the UV
transparency of the surface.
•When cleaning the germanium glass, loosen the bolts on the
germanium glass protector grid, clean it with mild soapy water
diluted with water, and then assemble again.
•The surface of the device must be cleaned with a damp cloth.
Replacement of wiper
•In the case of models equipped with a wiper, the blade may be
worn and the image quality may deteriorate. In this case,
you can replace the wiper blade by loosening the bolt that secures
the wiper blade and pulling it by hand as shown in the figure.
•When replacing, if the wiper blade is pushed from side to side
severely, the wiper motor may fail.
※ Wiper Blade SET
IVEX Series Explosion Proof Camera Manual
Maintenance
Parts used for maintenance of the device are guaranteed by the manufacturer.
The manufacturer guarantees only the use of genuine parts.
Summary
Cleaning
Disposal of replaced parts
•Disposal of the device must be properly disposed of in
accordance with the Electronic Waste Directive and
environmental regulations.