Inepro 132300 User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub
132300
Konica Minolta Kit - Bizhub
132300
Inepro Kit number: 132300
Konica Kit number: 9967000514

Version 2.2.30 Inepro B.V.http://www.inepro.com
Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 8
........................................................................................................................................................ 91 Attach the PayCon to the bracket
........................................................................................................................................................ 112 Attach the bracket to the copier
Set up the copier 14
........................................................................................................................................................ 151 Konica Minolta Bizhub C350
........................................................................................................................................................ 162 Other Konica Minolta Bizhub Colour copiers
Set up the PayCon 18
........................................................................................................................................................ 191 Behaviour
........................................................................................................................................................ 202 Network
........................................................................................................................................................ 213 General Settings
Notes 24

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub 132300
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
- Bizhub C250
- Bizhub C252
- Bizhub C300
- Bizhub C350
- Bizhub C351
- Bizhub C352
- Bizhub C450
- Bizhub C451
- Bizhub C550
- Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub 132300
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub colour
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub colour
In the "KM Mounting kit for Bizhub colour" you should find:
· 1x PayCon copier mounting bracket
· 1x KM cableset Minolta serial I/F
· 1x KM screwset Bizhub colour
· 1x KM Mounting plate Bizhub colour
· 1x This manual

5
KM Screwset Bizhub colour
KM Screw set Bizhub colour
In the "KM Screwset Bizhub colour" you should find:
· 20x Cable guiders
· 3x M4 x 5mm Dome shaped, cross head screws
· 4x M4 x 20mm Dome shaped, cross head screws
· 7x M4 Star lock washers
KM Mounting plate Bizhub colour
KM Mounting plate Bizhub colour
1x KM mounting plate Bizhub colour

6 - Konica Minolta Kit - Bizhub 132300
Check Kit Content
KM Cableset Minolta serial I/F
KM Cableset Minolta serial I/F
In the "KM Cableset Minolta serial I/F" you should find:
· 1x Rip tie
· 1x Ferrite core
· 1x Connection cable
· 1x Double sided adhesive tape 25mm x 30mm

7
PayCon copier mounting bracket
PayCon copier m ounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x PayCon copier mounting bracket
· 4x Dome shaped, cross head screws
· 3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
· Konica Minolta vendor kit VK-501 should be installed in the copier (not included in this kit)

Hardware Setup
Part
III

9
Hardware Setup
Additional requirements:
· Pair of wire cutters
· No. 2 cross head screwdriver
· No. 1 PosiDriv head screwdriver
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
Attach the PayCon to the PayCon bracket
Please follow these steps:
1. Break out the appropriate gaps in the flaps
2. Feed the wires through the bracket and through the compartm ent border in the PayCon, then connect them as show n to the
'Copy_Out' and the 'Opto COM 12'. Also connect the pow er supply to the socket bottom -left to the 'Opto COM 12' as show n in
the picture on the right.

10 - Konica Minolta Kit - Bizhub 132300
Hardware Setup
3. Close the tw o left flaps and fasten the m iddle one w ith it's screw . Then use the rip tie to attach the pow er cable and
connection cable to the right flap, thus creating a cable relief, and clip the rip tie using the w ire cutter.
4. Close and gently screw dow n the final flap
5. Place the PayCon bracket on the PayCon w ith the screw s from the bracket kit, (you don't need the three smaller screw s).

11
Attach the PayCon to the bracket
6. Align the holes of the mounting plate with the PayCon bracket and fasten it w ith the 3 M4 x 5mm screw s and their star lock
w ashers
7. Gently open the ferrite core and loop the connection and netw ork cables through once and loop the pow er supply cable
through twi ce. Then gently close the ferrite cores and attach them to the PayCon using the adhesive tape
Attach the PayCon bracket to the copier
1. Rem ove any rubber protection caps covering the screw holes and attach the mounting plate to the copier with the 4 M4 x
20mm screw s and the ir star lock w ashers

12 - Konica Minolta Kit - Bizhub 132300
Hardware Setup
2. Guide the w ires on the copier w ith the 20 w ire guiders and connect the interface cable to the connector of the Konica Minolta
VK-501 vendor kit (not included)
3. Rem ove the transport foils to finish the installation

13
Attach the bracket to the copier
4. Finished

Set up the copier
Part
IV

15
Set up the copier
Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings
below.
Konica Minolta Bizhub C350
· Konica Minolta Bizhub C350
The PayCon Interface setting should be 'Minolta Serial'. (See chapter: 'Set up the PayCon' on page ).
Activating the payment system:
1. Press <Utility>
2. Press <Meter count>
3. Press <stop> <0> <0> <stop> <0> <1> SERVICE MODE
4. Press <0> <0> <0> <0> <0> <0> <0> <0> <"Enter">
5. Press <stop> <9> - select <admin choice>
6. Press <Vendor "SET">
7. Select <Interface "Type 1">
- Select <Message "Type 2"> (for cards only)
8. Leave the menu
19

16 - Konica Minolta Kit - Bizhub 132300
Set up the copier
Other Bizhub Colour copiers
· Konica Minolta Bizhub C250
· Konica Minolta Bizhub C252
· Konica Minolta Bizhub C300
· Konica Minolta Bizhub C351
· Konica Minolta Bizhub C352
· Konica Minolta Bizhub C450
The PayCon Interface setting should be 'KoMi Serial'. (See chapter: 'Set up the PayCon' on page ).
Activating the payment system:
1. Press <Utility>
2. Press <Details>
3. Press <Stop> <0> <0> <Stop> <0> <1> SERVICE MODE
4. Press <Stop> <9>
5. Select <Management Function Choice>
6. Select <Vendor 2>
7. Select <Message>
- Select <Type2> (for cards only)
8. Leave the menu
19

17
Other Konica Minolta Bizhub Colour copiers
Setting / unsetting restrictions of the MFP (default is all functionality maximum restricted!):
1. Press <Utility>
2. Select <Administrator Setting> (or press <3>)
3. Press <1> <2> <3> <4> <5> <6> <7> <8> <OK>
4. Select <Security Setting> (or press <9> (Phase 1.8), or press <0> (Phase 3.0))
5. Select <Management Function Setting> (or press <6> (Phase 1.8), or press <7> (Phase 3.0))
6. Select <Function Settings> (or press <1>)
7. Set <ON>, <OFF> or <Disable> for each individual function (Copy, Print and Send Scan/Fax)
- ON: functionality only allowed when enough credit available from PayCon / PayMatic
- OFF: functionality available without any restrictions
- Disable: functionality complete switched off for every usage
8. Leave the menu
Note:
· When "Print Function Setting" is set to "ON", all print jobs need a job log code. Print jobs without this code will be
automatically deleted at the MFP.
· When using central server software for controlling print jobs "Print Function Setting" should be set to "OFF" (otherwise
you have to pay twice).

Set up the PayCon
Part
V