Inepro 132361 User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub -
132361
Konica Minolta Kit - Bizhub
- 132361
Inepro Kit number: 132361
Konica Kit number: 9967000723

Version 2.2.30 Inepro B.V.http://www.inepro.com
Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 9
........................................................................................................................................................ 101 Attach the PayCon to the bracket
........................................................................................................................................................ 112 Attach the bracket to the copier
Set up the copier 17
........................................................................................................................................................ 181 Konica Minolta Bizhub 361 Series
Set up the PayCon 20
........................................................................................................................................................ 211 Behaviour
........................................................................................................................................................ 222 Network
........................................................................................................................................................ 233 General Settings
Notes 26

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub - 132361
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
- Bizhub 361
- Bizhub 421
- Bizhub 501
- Bizhub C451
- Bizhub C550
- Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub 361, 421, 501
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub 361, 421, 501
In the "KM Mounting kit for Bizhub 361, 421, 501" you should find:
· 1x PayCon copier mounting bracket
· 1x KM cableset Minolta Serial I/F - V3
· 1x KM screwset Bizhub 361, 421, 501
· 1x KM Mounting plate Bizhub 361, 421, 501
· 1x This manual
· 1x 1 m grey cat 5 network cable

5
KM Screwset Bizhub 361, 421, 501
KM Screwset Bizhub 361, 421, 501
In the "KM Screwset Bizhub 361, 421, 501" you should find:
· 3x M4 x 5mm Dome shaped, cross head screw
· 1x M4 x 16mm Dome shaped, cross head screw
· 2x M3 x 12mm Dome shaped, cross head screw
· 1x M3 x 10mm Dome shaped, countersunk cross head screw
· 1x M3 x 10mm Dome shaped, cross head screw
· 1x M3 x 20mm Dome shaped, cross head screws
· 1x M3 x 20mm Dome shaped, countersunk cross head screw
· 2x M3 Star lock washer
· 3x M4 Star lock washer
· 2x M3 x 5mm spacer
· 1x M4 x 5mm spacer
· 2x M3 Black nylon cable guider
· 1x M4 Black nylon cable guider
· 3x Rip Ties
· 1x 56cm x 15mm Black slit wrap harness (the black hose)
The black slit harness (the black hose) is not visible in the image.

6 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
KM Mounting plate Bizhub 361, 421, 501
KM Mounting plate Bizhub 361, 421, 501
1x KM mounting plate Bizhub 361, 421, 501

7
KM Cableset Minolta serial I/F V3
KM Cableset Minolta serial I/F V3
In the "KM Cableset Minolta serial I/F V3" you should find:
· 3x Rip ties
· 1x Ferrite core
· 1x Connection cable
· 1x Double sided adhesive tape 25mm x 30mm
· 1x Connector block male/male

8 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
PayCon copier mounting bracket
PayCon copier m ounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x PayCon copier mounting bracket
· 4x Dome shaped, cross head screws
· 3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)

Hardware Setup
Part
III

10 - Konica Minolta Kit - Bizhub - 132361
Hardware Setup
Hardware Setup
Additional requirements:
· Pair of wire cutters
· No. 2 cross head screwdriver
· No. 1 PosiDriv head screwdriver
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)
Recommend Tools:
· SHR Slit Wrap Tool, Richco part nr. CAT-15-PP (for guiding cables into the slit harness wrap)
Attach the PayCon to the PayCon bracket
1. Break out the appropriate gaps in the flaps
2. Close the tw o left flaps and fasten the m iddle one w ith it's screw. Feed the w ires through the bracket and connect the
pow er supply to the socket bottom -left to the 'Opto COM 12' and the copier cable to 'Opto COM 12' as show n in the picture

11
Attach the PayCon to the bracket
3. Use the rip tie to attach the pow er cable and connection cable to the flap, thus creating a cable relief, and clip the rip tie using
the w ire cutter
4. Close and gently screw dow n the last flap and place the PayCon bracket on the PayCon w ith the screw s from the bracket kit
5. Place the ferrite cores and loop the netw ork cables through them once
Attach the PayCon bracket to the copier
The mounting instructions differ for the different type of copiers its supports. The instructions for each part will start with the
list of copiers that the instructions are meant for.
-Bizhub 361
-Bizhub 421
-Bizhub 501

12 - Konica Minolta Kit - Bizhub - 132361
Hardware Setup
1.
Rem ove the 4 screw s, located on
the right side of the copier
Rem ove the screw s located on the left
side of the copier to take off the plastic
cover
2. Remove the metal plate, m ind the optional hard disk drive.

13
Attach the bracket to the copier
3. Screw the mounting plate w ith four screw s on the copier and attach the cable guides.
4. Screw the PayCon on the mounting plate, w ith the three screw s

14 - Konica Minolta Kit - Bizhub - 132361
Hardware Setup
5. Feed the cable to the backside of the copier through the inside.
6. Mount the hose and attach it to the cable guides w ith the rip ties.

15
Attach the bracket to the copier
7. Take the cable from the front, hook it to the clip, place the ferrite core, loop cable through and connect it to the connector
board
8. Place the metal cover back on the copier

16 - Konica Minolta Kit - Bizhub - 132361
Hardware Setup
9. Remove the transport foils to finish the installation
Finished

Set up the copier
Part
IV

18 - Konica Minolta Kit - Bizhub - 132361
Set up the copier
Set up the copier
Turn on the copier. In this chapter you will set up the copier for use with the PayCon system. Examine the exact settings
below.
Konica Minolta Bizhub 361 Series
· Konica Minolta Bizhub 361
· Konica Minolta Bizhub 421
· Konica Minolta Bizhub 501
The PayCon Interface setting should be 'KoMi Serial'. (See chapter: 'Set up the PayCon' on page ).
Activating the payment system:
Press <Utility/Counter>
Press <Meter Count>
Press <Check Details>
Press <stop> <0> <0> <stop> <0> <1> SERVICE MODE
Press <stop> <9>
Select <Management Function Choice>
Select <Vendor 2>
Select <Message>
Select <Type1> (for coins only) or
Select <Type2> (for cards only) or
Select <Type3> (for coin & card)
Leave the menu
21