Inepro 132305 User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub
132305
Konica Minolta Kit - Bizhub
132305
Inepro Kit number: 132305
Konica Kit number: 9967000514

Version 2.2.30 Inepro B.V.http://www.inepro.com
Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 8
........................................................................................................................................................ 91 Attach the PayCon to the bracket
........................................................................................................................................................ 102 Attach the bracket to the copier
Set up the copier 16
........................................................................................................................................................ 171 Konica Minolta Bizhub Colour V2
Set up the PayCon 19
........................................................................................................................................................ 201 Behaviour
........................................................................................................................................................ 212 Network
........................................................................................................................................................ 223 General Settings
Notes 25

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub 132305
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
- Bizhub C250
- Bizhub C252
- Bizhub C300
- Bizhub C351
- Bizhub C352
- Bizhub C450
- Bizhub C451
- Bizhub C550
- Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub 132305
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub colour V2
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub Colour V2
In the "KM Mounting kit for Bizhub Colour V2" you should find:
· 1x PayCon copier mounting bracket
· 1x KM cableset Minolta Serial I/F - V2
· 1x KM screwset Bizhub Colour - V2
· 1x KM Mounting plate Bizhub Colour - V2
· 1x This manual
· 1x 100cm Cat 5 network cable

5
KM Screwset Bizhub Colour V2
KM Screw set Bizhub Colour V2
In the "KM Screwset Bizhub Colour V2" you should find:
· 3x M4 x 5mm Dome shaped, cross head screws
· 4x M4 x 20mm Dome shaped, cross head screws
· 7x M4 Star lock washers
· 1x M3 x 10mm Dome shaped, cross head screw
· 1x M3 x 16mm Dome shaped, cross head screw
· 1x M3 x 25mm Dome shaped, cross head screw
· 1x M3 x 3mm spacer
· 1x M3 x 7,5mm spacer
· 1x M3 x 15mm spacer
· 2x M3 Black nylon cable guiders
· 2x Rip Ties
· 1x 58cm x 15mm Black slit wrap harness (the black hose)
KM Mounting plate Bizhub Colour V2
KM Mounting plate Bizhub Colour V2
1x KM mounting plate Bizhub Colour V2

6 - Konica Minolta Kit - Bizhub 132305
Check Kit Content
KM Cableset Minolta serial I/F V2
KM Cableset Minolta serial I/F V2
In the "KM Cableset Minolta serial I/F V2" you should find:
· 1x Rip tie
· 1x Ferrite core
· 1x Connection cable
· 1x Double sided adhesive tape 25mm x 30mm
· 2x Nylon cable guiders

7
PayCon copier mounting bracket
PayCon copier m ounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x PayCon copier mounting bracket
· 4x Dome shaped, cross head screws
· 3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)

Hardware Setup
Part
III