Inepro 132361 User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub -
132361
Konica Minolta Kit - Bizhub
- 132361
Inepro Kit number: 132361
Konica Kit number: 9967000723

Version 2.2.30 Inepro B.V.http://www.inepro.com
Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 9
........................................................................................................................................................ 101 Attach the PayCon to the bracket
........................................................................................................................................................ 112 Attach the bracket to the copier
Set up the copier 17
........................................................................................................................................................ 181 Konica Minolta Bizhub 361 Series
Set up the PayCon 20
........................................................................................................................................................ 211 Behaviour
........................................................................................................................................................ 222 Network
........................................................................................................................................................ 233 General Settings
Notes 26

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub - 132361
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
- Bizhub 361
- Bizhub 421
- Bizhub 501
- Bizhub C451
- Bizhub C550
- Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub 361, 421, 501
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub 361, 421, 501
In the "KM Mounting kit for Bizhub 361, 421, 501" you should find:
· 1x PayCon copier mounting bracket
· 1x KM cableset Minolta Serial I/F - V3
· 1x KM screwset Bizhub 361, 421, 501
· 1x KM Mounting plate Bizhub 361, 421, 501
· 1x This manual
· 1x 1 m grey cat 5 network cable

5
KM Screwset Bizhub 361, 421, 501
KM Screwset Bizhub 361, 421, 501
In the "KM Screwset Bizhub 361, 421, 501" you should find:
· 3x M4 x 5mm Dome shaped, cross head screw
· 1x M4 x 16mm Dome shaped, cross head screw
· 2x M3 x 12mm Dome shaped, cross head screw
· 1x M3 x 10mm Dome shaped, countersunk cross head screw
· 1x M3 x 10mm Dome shaped, cross head screw
· 1x M3 x 20mm Dome shaped, cross head screws
· 1x M3 x 20mm Dome shaped, countersunk cross head screw
· 2x M3 Star lock washer
· 3x M4 Star lock washer
· 2x M3 x 5mm spacer
· 1x M4 x 5mm spacer
· 2x M3 Black nylon cable guider
· 1x M4 Black nylon cable guider
· 3x Rip Ties
· 1x 56cm x 15mm Black slit wrap harness (the black hose)
The black slit harness (the black hose) is not visible in the image.

6 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
KM Mounting plate Bizhub 361, 421, 501
KM Mounting plate Bizhub 361, 421, 501
1x KM mounting plate Bizhub 361, 421, 501

7
KM Cableset Minolta serial I/F V3
KM Cableset Minolta serial I/F V3
In the "KM Cableset Minolta serial I/F V3" you should find:
· 3x Rip ties
· 1x Ferrite core
· 1x Connection cable
· 1x Double sided adhesive tape 25mm x 30mm
· 1x Connector block male/male

8 - Konica Minolta Kit - Bizhub - 132361
Check Kit Content
PayCon copier mounting bracket
PayCon copier m ounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x PayCon copier mounting bracket
· 4x Dome shaped, cross head screws
· 3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)