Inepro 132360 User manual

© 2019 Inepro B.V. All rights reserved
Installation Manual | Konica Minolta Kit - Bizhub
132360
Konica Minolta Kit - Bizhub
132360
Inepro Kit number: 132360
Konica Kit number: 9967000514

Version 2.2.20 Inepro B.V.http://www.inepro.com
Table of Contents
Introduction 1
Check Kit Content 3
Hardware Setup 8
........................................................................................................................................................ 91 Attach the PayCon to the bracket
........................................................................................................................................................ 102 Attach the bracket to the copier
Set up the copier 16
........................................................................................................................................................ 171 Konica Minolta Bizhub 420 Series
Set up the PayCon 19
........................................................................................................................................................ 201 Behaviour
........................................................................................................................................................ 212 Network
........................................................................................................................................................ 223 General Settings
Notes 25

Introduction
Part
I

2 - Konica Minolta Kit - Bizhub 132360
Introduction
Introduction
This kit is meant for the following Konica Minolta Bizhub copiers:
Konica Minolta
- Bizhub 360
- Bizhub 420
- Bizhub 500
- Bizhub C451
- Bizhub C550
- Bizhub C650
To install this kit we shall:
1. Check the content of kit, read more on page
2. Prepare and construct the hardware. To read more go to page
3. Set up the copier, read more on page
4. Set up the PayCon, you will find more information on page
4
4
4
4

Check Kit Content
Part
II

4 - Konica Minolta Kit - Bizhub 132360
Check Kit Content
Check Kit Content
Before you start installing the kit, you should check if you have received all the packages you need.
KM Mounting kit for Bizhub 420 / 500
Please check the content of the box and make sure all kits are complete.
KM Mounting kit for Bizhub 420 / 500
In the "KM Mounting kit for Bizhub 420 / 500" you should find:
· 1x Cable for Konica Minolta Bizhub 420 / 500 serial interface
· 1x PayCon copier mounting bracket
· 1x KM screwset Bizhub 420 / 500
· 1x KM Mounting plate Bizhub 420 / 500
· 1x 65cm x 15mm Black slit wrap harness (the black hose)
· 1x This manual

5
KM Screwset Bizhub 420 / 500
KM Screw set Bizhub 420 / 500
In the "KM Screwset Bizhub 420 / 500" you should find:
· 4x M3 Black nylon cable guiders
· 3x M4 x 5mm Dome shaped, cross head screws
· 3x M3 x 12mm Dome shaped, cross head screws
· 1x M3 x 16mm Dome shaped, cross head screw
· 2x M3 x 20mm Dome shaped, cross head screws
· 2x M3 Star lock washers
· 3x M4 Star lock washers
· 4x Rip Ties
· 1x M3 x 10mm spacer
· 2x M3 x 5mm spacer

6 - Konica Minolta Kit - Bizhub 132360
Check Kit Content
KM Cableset serial 420 / 500
KM Cableset serial 420 / 500
In the "KM Cableset serial 420 / 500" you should find:
· 3x Rip tie
· 1x Ferrite core
· 1x 25 x 30mm Double-sided adhesive tape
· 1x Connection cable
KM Mounting plate Bizhub 420 / 500
KM Mounting plate Bizhub 420 / 500
1x KM mounting plate Bizhub 420 / 500

7
PayCon copier mounting bracket
PayCon copier m ounting bracket
In the "PayCon copier mounting bracket" you should find:
· 1x PayCon copier mounting bracket
· 4x Dome shaped, cross head screws
· 3x Dome shaped, cross head screws (not needed for this installation)
Additional requirements for installation
· PayCon Copy
· 2x CAT-5 Network cables (one cable included)

Hardware Setup
Part
III