Combi F72 Installation instructions

Combi Baby Keep Fit F72
Instruction Manual • Inspection Manual
This document contains information that is required to use Combi Baby Keep Fit F72 safely and
comfortably. Read this manual thoroughly before use to ensure correct use and inspection of the
product. Please keep this manual carefully.
1
(A4) 133856040 190131(1)
This manual can also be downloaded (PDF) from the CombiWith
website. Please make the best use of it.
Chair for Babies "Baby Keep"
Save This Manual for Future Reference
Combi Baby Keep Fit F72
Parts Replacement Procedure Manual
After replacing parts, be sure to inspect
them in accordance with the contents of
"Daily Inspection" on page 4.
Warning
After replacing parts, be sure to inspect
them in accordance with the contents of
"Daily Inspection" on page 4.
Warning
After removing the seat pad, remove the
adhesive remaining on the main body com-
pletely. If a new seat pad is applied while
the adhesive remains, it makes it easier to
peel off.
Caution
After replacement, use the reverse procedure to install the back cushion.
Back Cushion Replacement Procedure
1Insert a flat-head screwdriver into
the insertion guide and lift the back
cushion.
(There is a guide for inserting at the
center of the bottom of the back
cush ion)
2Remove the lower part of the back
cushion from the back plate, and
pull the whole back cushion toward
you to remove it from the back
plate.
After replacement, install the seat pad using the reverse procedure.
If any abnormalities in the back cushion
are found, it is recommended to pur-
chase a back cushion to replace it using
the method shown on the right.
If any abnormalities in the seat pad are
found, it is recommended to purchase a
seat pad to replace it using the method
shown on the right.
Seat Pad Replacement Procedure
The seat pad is mounted with dou-
ble-sided tape.
Back cushion
Back plate
Seat pad
Back cushion
If any abnormality is detected during daily inspection or periodic inspection, and the parts are replaced with new ones.
Read this replacement procedure manual thoroughly to replace them correctly.

2
Warning
Caution
Application of Product
1
Safety Guidelines for Using the Product
2
Combi Baby Keep Fit F72
Instruction Manual
●Combi Baby Keep Fit F72 (hereafter referred to as "this product") is a chair dedicated for babies where children
can be seated with peace of mind. This product is intended for indoor use.
● If the Products is not used in compliance with the content of this instruction manual, it may cause a risk of injury to
the child or the user or a risk of property damage. The content related to safety is separated into Warnings and Cau-
tions depending on the severity of the risk. Read these guidelines before use and follow them to ensure safety.
Ignoring the instruction or misuse may result in severe injury or death.
Ignoring the instruction or misuse may result in injury or property damage.
Request to the Facility
3
Warning
Children may stand up and fall out.
● When installing the product, make sure that there is no object in the area where child's feet
may reach.
● Do not use the product other than the intended purpose.
If it is used by mistake or if a child plays with it, it may cause injury or serious accident.
● Do not leave the product needs repair.
If the inspections are not carried out, degradation or damage of the product may not be discovered,
which may cause injuries or serious accidents.
● Daily inspections and periodic inspections are required to ensure safe use of the product.
It may cause an unexpected accident.
● Do not modify the product.
For inspection methods, refer to the "Inspection Manual" on page 4 of this manual.
This product is intended for use with children seated. After installation, clean it regularly to keep it clean. Do not wash
with water. If it is soiled severely, wipe it off with diluted neutral detergent and wipe it off with a dry cloth again.
Cleaning Method
Caution
● Do not apply water to the product with a hose or apply extreme moisture. Corrosion of the compo-
nents may cause the product to fall off and it causes injury or serious accidents.
● Do not use detergents other than neutral detergents. The plastic may deteriorate, fade, or crack
and be damaged.
7
After the periodic inspection, enter the inspection
date on the inspection sticker affixed to the lower
cover.
D. Entering Inspection Date
B. Checking Missing or Loosening of Various Screws (when corner bracket is used)
C. Checking Appearance (Metal Parts)
After checking, assemble by the reverse procedure.
When assembling, make sure that anchor bolts (3 locations), main unit fixing screws (4 locations), and lower cover
fixing screws (2 locations) are not missing or loosened.
After the assembly is completed, inspect it by referring to the Daily Inspection (page 4).
❹ Checking Corner Cover Fixing Screws and Corner Bracket Fixing Screws.
❺ Checking Anchor Bolts, Body Fixing Screws, and Lower Cover Fixing Screws.
*The corner bracket is sold separately.
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❹
Corner cover fixing screws (2 locations)
Corner bracket fixing screws (4 locations)
❺
Anchor bolts (3 locations)
Main unit fixing screws (4 locations)
Bottom cover fixing screws (2 locations)
Retightening
Retightening
Visual, Touch
(Phillips screwdriver No2)
Visual, Touch
(Phillips screwdriver No3,
spanner (nominal 17MM))
No missing or looseness
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❻
Deformation or rust of main body frame Discontinuation
of use
Visual No deformation or rust
❼
Missing, loss, deformation, rust of screws
and metal fittings ReplacementVisual No disconnection, loss,
deformation, or rust
No missing or looseness
Use a back cushion and a flat-head screwdriver to
remove the plastic caps (2 pcs), then use a Phillips
screwdriver No3 to remove the lower cover fixing
screws (2 locations ) and remove the lower cover.
*To disassemble the back cushion, refer to "Back
Cushion Replacement Procedure" on page 9.
①
Use a Phillips screwdriver No2 to check the
corner cover fixing screws (2 locations) and
corner bracket fixing screws (4 locations) are
not missing or loosened.
③
Using a Phillips screwdriver No3 to remove the main body
fixing screws (4 locations) and use wrench (nominal
17mm) to remove the anchor bolts (3 locations) driven
into the floor, and then remove the main body from the
corner bracket.
②
*The illustrations used in this manual may differ slightly from the product in order to provide an easy-to-understand explanation
of how to operate the product.
Main body
Corner bracket
Anchor bolts
(3 locations)
Body fixing screws
(4 locations)
Inspection sticker
(Inspection S for 1-year silver)
Use Phillips screwdriver No3 and wrench (nominal 17MM)
Corner bracket
Corner bracket
fixing screws
(4 locations)
Bottom cover fixing screws
(2 locations)
Plastic cap (2 pcs)
Bottom cover
Back cushion
Corner cover fixing
screws (2 locations)
Corner cover
Back side of
the main unit

3
*Product specifications are subject to change without prior notice for product improvements.
*When disposing of the product, please dispose it properly in accordance with the local legislation of waste disposal.
*The dimensions and mass of the product are for reference only.
Product Specifications
4
Part Name
5
Product Life
Material
Color
Product Weight (Standard Specification)
External Dimensions
Maximum Load
Weight Limit
Target Age
Product Name
Product No.
How to Use
6
Warning Caution
Make sure to seat the child
by caregiver.
Be sure to use the product correctly according to the warnings below.
Keep eyes on
child all the time Do not leave Do not play with it No Fire
7 years Please replace the product after passing the product life.
Body/Steel (anti-rust treatment), ABS Plastic
Seat Pad/Synthetic Rubber
Back Cushion/Polyurethane Foam
Clear White
6.5KG
W315xD280 X H1,150mm
30KG
Up to 15KG
For children from 5 months to 2.5 years of age (30 months)
Combi Baby Keep Fit F72
BK-F72
6
After checking, assemble in the reverse procedure.
When assembling, make sure that lower cover fixing
screws (2 locations) and plastic caps (2 pcs.) are not
missing or loosened.
After the assembly is completed, inspect it by
referring to the Daily Inspection (page 4).
Use a Phillips screwdriver No2 to check
the screws for concrete (2 locations). Use
Phillips screwdriver No3 to check anchor
bolts (2 locations) are missing or loosened.
Use a Phillips screwdriver No2 to
check 4 tapping screws are not
missing or loosened.
Use a flat-head screwdriver to remove
2 plastic caps, and then use a Phillips
screwdriver No3 to remove 2 screws
securing the lower cover.
A. Checking Attachment / Detachment and Looseness of Various Screws
(when Combi Corner Bracket F31 (hereinafter, Corner Bracket) is not used)
❶Checking Anchor Bolt
❷Checking Tapping Screws, Concrete Screws, and Anchor Bolts.
❸Checking Lower Cover Fixing Screw.
*Corner bracket is
sold separately.
Periodic inspection is conducted periodically once a year.
● If any abnormalities are found during inspection, immediately stop using the product and contact your dealer
to request repair.
2Periodic Inspection
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❶Anchor bolts (3 locations)
❷When installed on a partition
Tapping screws (4 locations)
When mounted on concrete or ALC
Screws for concrete (2 locations)
Anchor bolts (2 locations)
❸Bottom cover fixing screws (2 locations)
Retightening
Retightening
Retightening
Visual, Touch
(Wrench (nominal 17MM)
Visual
(Phillips screwdriver No2, No3)
Visual
(Phillips screwdriver No3)
No missing or looseness
No missing or looseness
No missing or looseness
①
Remove the back cushion. For
disassembly the back cushion,
refer "Back Cushion Replacement
Procedure" on the back cover.
①
Use a wrench (nominal 17MM) and
check the anchor bolts (3 locations)
are not missing or loosen.
②
Guard
Back Cushion
Main Body
Seat Pad
Lower Cover
Plastic Cap
Accessories *Make sure that the following parts are included:
● U-shape
Washer 3 pcs.
● Tapping Screw
(5X35) 4 pcs.
● Washer (5)
4 pcs.
● Usage S BL-07
Japanese, English,
Chinese, Korean
(hereafter, Usage
Sticker) 1 pc.
Anchor bolts are not included and it must be prepared separately.
● Failure to observe the above may result in death or serious injury to children.
Children may move unexpectedly.
Be careful not to cause accidents due to falling.
● Guidance S BK
Japanese, English,
Chinese, Korean
(hereafter, Guidance
Sticker): 2 pcs
● Instruction Manual
BK-F7 (this manual)
1 copy
● Installation
Manual BK-F7
1 copy
●
Plastic Cap White
(hereafter, Plastic
Cap) 2 pcs
● Seat Cushion with
BK-07 adhesive
(hereafter, Seat Pad)
1 pc.
● Pack of Back Cushion,
BK-F72 CW (hereafter
referred to as Back
Cushion) 1 pc.
When installed on a partition When mounted on concrete or ALC
Main body
Anchor bolts
(3 locations)
Tapping screws
(4 locations) Screws for concrete
(2 locations)
Anchor bolts
(2 locations)
Back cushion Back plate
Use Phillips screwdriver No3, flat-head screwdriver
Lower cover
Bottom cover fixing
screws (2 locations)
Plastic cap (2 pcs)
Bottom cover fixing
screws (2 locations)
Plastic cap
Lower
cover

4
Daily Inspection
Periodic Inspection
Daily or Weekly
Once a Year
Combi Baby Keep Fit F72
Inspection Manual
This manual describes the details of "Daily Inspection" and "Periodic Inspection" required to use Combi Baby Keep Fit
F72 safely and comfortably. Follow the contents of this manual and make sure to carry out the daily or weekly inspec-
tions and periodic inspection every year correctly.
Daily inspections are carried out by visual and touch.If any abnormality is found
in the inspection, use a tool to perform the inspection depending on the case.
Daily inspection should be carried out daily or weekly. Inspections are done by visual and touch.
If any abnormality is found in the inspection, use a tool to perform the inspection depending on the point.
● If any abnormalities are found during inspection, stop using the product and contact your dealer to request repair.
Warning Carry out daily inspection and periodic inspection once a year to ensure safety. Failure to do so may cause an injury or seri-
ous accident caused by undiscovered deterioration or damage to the product.
1
A. Checking the Appearance
②Looseness of the Guard
Make sure that there is no looseness in
the guard after shaking the guard to left
and right.
Phillips Screwdriver
No.2, No.3
Flat-Head Screwdriver Wrench (nominal 17MM) Do not use the power tool when fastening the
product. Make sure to tighten by hand and do
not use the power tool.
Any use of the power tool may result in damage
to the plastic part.
Required Tools Preparethefollowingtools. Caution
Each part is inspected every year using a tool.
As a result of the inspection, parts may need to be replaced.
*The stock period of the repair parts is 5 years after the final production.
Daily Inspection
C. Confirmation of Installation Environment
⑩
Guide S BK Readable all
Japanese, English, Chinese,
Korean
⑪
Guard S BK07 Readable
⑫
Main unit S BK07 Readable all
Japanese, English, Chinese,
Korean
⑬
Usage S BK07 Readable all
Japanese, English, Chinese,
Korean
Affix to the door of a toilet or
at the entrance
Affix to the front of
the guard
Affix to the front when the guard
is opened.
Affix to the position near
the product and easy to see.
*The main body stickers and instruction stickers contain safety
cautions and warnings for the safe use of this product.
B. Checking Stickers
Inspection Points Inspection Method Judgment Criteria Handling of Defects
⑩Guide S BK Readable all Japanese,
English, Chinese, Korean
⑪Guard S BK07 Readable
⑫Main unit S BK07 Readable all Japanese,
English, Chinese, Korean
⑬Usage S BK07 Readable all Japanese,
English, Chinese, Korean
Replacement
Replacement
Replacement
Replacement
Visual
Visual
Visual
Visual
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
Inspection Points Inspection Method Judgment Criteria Handling of Defects
⑭Installation Environment AdjustmentVisual
No garbage bins, handrails, or other objects
in the area where children's feet can reach.
5
Inspection Points Inspection Method Judgment Criteria
①Looseness of the main body
②Looseness of guard section
③Looseness of back cushion
Motion,
Visual and touch
Handling of Defect
Retightening (see page 6
of periodic inspection)
Motion,
Visual and touch
Motion,
Visual and touch
Motion,
Visual and touch
④Looseness of seat pad
⑤Detachment of plastic cap
⑥Scratches or breakage of the main body
⑦
Scratches or damage of the back cushion material
⑧Soil on main body
⑨Soil on back cushion material
Repair
Replacement
Replacement
Replacement
Repair
Replacement
Cleaning
Cleaning
Visual
Visual
Visual
Visual
Visual
No looseness when the main
body is being shaken.
When the guard is shaken by hand,
there should be no rattling.
When the back cushion is shaken by
hand, there should be no looseness.
When the seat pad is shaken by hand,
there should be no looseness.
No peeling or missing
No serious scratch or damage
No severe cut or damage
No soiling
No soiling

4
Daily Inspection
Periodic Inspection
Daily or Weekly
Once a Year
Combi Baby Keep Fit F72
Inspection Manual
This manual describes the details of "Daily Inspection" and "Periodic Inspection" required to use Combi Baby Keep Fit
F72 safely and comfortably. Follow the contents of this manual and make sure to carry out the daily or weekly inspec-
tions and periodic inspection every year correctly.
Daily inspections are carried out by visual and touch.If any abnormality is found
in the inspection, use a tool to perform the inspection depending on the case.
Daily inspection should be carried out daily or weekly. Inspections are done by visual and touch.
If any abnormality is found in the inspection, use a tool to perform the inspection depending on the point.
● If any abnormalities are found during inspection, stop using the product and contact your dealer to request repair.
Warning Carry out daily inspection and periodic inspection once a year to ensure safety. Failure to do so may cause an injury or seri-
ous accident caused by undiscovered deterioration or damage to the product.
1
A. Checking the Appearance
②Looseness of the Guard
Make sure that there is no looseness in
the guard after shaking the guard to left
and right.
Phillips Screwdriver
No.2, No.3
Flat-Head Screwdriver Wrench (nominal 17MM) Do not use the power tool when fastening the
product. Make sure to tighten by hand and do
not use the power tool.
Any use of the power tool may result in damage
to the plastic part.
Required Tools Preparethefollowingtools. Caution
Each part is inspected every year using a tool.
As a result of the inspection, parts may need to be replaced.
*The stock period of the repair parts is 5 years after the final production.
Daily Inspection
C. Confirmation of Installation Environment
⑩
Guide S BK Readable all
Japanese, English, Chinese,
Korean
⑪
Guard S BK07 Readable
⑫
Main unit S BK07 Readable all
Japanese, English, Chinese,
Korean
⑬
Usage S BK07 Readable all
Japanese, English, Chinese,
Korean
Affix to the door of a toilet or
at the entrance
Affix to the front of
the guard
Affix to the front when the guard
is opened.
Affix to the position near
the product and easy to see.
*The main body stickers and instruction stickers contain safety
cautions and warnings for the safe use of this product.
B. Checking Stickers
Inspection Points Inspection Method Judgment Criteria Handling of Defects
⑩Guide S BK Readable all Japanese,
English, Chinese, Korean
⑪Guard S BK07 Readable
⑫Main unit S BK07 Readable all Japanese,
English, Chinese, Korean
⑬Usage S BK07 Readable all Japanese,
English, Chinese, Korean
Replacement
Replacement
Replacement
Replacement
Visual
Visual
Visual
Visual
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
No peel off or damage of sticker are found
and the contents are readable.
Inspection Points Inspection Method Judgment Criteria Handling of Defects
⑭Installation Environment AdjustmentVisual
No garbage bins, handrails, or other objects
in the area where children's feet can reach.
5
Inspection Points Inspection Method Judgment Criteria
①Looseness of the main body
②Looseness of guard section
③Looseness of back cushion
Motion,
Visual and touch
Handling of Defect
Retightening (see page 6
of periodic inspection)
Motion,
Visual and touch
Motion,
Visual and touch
Motion,
Visual and touch
④Looseness of seat pad
⑤Detachment of plastic cap
⑥Scratches or breakage of the main body
⑦
Scratches or damage of the back cushion material
⑧Soil on main body
⑨Soil on back cushion material
Repair
Replacement
Replacement
Replacement
Repair
Replacement
Cleaning
Cleaning
Visual
Visual
Visual
Visual
Visual
No looseness when the main
body is being shaken.
When the guard is shaken by hand,
there should be no rattling.
When the back cushion is shaken by
hand, there should be no looseness.
When the seat pad is shaken by hand,
there should be no looseness.
No peeling or missing
No serious scratch or damage
No severe cut or damage
No soiling
No soiling

3
*Product specifications are subject to change without prior notice for product improvements.
*When disposing of the product, please dispose it properly in accordance with the local legislation of waste disposal.
*The dimensions and mass of the product are for reference only.
Product Specifications
4
Part Name
5
Product Life
Material
Color
Product Weight (Standard Specification)
External Dimensions
Maximum Load
Weight Limit
Target Age
Product Name
Product No.
How to Use
6
Warning Caution
Make sure to seat the child
by caregiver.
Be sure to use the product correctly according to the warnings below.
Keep eyes on
child all the time Do not leave Do not play with it No Fire
7 years Please replace the product after passing the product life.
Body/Steel (anti-rust treatment), ABS Plastic
Seat Pad/Synthetic Rubber
Back Cushion/Polyurethane Foam
Clear White
6.5KG
W315xD280 X H1,150mm
30KG
Up to 15KG
For children from 5 months to 2.5 years of age (30 months)
Combi Baby Keep Fit F72
BK-F72
6
After checking, assemble in the reverse procedure.
When assembling, make sure that lower cover fixing
screws (2 locations) and plastic caps (2 pcs.) are not
missing or loosened.
After the assembly is completed, inspect it by
referring to the Daily Inspection (page 4).
Use a Phillips screwdriver No2 to check
the screws for concrete (2 locations). Use
Phillips screwdriver No3 to check anchor
bolts (2 locations) are missing or loosened.
Use a Phillips screwdriver No2 to
check 4 tapping screws are not
missing or loosened.
Use a flat-head screwdriver to remove
2 plastic caps, and then use a Phillips
screwdriver No3 to remove 2 screws
securing the lower cover.
A. Checking Attachment / Detachment and Looseness of Various Screws
(when Combi Corner Bracket F31 (hereinafter, Corner Bracket) is not used)
❶Checking Anchor Bolt
❷Checking Tapping Screws, Concrete Screws, and Anchor Bolts.
❸Checking Lower Cover Fixing Screw.
*Corner bracket is
sold separately.
Periodic inspection is conducted periodically once a year.
● If any abnormalities are found during inspection, immediately stop using the product and contact your dealer
to request repair.
2Periodic Inspection
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❶Anchor bolts (3 locations)
❷When installed on a partition
Tapping screws (4 locations)
When mounted on concrete or ALC
Screws for concrete (2 locations)
Anchor bolts (2 locations)
❸Bottom cover fixing screws (2 locations)
Retightening
Retightening
Retightening
Visual, Touch
(Wrench (nominal 17MM)
Visual
(Phillips screwdriver No2, No3)
Visual
(Phillips screwdriver No3)
No missing or looseness
No missing or looseness
No missing or looseness
①
Remove the back cushion. For
disassembly the back cushion,
refer "Back Cushion Replacement
Procedure" on the back cover.
①
Use a wrench (nominal 17MM) and
check the anchor bolts (3 locations)
are not missing or loosen.
②
Guard
Back Cushion
Main Body
Seat Pad
Lower Cover
Plastic Cap
Accessories *Make sure that the following parts are included:
● U-shape
Washer 3 pcs.
● Tapping Screw
(5X35) 4 pcs.
● Washer (5)
4 pcs.
● Usage S BL-07
Japanese, English,
Chinese, Korean
(hereafter, Usage
Sticker) 1 pc.
Anchor bolts are not included and it must be prepared separately.
● Failure to observe the above may result in death or serious injury to children.
Children may move unexpectedly.
Be careful not to cause accidents due to falling.
● Guidance S BK
Japanese, English,
Chinese, Korean
(hereafter, Guidance
Sticker): 2 pcs
● Instruction Manual
BK-F7 (this manual)
1 copy
● Installation
Manual BK-F7
1 copy
●
Plastic Cap White
(hereafter, Plastic
Cap) 2 pcs
● Seat Cushion with
BK-07 adhesive
(hereafter, Seat Pad)
1 pc.
● Pack of Back Cushion,
BK-F72 CW (hereafter
referred to as Back
Cushion) 1 pc.
When installed on a partition When mounted on concrete or ALC
Main body
Anchor bolts
(3 locations)
Tapping screws
(4 locations) Screws for concrete
(2 locations)
Anchor bolts
(2 locations)
Back cushion Back plate
Use Phillips screwdriver No3, flat-head screwdriver
Lower cover
Bottom cover fixing
screws (2 locations)
Plastic cap (2 pcs)
Bottom cover fixing
screws (2 locations)
Plastic cap
Lower
cover

2
Warning
Caution
Application of Product
1
Safety Guidelines for Using the Product
2
Combi Baby Keep Fit F72
Instruction Manual
●Combi Baby Keep Fit F72 (hereafter referred to as "this product") is a chair dedicated for babies where children
can be seated with peace of mind. This product is intended for indoor use.
● If the Products is not used in compliance with the content of this instruction manual, it may cause a risk of injury to
the child or the user or a risk of property damage. The content related to safety is separated into Warnings and Cau-
tions depending on the severity of the risk. Read these guidelines before use and follow them to ensure safety.
Ignoring the instruction or misuse may result in severe injury or death.
Ignoring the instruction or misuse may result in injury or property damage.
Request to the Facility
3
Warning
Children may stand up and fall out.
● When installing the product, make sure that there is no object in the area where child's feet
may reach.
● Do not use the product other than the intended purpose.
If it is used by mistake or if a child plays with it, it may cause injury or serious accident.
● Do not leave the product needs repair.
If the inspections are not carried out, degradation or damage of the product may not be discovered,
which may cause injuries or serious accidents.
● Daily inspections and periodic inspections are required to ensure safe use of the product.
It may cause an unexpected accident.
● Do not modify the product.
For inspection methods, refer to the "Inspection Manual" on page 4 of this manual.
This product is intended for use with children seated. After installation, clean it regularly to keep it clean. Do not wash
with water. If it is soiled severely, wipe it off with diluted neutral detergent and wipe it off with a dry cloth again.
Cleaning Method
Caution
● Do not apply water to the product with a hose or apply extreme moisture. Corrosion of the compo-
nents may cause the product to fall off and it causes injury or serious accidents.
● Do not use detergents other than neutral detergents. The plastic may deteriorate, fade, or crack
and be damaged.
7
After the periodic inspection, enter the inspection
date on the inspection sticker affixed to the lower
cover.
D. Entering Inspection Date
B. Checking Missing or Loosening of Various Screws (when corner bracket is used)
C. Checking Appearance (Metal Parts)
After checking, assemble by the reverse procedure.
When assembling, make sure that anchor bolts (3 locations), main unit fixing screws (4 locations), and lower cover
fixing screws (2 locations) are not missing or loosened.
After the assembly is completed, inspect it by referring to the Daily Inspection (page 4).
❹ Checking Corner Cover Fixing Screws and Corner Bracket Fixing Screws.
❺ Checking Anchor Bolts, Body Fixing Screws, and Lower Cover Fixing Screws.
*The corner bracket is sold separately.
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❹
Corner cover fixing screws (2 locations)
Corner bracket fixing screws (4 locations)
❺
Anchor bolts (3 locations)
Main unit fixing screws (4 locations)
Bottom cover fixing screws (2 locations)
Retightening
Retightening
Visual, Touch
(Phillips screwdriver No2)
Visual, Touch
(Phillips screwdriver No3,
spanner (nominal 17MM))
No missing or looseness
Inspection Points Inspection Method Judgment Criteria Handling of Defects
❻
Deformation or rust of main body frame Discontinuation
of use
Visual No deformation or rust
❼
Missing, loss, deformation, rust of screws
and metal fittings ReplacementVisual No disconnection, loss,
deformation, or rust
No missing or looseness
Use a back cushion and a flat-head screwdriver to
remove the plastic caps (2 pcs), then use a Phillips
screwdriver No3 to remove the lower cover fixing
screws (2 locations ) and remove the lower cover.
*To disassemble the back cushion, refer to "Back
Cushion Replacement Procedure" on page 9.
①
Use a Phillips screwdriver No2 to check the
corner cover fixing screws (2 locations) and
corner bracket fixing screws (4 locations) are
not missing or loosened.
③
Using a Phillips screwdriver No3 to remove the main body
fixing screws (4 locations) and use wrench (nominal
17mm) to remove the anchor bolts (3 locations) driven
into the floor, and then remove the main body from the
corner bracket.
②
*The illustrations used in this manual may differ slightly from the product in order to provide an easy-to-understand explanation
of how to operate the product.
Main body
Corner bracket
Anchor bolts
(3 locations)
Body fixing screws
(4 locations)
Inspection sticker
(Inspection S for 1-year silver)
Use Phillips screwdriver No3 and wrench (nominal 17MM)
Corner bracket
Corner bracket
fixing screws
(4 locations)
Bottom cover fixing screws
(2 locations)
Plastic cap (2 pcs)
Bottom cover
Back cushion
Corner cover fixing
screws (2 locations)
Corner cover
Back side of
the main unit

Combi Baby Keep Fit F72
Instruction Manual • Inspection Manual
This document contains information that is required to use Combi Baby Keep Fit F72 safely and
comfortably. Read this manual thoroughly before use to ensure correct use and inspection of the
product. Please keep this manual carefully.
1
(A4) 133856040 190131(1)
This manual can also be downloaded (PDF) from the CombiWith
website. Please make the best use of it.
Chair for Babies "Baby Keep"
Save This Manual for Future Reference
Combi Baby Keep Fit F72
Parts Replacement Procedure Manual
After replacing parts, be sure to inspect
them in accordance with the contents of
"Daily Inspection" on page 4.
Warning
After replacing parts, be sure to inspect
them in accordance with the contents of
"Daily Inspection" on page 4.
Warning
After removing the seat pad, remove the
adhesive remaining on the main body com-
pletely. If a new seat pad is applied while
the adhesive remains, it makes it easier to
peel off.
Caution
After replacement, use the reverse procedure to install the back cushion.
Back Cushion Replacement Procedure
1Insert a flat-head screwdriver into
the insertion guide and lift the back
cushion.
(There is a guide for inserting at the
center of the bottom of the back
cush ion)
2Remove the lower part of the back
cushion from the back plate, and
pull the whole back cushion toward
you to remove it from the back
plate.
After replacement, install the seat pad using the reverse procedure.
If any abnormalities in the back cushion
are found, it is recommended to pur-
chase a back cushion to replace it using
the method shown on the right.
If any abnormalities in the seat pad are
found, it is recommended to purchase a
seat pad to replace it using the method
shown on the right.
Seat Pad Replacement Procedure
The seat pad is mounted with dou-
ble-sided tape.
Back cushion
Back plate
Seat pad
Back cushion
If any abnormality is detected during daily inspection or periodic inspection, and the parts are replaced with new ones.
Read this replacement procedure manual thoroughly to replace them correctly.