Infatrac WIAA-22 User manual

[phone]
[e-mail]
www.infatrac.com
UNPACKING INSTRUCTIONS
Your Wireless Industrial Alarm Adapter (WIAA) should
contain the following components:
Wireless Industrial Alarm Adapter (WIAA)
7-21vDC barrel plug to terminal block
Small Elbow Antenna
Security Cap
The following are sold separately
AC Power Supply
USB to Mini USB Programming Cable
RJ11 Phone Line
Extended Antenna
Signal Boosters
Figure 1: Rear Panel
Figure 2: Cable Pass Thru Security Cap
Figure 3: Security Cap Installed
SET UPINSTRUCTIONS
1. Pass the RJ11 Phone Cable and Power Cord through
the Security Cap Access Port.
2. Connect the Barrel Connector of the Power Plug to
the MS121a DC12V Power Port. Connect the Phone
Line to the Phone Line Port.
3. Unscrew the four (4) Screws from the Face Plate of
the MS121a. Attach the Security Cap over the Face
Plate and fasten the four (4) Screws to secure the
Security Cap in its locked position.
4. Attach the Antenna to the exposed ANT Port.
5. Connect the other end of the Phone and Power
Cables to your Fire Alarm Control Panel (FACP).
PROFESSIONAL INSTALLATION
RECOMMENDED
Contact [phone] if you would like us to
professionally install your MS121a.
Wireless Industrial Alarm Adapter
Quick Start Guide
Rev. A
Issue Date: 09012015
Document Number: 00102

[phone]
[e-mail]
www.infatrac.com
ACTIVATION INSTRUCTIONS
1. To activate your WIAA, contact Infatrac by calling our
toll free number 877-262-6593. You may be asked for
your WIAA’s MEID and Serial Number (S/N). You can
find these numbers on label located on the bottom of
your WIAA.
Figure 4: MEID and S/N
2. To register your WIAA, please visit
infatrac.com/registration-portal.html and fill out the
accompanying questionnaire.
3. To verify that your device has been activated, the
Internet Status LED (see table on HARDWARE STATUS
LEDs) should be lit. If it is not lit, please contact
customer support [phone]
4. Once your account is activated, you will receive your
welcome email containing your Sinapsium Subscription
Credentials.
FCC COMPLIANCE STATEMENT
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: "How
to Identify and Resolve Radio-TV Interference Problems." This booklet is
available from the U.S. Government Printing Office, Washington D.C.
20402.
Changes and Modifications not expressly approved by the manufacturer or
registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
HARDWARE STATUS LED’S
LED
ICON
COLOR
STATE
DESCRIPTION
1
POWER
STATUS
GREEN
ON
POWER ON
-
OFF
POWER OFF
2
SERVER
STATUS
-
OFF
MCU FAULT
AMBER
ON
SERVER
CONNECTED
3
INTERNET
STATUS
AMBER
ON
INTERNET “ON”
-
OFF
INTERNET “OFF”
4
SIGNAL
STATUS
AMBER
ON
STRONG SIGNAL
AMBER
FLASHING
WEAK SIGNAL
-
OFF
NO SIGNAL
5
BATTERY
DISCHARGE
INDICATOR
-
ON
BATTERY
CHARGING/NO
BATTERY
AMBER
FLASHING
BATTERY
DISCHARGEING
(6 Hour Battery
Standby)
6
BATTERY
CHARGING
INDICATOR
GREEN
ON
INTERNAL
BATTERY POWER
CONNECTED
-
OFF
BATTERY
DISCHARGEING/
BATTERY FULLY
CHARGED/NO
BATTERY
ADDITIONAL SUPPORT
INFORMATION
[e-mail]
[phone] Option 2
Complete Installation Manual can be found at:
https://www.infatrac.com/wireless-industrial-alarm-
adapter--wiaa-22.html