Ingco UCDLI218144 User manual
1
QUALITY INDUSTRIAL
YEAR
Li-ion
Cordless
Drill
CDLI218144
UCDLI218144
CDLI218180
UCDLI218180
produced & marketed
by
EN Li-ion
Cordless
Drill
2
English
Page
3-1
3
PRODUCT SPECIFICATION
Model Number
Drill voltage
Charging voltage
Charging time
Mechanical speed settings
No-load variable speed
Torque settings
Max torque force
Keyless chuck capacity
CDLI218144
14.4V
220~240V
~
50-60Hz
1Hr approx
2
0-400/0-1400rpm
23+1
23NM
0.8-10mm
UCDLI218144
14.4V
110~120
V~
60Hz
1Hr approx
2
0-400/0-1400rpm
23+1
23NM
1/32"-3/8"
Model Number
Drill voltage
Charging voltage
Charging time
Mechanical speed settings
No-load variable speed
Torque settings
Max torque force
Keyless chuck capacity
CDLI218180
18V
220~240V
~
50-60Hz
1Hr approx
2
0-400/0-1400rpm
23+1
35NM
2-13mm
UCDLI218180
18V
110~120
V~
60Hz
1Hr approx
2
0-400/0-1400rpm
23+1
35NM
5/64"-1/2"
4
PARTS IDENTIFICATION
T
orque
keyless
chuck
Drill mode selector
and torque setting
ring
setting
indicator
Cooling
vents
LED light
On/Off variable
speed trigger
switch
Directional
control switch
and safety lock
off button
Soft grip
handle
Battery
pack
CR-V Bit
5|English
SAFETY INSTRUCTIONS
WARNING!
Read all instructions.
Failure
to
follow
all
instructions listed
below
may result in electric shock, fire and/or serious injury. The term
“power tool”in all warnings listed below refers to your mains
operated (corded)
power
tool or battery operated (cordless) power
tool.
SAVE
THESE
INSTRUCTIONS
This product is not suitable for use by children, and may not be suitable for
persons
requiring
supervision
unless
theyreceive
instruction
by
acompetent
person on how to safely use the product.
1) Work area
a Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
b Do not operate power tools in explosive atmospheres, such as in the
presence
of
flammable
liquids,
gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce the risk of electric
shock.
b Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges or refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep the cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
e
When operating
a
power tool outdoors,
use
an extension cord
suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk
of electric shock.
6|English
SAFETY INSTRUCTIONS
3) Personal safety
a Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in personal injury.
b Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c
Avoid
accidental starting. Ensure the
switch
is
in
the
off
position
before
plugging
in. Carrying power tools with your finger on the switch or plugging
in power tools that have the switch on invites accidents.
d Removeany
adjusting
keyor
wrench
before
turning
the
powertool
on.
Awrench or a key leftattachedtoarotatingpartofthepower toolmay result
in personal injury.
e Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f Dress properly. Do
not
wear
loose
clothing
orjewellery. Keep
your
hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g If devices are provided for the connection of dust extraction and
collection
facilities,
ensure these are
connected
and
properly
used. Use
of these devices can reduce dust related hazards.
4) Power tool use and care
a Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate which it was designed.
b Do not use the power tool if the switchdoes not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d Store idle tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands of untrained users.
e Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power
tools
operation.
If
damaged,
have the
power
tool
repaired before
use. Many accidents are caused by poorly maintained power tools.
7|English
SAFETY INSTRUCTIONS
f Keep cutting tools sharp and clean. Poorly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g Use the power tool, accessories and tool bits etc., in accordance with
these
instructions
and
in
the manner
intended
for the particular type of
power
tool,
taking
into
account
the
working
conditions
and
the
work
to
be performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5) Battery tool use and care
a Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
b Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk of fire
when used with another battery pack.
c Use
power
tools
only
with
specifically
designated
batterypacks. Useof
any other battery packs may create a risk of injury and fire.
d When battery pack is not in use, keep it away from other metal objects
like paper
clips, coins,
keys,
nails,
screws, or other small
objects
that can
make a connection from one terminal to another. Shorting the battery
terminals together may cause burns or a fire.
e Underabusive
conditions,
liquid
may
be
ejectedfromthebattery;avoid
contact.
If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
6) Service
a Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
7) Operating
a Wear ear protectors with impact drills. Exposure to noise can cause
hearing loss.
8
OPE
RATINGINSTRUCTIONS
INSTALLING THE BATTERY PACK
WARNING!
Before removing, or insta ll ing a battery pack, make sure that the
directional control switch is in the central locked off position.
Directional Control switch in
locked off position
To install the battery pack, proceed as follows.
1 Align the grooves on bottom of the drill handle with the battery pack.
2 Push the battery pack into the drill until the battery ‘clicks’into position.
3 Make sure that the battery pack is fully located and clicks firmly into place
9
OPEARTING INSTRUCTIONS
REMOVING THE BATTERY PACK
To remove the battery pack, proceed as follows.
1 Press and hold the battery release button on the battery pack.
2 Draw the battery off the drill handle.
NOTE:
During use the battery maybecome hot. Allow it to cool downbefore
recharging .
2SPEED CHANGE
position 1 position 2
pull the button
10
OPEARTING INSTRUCTIONS
ADJUSTING THE TORQUE SETTING
The drill is fitted with a torque setting ring to vary the amount of torque
produced when drilling or screwdriving.
1 Select the setting by rotating the torque setting ring to align with the torque
setting indicator.
2 The torque is at minimum when setting 1 is selected and at maximum
when setting 23 is selected.
3 When the symbol is selected, the clutch is designed not to slip and
therefore most rotary drilling applications should be performed on this
setting.
4 To select the correct torque setting for screwdriving, first set the torque
setting ring to position 1.
5 Fit and tighten the first screw.
6 If the clutch starts to ratchet before the screw is correctly seated, rotate the
setting ring to a higher number until the clutch ratchets only when the head
of the screw is flush with the surface of the material.
7 The different settings are provided to vary the amount of torque available to
seat screws of different sizes in a variety of materials.
CAUTION!
Do not adjust the torque setting while the chuck is rotating.
Torquesetting ring
Torque setting indicator
11
OPERATING INSTRUCTIONS
USING
THEDIRECTIONAL
CONTROL
SWITCH
The direction control switch is used to alter the direction of rotation of the drill.
1 The direction of rotation is selected by moving the directional control
switch to either side of the drill.
2 For all drilling applications, the drill must be operated in the forward
direction.
3 If your drill bit jams whilst drilling, release the trigger switch.
4 When the drill has come to a complete stop, move the directional control
switch to the reverse position.
5 Press the trigger switch gently and the drill bit should then release.
6 Reverse direction should also be used for removing screws.
Direct ional control
swi t ch i n f orward
posi ti on
Direct ional control
swi t ch i n saf et y
l ocked of f posi t i on
Direct ional control
swi t ch i n reverse
posi t i on
WARNIN! G
Alwaysremembetro set the directional control switch to the central
locked off position whenthe drill is not being
u
se
d
or adjustments
are being
made.
This is an important safety feature and
must
be
ob
served.
12
OPERATING INSTRUCTIONS
OPERATING
THE
TRIGGER
SWITCH
WARNING!
Before operating the trigger switch, make sure that you have read
a
ll
o
ft
h
esafety
instructions on
pages 5to
7. Make sure that the
torque
setting has been selected to suit the material being drilled.
The trigger switch is used to start the drill. It also controls the speed at which
it operates.
1 Make sure that the directional control switch is positioned in either the
forward, or reverse position. The trigger switch will not operate if the
directional control switch is in the central locked off position.
2 Squeeze the trigger switch and the drill will start.
3 Chuck speed is increased by increasing the pressure on the trigger
switch.
4 Release the trigger switch to stop the drill.
The drill is fitted with an electric brake which stops the motor when the trigger is
released.
Trigger switch
13
USING THE DRILL
DRILLING
When drilling the following points should be observed.
1 Always use sharp, good quality drill bits. The performance of your drill is
dependant on the quality of the bits used.
2Reduce the pressure on the drill bit when it is about to break through. This
will prevent the drill from jamming.
3 If the drill bit does jam on breakthrough, release the trigger switch and
when the motor has come to a standstill, reverse the direction of rotation
and slowly operate the trigger switch.
4 If drilling a large hole, first drill a pilot hole using a smaller drill bit.
5 Always apply pressure to your drill bit in a straight line and, where
possible, at right angles to the workpiece.
6 When drilling holes or driving screws into walls, floors etc., always make
sure that there are no live electrical wires in the path of the bit.
7 When drilling in metal, the materials being drilled can become hot. To
reduce overheating use a suitable cooling lubricant. No cooling lubricant
is necessary when drilling cast iron or brass as they should be drilled dry.
8 To prevent the drill bit from slipping when starting to drill a hole in metal,
use a centre punch to make an indentation at the start point.
9 When drilling in wood, clamp a piece of scrap wood to the underside of
the material to avoid splintering.
10 Large holes should be drilled with wood augers, flat wood bits or hole
saws.
14
USING THE DRILL
SCREWDRIVING
When screwdriving the following points should be observed.
1 Place the point of the screwdriver bit in the head of the screw and apply light
pressure to the drill.
2 Start the drill slowly and then gradually increase the speed.
3 Release the trigger switch when the clutch operates.
4 Ifthe screw head is not flush with the material, increase the torque by adjusting
the torque setting ring and start again.
5 Make sure that the screwdriver bit is inserted straight and upright in the screw
head, or the screw may be damaged.
6 When driving wood screws, pre-drill pilot holes to make driving easier and to
prevent splitting the material.
7 Select forward rotation to drive screws in andreverse rotationto take themout.
CLEANING AND MAINTENANCE
WARNING!
Always remember
to
set the
directional
control
switch
to
thecentral
locked
off
position
and
remove the battery pack before
cleaning
the
drill.
After use, remove the drill or screwdriver bit, open the chuck jaws and tap the side
of the chuck to remove any dust, or chippings etc.
Keep the cooling vents clear.
Clean the motor housing with a soft cloth.
Keep the handles clean and free from oil and grease.
Keep the charger clean and free from dust and grease.
Worn or damaged parts must be replaced by qualified personnel.
There are no user serviceable parts inside the drill.
Refer to qualified service personnel if internal maintenance is required.
15
No.
Part Description
Qty
29
Planetary carrer
1
30
Planetary gear
5
31
Planetary carrer
1
32
Planetary gear
3
33
Fixed ring gear
1
34
Washer
1
35
Screw
2
36
Spring washer
2
37
Motor flange
1
38
Moter gear
1
39
Moter assembly
1
40
Tapping screw
4
41
Decoration plate
1
42
Left housing
1
43
Speed selector buttor
1
44
Level
1
45
Driver bit
1
46
FWD/REV lever
1
47
Switch assembly
1
48
Heat sink
1
49
Contact plate
1
50
Contact strip
2
51
Right housing
1
52
Tapping screw
10
53
Bit holder
1
54
Driver bit
1
55
Battery
1
CDLI218144,UCDLI218144,CDLI218180,UCDLI218180 Spare part list
No.
Part Description
Qty
1
Chuck screw
1
2
Chuck
1
3
Tapping screw
3
4
Compressing plate
1
5
Positioning spring
1
6
Torque setting ring
1
7
Inner threaded ring
1
8
Shaft
1
9
Axletree
1
10
Spring
1
11
Washer
4
12
Ball group
12
13
Shaft coat
1
14
Gear box
1
15
Washer
1
16
Snap ring
1
17
Washer
6
18
Shaft lock ring
1
19
Driving block
1
20
Needle roller
5
21
Gear ring
1
22
Planetary carrer
1
23
Planetary gear
4
24
Washer
1
25
H/L speed switch box
1
26
Tapping screw
4
27
2-speed lever
5
28
Moveable ring gear
1
.161
Englis
ißGCC DDIIIG
Vl
EW
CDLI218144 υCDLI218144 CDLI218180 υCDLI218180 Explodingview
17
CDLI218144,UCDLI218144
CDLI218180,UCDLI218180
4
2
1
3
This manual suits for next models
3
Table of contents
Other Ingco Drill manuals
