Ingersoll-Rand 2235TiMAX-2 User manual

User Manual of Product 1:
Ingersoll Rand 2235TiMAX 1/2” Drive Air Impact Wrench –
Lightweight 4.6 lb Design, Powerful Torque Output Up to 1,350
ft-lbs, Titanium Hammer Case, Max Control, Gray
User Manual of Product 2:
Ingersoll Rand 2115TiMAX 3/8” Drive Air Impact Wrench
–Powerful Reverse Torque Output Up to 1,350 ft/bs, 7 Vane
Motor, Light Touch Trigger, Max Control, Gray

47517268
Edition 4
September 2015
Save These Instructions
Product Information
EN Product Information
Especicaciones del producto
Spécications du produit
Προδιαγραφές προϊόντος
Especicações do Produto
Tuote-erittely
Produktspesikasjoner
Produktspecikationer
Produktspecikationer
Productspecicaties
Technische Produktdaten
Speciche prodotto
제품 상세
製品仕様
产品信息
Технические характеристики изделия
Informacje Macje o Produkcie
Ierices specikacijas
Gaminio techniniai duomenys
A termék jellemzői
Toote spetsikatsioon
Specikace výrobku
Информация за Продукта
BG
Informaţii Privind Produsul
RO
KO
JA
ZH
RU
PL
LV
LT
HU
ET
CS
SK
SL
EL
PT
FI
NO
SV
DA
NL
DE
IT
FR
ES
Špecikácie produktu
Specikacije izdelka Podaci o proizvodu
HR
Air Impact Wrench
2235MAX Series

2 47517268_ed4
4
75
32
1
9
6
48h
48h
PMAX
9
8h
24h
8
10
(Dwg. 47132782)
13
2
5
6
7
9
IR # - NPT IR # - BS inch (mm) NPT IR # IR # IR # cm3
C38341-810 C383D1-810 3/8 (10) 1/4 MSCF33 10P 105-1lb 4
10

47517268_ed4 EN-1
EN
Product Safety Information
Intended Use:
These Air Impact Wrenches are designed to remove and install threaded fasteners.
For additional information refer to Product Safety Information Manual Form 04580916.
Manuals can be downloaded from ingersollrandproducts.com
Power Management System
For models that include a power management system, the system allows operator reduction
of maximum output power in the forward direction. The power management system does not
aect the output power in the reverse direction.
To adjust the power, rotate the Power Regulator to the desired level indicator.
The power level indicators are for reference and DO NOT indicate a specic power. The power
output can be further reduced in forward or reverse by using the variable throttle.
Product Specications
Models Style
Drive Impacts
per
min.
Recommended
Torque Range
Type Size Forward
ft-lbs (Nm)
Reverse
ft-lbs (Nm)
2235TiMAX Pistol Square 1/2” 1220 900 MAX
(1220 MAX)
930 MAX
(1260 MAX)
2235TiMAX-2 Pistol Square
extended 1/2”x 2” 1220 900 MAX (1220 MAX)
930 MAX
(1260 MAX)
2235QTiMAX Pistol Square 1/2” 1220 870 MAX
(1180 MAX)
900 MAX
(1220 MAX)
2235QTiMAX-2 Pistol Square
extended 1/2”x 2” 1220 870 MAX (1180 MAX)
900 MAX
(1220 MAX)
2235PTiMAX Pistol Square
(Pin retainer) 1/2” 1220 900 MAX (1220 MAX)
930 MAX
(1260 MAX)
Models
Impacting Sound Level
dB(A)
(ISO15744)
Free Speed Sound Level
dB(A)
(ISO15744)
Vibration (m/s²)
(ISO28927)
† Pressure
(Lp)‡ Power (Lw) † Pressure (Lp) ‡ Power (Lw) Level *K
2235TiMAX 98.0 109.0 103.6 114.6 9.0 2.8
2235TiMAX-2 98.0 109.0 103.6 114.6 7.7 2.7
2235QTiMAX 91.9 102.9 88.7 99.7 9.0 2.8
2235QTiMAX-2 91.9 102.9 88.7 99.7 7.7 2.7
2235PTiMAX 98.0 109.0 103.6 114.6 9.0 2.8
† KpA = 3dB measurement uncertainty * K = Vibration measurement uncertainty
‡ KwA = 3dB measurement uncertainty

EN-2 47517268_ed4
EN
WARNING
Sound and vibration values were measured in compliance with internationally recognized
test standards. The exposure to the user in a specic tool application may vary from these
results. Therefore, on site measurements should be used to determine the hazard level in
that specic application.
Installation and Lubrication
Size air supply line to ensure tool’s maximum operating pressure (PMAX) at tool inlet. Drain
condensate from valve(s) at low point(s) of piping, air lter and compressor tank daily. Install a
properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose
coupling without internal shut-o, to prevent hose whipping if a hose fails or coupling discon-
nects. See drawing 47132782 and table on page 2. Maintenance frequency is shown in a circular
arrow and dened as h=hours, d=days, and m=months of actual use. Items identied as:
1. Air lter 7. Coupling
2. Regulator 8. Safety Air Fuse
3. Lubricator 9. Oil
4. Emergency shut-o valve 10. Grease - during assembly
5. Hose diameter 11. Grease - through tting
6. Thread size
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled,
degreased and parts be separated by material so that they can be recycled.
Original instructions are in English. Other languages are a translation of the original instructions.
Tool repair and maintenance should only be carried out by an authorized Service Center.
Refer all communications to the nearest Ingersoll Rand Oce or Distributor.