Innoband 8012-G1 User manual
ADSL2/2+ Modem
8012-G1
User’s Manual
Version 3.0
Last Revised: 07-16-2008
1. INTRODUCTION............................................................................... 14
........................................................................15IMPORTANT SAFETY INSTRUCTIONS
Model and Serial Numbers ................................................................................. 15
Minimum System Requirements......................................................................... 15
Package Contents................................................................................................ 16
................................................................................................17GETTING STARTED
.........................................................................18CUSTOMER INFORMATION RECORD
2. HARDWARE INSTALLATION........................................... 19
.........................................................................20ABOUT YOUR INNOBAND 8012-G1
......................................................................................22HARDWARE INSTALLATION
..................................................................................23CONNECTING MICROFILTERS
3. CONFIGURING YOUR COMPUTER........................... 24
...................................................25NETWORKING CONFIGURATION IN WINDOWS 2000
......................................................27NETWORKING CONFIGURATION IN WINDOWS XP
..................................................28NETWORKING CONFIGURATION IN WINDOWS VISTA
1. GO TO START -> CONTROL PANEL -> NETWORK AND INTERNET -> NETWORK AND SHARING
CENTER -> MANAGE NETWORK CONNECTIONS (SEE FIGURE 3-8) ............................................28
2. ...............................................28DOUBLE CLICK ON YOUR LAN OR HIGH-SPEED INTERNET
3. ............................28SELECT INTERNET PROTOCOL VERSION 4(TCP/IPV4) (SEE FIGURE 3-9)
4. ............................................................................................28CLICK PROPERTIES.
5. SELECT THE IP ADDRESS TAB.IN THIS PAGE,CLICK THE OBTAIN AN IP ADDRESS AUTOMATICALLY
RADIO BUTTON.(SEE FIGURE 3-10) ................................................................................29
6. SELECT OBTAIN DNS SERVER ADDRESS AUTOMATICALLY RADIO BUTTON AND CLICK OK TO FINISH
THE CONFIGURATION..................................................................................................29
2
..................................32CHECKING YOUR INNOBAND 8012-G1 DSL MODEM’S STATUS
4. INNOBAND SETUP WIZARD.............................................. 33
...........................................34OPENING INNOBAND 8012-G1’S CONFIGURATION PAGE
...................................................................................36USING THE STATUS OPTION
A. TECHNICAL SPECIFICATIONS......................................... 37
......................................................................38FACTORY DEFAULT SETTING VALUES
B. TROUBLESHOOTING................................................................... 39
........................................................................................39A. POSSIBLE PROBLEMS
......................................................................41B. INNOBAND 8012-G1 LED STATUS
........................................................................................41C. POSSIBLE PROBLEMS
C. FREQUENTLY ASKED QUESTIONS.............................. 43
D. GLOSSARY................................................................................................ 46
E. WARRANTY INFORMATION................................................. 52
REGISTRATION CARD........................................................................................53
FCC REGISTRATION INFORMATION FOR USERS ............................................54
CONTACT INFORMATION ...................................................................................55
3
USER MANUAL
Innoband 8012-G1
Information in this document is subject to change without notice and does not represent a
commitment on the part of Innoband Technologies, Inc. The software described in this document
is furnished under a license agreement and may be used or copied only in accordance with the
terms of the license agreement. It is
All contents are Copyright © 2006 Innoband, Inc. All rights reserved.
Manual Version 6.0
July 2008
Innoband is a trademark of Innoband Technologies, Inc. The trademarks, logos and service
marks (“Marks”) displayed on this manual are the property of Innoband or other third parties.
Users are not permitted to use these Marks without the prior written consent of Innoband or such
third party that may own the Mark. IBM is a registered trademark of International Business
Machines Corporation.Intel and Pentium are registered trademarks of Intel Corporation.Microsoft,
MS-DOS, Windows, and the Windows logo are registered trademarks of Microsoft Corporation.
All other products are trademarks or registered trademarks of their respective owners.
4
INNOBAND END-USER SOFTWARE LICENSE AGREEMENT
Version 2.6, March 2003
PLEASE READ THIS DOCUMENT CAREFULLY BEFORE INSTALLING THE SOFTWARE. BY
INSTALLING AND USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS OF
THIS AGREEMENT. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, DO
NOT INSTALL OR USE THE SOFTWARE. PROMPTLY RETURN, WITHIN 15 DAYS, THE
SOFTWARE, ALL RELATED DOCUMENTATION AND ACCOMPANYING ITEMS TO THE
PLACE OF ACQUISITION FOR A REFUND.
This is a legal agreement between you and Innoband Technologies, Inc. and its subsidiaries
("Innoband"). This Agreement states the terms and conditions upon which Innoband offers to
license the software sealed in the disk package together with all related documentation and
accompanying items including, but not limited to, the executable programs, drivers, libraries and
data files associated with such programs (collectively, the "Software").
LICENSE
1. Grant of License
The Software is licensed, not sold, to you for use only under the terms of this Agreement.
You own the disk or other media on which the Software is originally or subsequently recorded
or fixed; but, as between you and Innoband (and, to the extent applicable, its licensors),
Innoband retains all title to and ownership of the Software and reserves all rights not
expressly granted to you. The license under this Section 1 is conditioned upon your
compliance with all of your obligations under this Agreement. Innoband grants to you the right
to use all or a portion of this Software provided that:
(a) the Software is not distributed for profit;
(b) the Software is used only in conjunction with Innoband's family of products;
(c) the Software may NOT be modified;
(d) all copyright notices are maintained on the Software; and
(e) the licensee/end-user agrees to be bound by the terms of this agreement.
2. For Use on a Single Computer
The Software may be used only on a single computer by a single user at any time. You may
transfer the machine-readable portion of the Software from one computer to another
computer, provided that
(a) the Software (including any portion or copy thereof) is erased from the first computer
and
(b) there is no possibility that the Software will be used on more than one computer at a
time.
3. Stand-Alone Basis
You may use the Software only on a stand-alone basis, such that the Software and the
functions it provides are accessible only to persons who are physically present at the location
of the computer on which the Software is loaded. You may not allow the Software or its
functions to be accessed remotely, or transmit all or any portion of the Software through any
network or communication line.
4. Copyright The Software is owned by Innoband and/or its licensors and is protected by
United States copyright laws and international treaty provisions. You may not remove the
copyright notice from any copy of the Software or any copy of the written materials, if any,
accompanying the Software.
5
5. One Archival Copy You may make one (1) archival copy of the machine-readable portion of
the Software for backup purposes only in support of your use of the Software on a single
computer, provided that you reproduce on the copy all copyright and other proprietary rights
notices included on the originals of the Software.
6. No Merger or Integration You may not merge any portion of the Software into, or integrate
any portion of the Software with, any other program, except to the extent expressly permitted
by the laws of the jurisdiction where you are located. Any portion of the Software merged into
or integrated with another program, if any, will continue to be subject to the terms and
conditions of this Agreement, and you must reproduce on the merged or integrated portion all
copyright and other proprietary rights notices included in the originals of the Software.
7. Network Version If you have purchased a "network" version of the Software, this Agreement
applies to the installation of the Software on a single "file server". It may not be copied onto
multiple systems. Each "node" connected to the "file server" must also have its own license of
a "node copy" of the Software, which becomes a license only for that specific "node".
8. Transfer of License You may transfer your license of the Software, provided that
(a) you transfer all portions of the Software or copies thereof,
(b) you do not retain any portion of the Software or any copy thereof, and
(c) the transferee reads and agrees to be bound by the terms and conditions of this
Agreement.
9. Limitations on Using, Copying, and Modifying the Software. Except to the extent
expressly permitted by this Agreement or by the laws of the jurisdiction where you acquired
the Software, you may not use, copy or modify the Software. Nor may you sub-license any of
your rights under this Agreement. You may use the software for your personal use only, and
not for public performance or for the creation of publicly displayed videotapes.
10. Decompiling, Disassembling, or Reverse Engineering. You acknowledge that the
Software contains trade secrets and other proprietary information of Innoband and its
licensors. Except to the extent expressly permitted by this Agreement or by the laws of the
jurisdiction where you are located, you may not decompile, disassemble or otherwise reverse
engineer the Software, or engage in any other activities to obtain underlying information that
is not visible to the user in connection with normal use of the Software.
In particular, you agree not for any purpose to transmit the Software or display the Software's
object code on any computer screen or to make any hardcopy memory dumps of the
Software's object code. If you believe you require information related to the interoperability of
the Software with other programs, you shall not decompile or disassemble the Software to
obtain such information, and you agree to request such information from Innoband at the
address listed below. Upon receiving such a request, Innoband shall determine whether you
require such information for a legitimate purpose and, if so, Innoband will provide such
information to you within a reasonable time and on reasonable conditions.
In any event, you will notify Innoband of any information derived from reverse engineering or
such other activities, and the results thereof will constitute the confidential information of
Innoband that may be used only in connection with the Software.
11. For Software With CDDB Features.
This application may contain software from CDDB, Inc. of Berkeley, California d/b/a
Gracenote ("Gracenote"). The software from Gracenote (the "Gracenote CDDB Client")
6
enables the application to do online disc identification and obtain music-related information,
including name, artist, track, and title information ("Gracenote Data") from online servers
("Gracenote CDDB Servers") and to perform other functions. You may use Gracenote Data
only by means of the intended End User functions of the application software.
You agree that you will use Gracenote Data, the Gracenote CDDB Client, and Gracenote
CDDB Servers for your own personal non-commercial use only. You agree not to assign,
copy, transfer or transmit the Gracenote CDDB Client or any Gracenote Data to any third
party. YOU AGREE NOT TO USE OR EXPLOIT GRACENOTE DATA, THE GRACENOTE
CDDB CLIENT, OR GRACENOTE CDDB SERVERS, EXCEPT AS EXPRESSLY
PERMITTED HEREIN.
You agree that your non-exclusive license to use the Gracenote Data, the Gracenote CDDB
Client, and Gracenote CDDB Servers will terminate if you violate these restrictions. If your
license terminates, you agree to cease any and all use of the Gracenote Data, the Gracenote
CDDB Client, and Gracenote CDDB Servers. Gracenote reserves all rights in Gracenote
Data, the Gracenote CDDB Client, and the Gracenote CDDB Servers, including all ownership
rights. You agree that CDDB, Inc. may enforce its rights under this Agreement against you
directly in its own name.
The Gracenote CDDB Client and each item of Gracenote Data are licensed to you "AS IS."
Gracenote makes no representations or warranties, express or implied, regarding the
accuracy of any Gracenote Data in the Gracenote CDDB Servers. Gracenote reserves the
right to delete data from the Gracenote CDDB Servers or to change data categories for any
cause that Gracenote deems sufficient. No warranty is made that the Gracenote CDDB Client
or Gracenote CDDB Servers are error-free or that functioning of Gracenote CDDB Client or
Gracenote CDDB Servers will be uninterrupted. Gracenote is not obligated to provide you
with any new enhanced or additional data types or categories that Gracenote may choose to
provide in the future and is free to discontinue its online services at any time.
GRACENOTE DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE, AND NON-INFRINGEMENT. Gracenote does not warrant
the results that will be obtained by your use of the Gracenote CDDB Client or any Gracenote
CDDB Server. IN NO CASE WILL GRACENOTE BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES OR FOR ANY LOST PROFITS OR LOST REVENUES.
TERMINATION
The license granted to you is effective until terminated. You may terminate it at any time by
returning the Software (including any portions or copies thereof) to Innoband. The license will
also terminate automatically without any notice from Innoband if you fail to comply with any
term or condition of this Agreement. You agree upon such termination to return the Software
(including any portions or copies thereof) to Innoband. Upon termination, Innoband may also
enforce any rights provided by law. The provisions of this Agreement that protect the
proprietary rights of Innoband will continue in force after termination.
NO WARRANTY
Innoband does not warrant that the functions contained in the Software will meet your
requirements or that the operation of the Software will be uninterrupted, error-free or free
from malicious code. For the purposes of this paragraph, "malicious code" means any
program code designed to contaminate other computer programs or computer data, consume
computer resources, modify, destroy, record, or transmit data, or in some other fashion usurp
the normal operation of the computer, computer system, or computer network, including
7
viruses, Trojan horses, droppers, worms, logic bombs, and the like.
INDEMNIFICATION BY YOU
If you distribute the Software in violation of this Agreement, you hereby indemnify, hold
harmless and defend Innoband from and against any and all claims or lawsuits, including
attorney's fees and costs that arise, result from or are connected with the use or distribution
of the Software in violation of this Agreement.
THE SOFTWARE IS PROVIDED AS-IS WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
TITLE OR NONINFRINGEMENT. INNOBAND IS NOT OBLIGATED TO PROVIDE ANY
UPDATES, UPGRADES OR TECHNICAL SUPPORT FOR THE SOFTWARE.
Further, Innoband shall not be liable for the accuracy of any information provided by
Innoband or third party technical support personnel, or any damages caused, either directly
or indirectly, by acts taken or omissions made by you as a result of such technical support.
You assume full responsibility for the selection of the Software to achieve your intended
results, and for the installation, use and results obtained from the Software. You also assume
the entire risk as it applies to the quality and performance of the Software. Should the
Software prove defective, you (and not Innoband, or its distributors or dealers) assume the
entire cost of all necessary servicing, repair or correction.
Some countries/states do not allow the exclusion of implied warranties, so the above
exclusion may not apply to you. Innoband disclaims all warranties of any kind if the Software
was customized, repackaged or altered in any way by any third party other than Innoband.
LIMITATION OF REMEDIES AND DAMAGES IN NO EVENT WILL INNOBAND OR ITS
LICENSORS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, OR FOR ANY BODILY INJURY (INCLUDING DEATH) TO
ANY PERSONS CAUSED BY INNOBAND'S NEGLIGENCE, OR FOR ANY LOST PROFITS,
LOST SAVINGS, LOSS OF USE, LOST REVENUES OR LOST DATA ARISING FROM OR
RELATING TO THE SOFTWARE OR THIS AGREEMENT, EVEN IF INNOBAND OR ITS
LICENSORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO
EVENT WILL INNOBAND'S LIABILITY OR DAMAGES TO YOU OR ANY OTHER PERSON
EVER EXCEED THE AMOUNT PAID BY YOU TO USE THE SOFTWARE, REGARDLESS
OF THE FORM OF THE CLAIM.
Some countries/states do not allow the limitation or exclusion of liability for incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
PRODUCT RETURNS
IF YOU MUST SHIP THE SOFTWARE TO INNOBAND OR AN AUTHORIZED INNOBAND
DISTRIBUTOR OR DEALER, YOU MUST PREPAY SHIPPING AND EITHER INSURE THE
SOFTWARE OR ASSUME ALL RISK OF LOSS OR DAMAGE IN TRANSIT.
U.S. GOVERNMENT RESTRICTED RIGHTS
All Software and related documentation are provided with restricted rights. Use, duplication or
disclosure by the U.S. Government is subject to restrictions as set forth in subdivision
(b)(3)(ii) of the Rights in Technical Data and Computer Software Clause at 252.227-7013. If
you are sub-licensing or using the Software outside of the United States, you will comply with
the applicable local laws of your country, U.S. export control law, and the English version of
8
this Agreement.
CONTRACTOR/MANUFACTURER
The Contractor/Manufacturer for the Software is:
Innoband Technologies, Inc.
1921 Concourse Drive,
San Jose, CA 95035
GENERAL
This Agreement is binding on you as well as your employees, employers, contractors and
agents, and on any successors and assignees. Neither the Software nor any information
derived therefrom may be exported except in accordance with the laws of the U.S. or other
applicable provisions. This Agreement is governed by the laws of the State of California
(except to the extent federal law governs copyrights and federally registered trademarks).
This Agreement is the entire agreement between us and you agree that Innoband will not
have any liability for untrue statement or representation made by it, its agents or anyone else
(whether innocently or negligently) upon which you relied upon entering this Agreement,
unless such untrue statement or representation was made fraudulently. This Agreement
supersedes any other understandings or agreements, including, but not limited to,
advertising, with respect to the Software. If any provision of this Agreement is deemed invalid
or unenforceable by any country or government agency having jurisdiction, that particular
provision will be deemed modified to the extent necessary to make the provision valid and
enforceable, and the remaining provisions will remain in full force and effect.
For questions concerning this Agreement, please contact Innoband at the address stated
above. For questions on product or technical matters, contact the Innoband technical support
center nearest you.
This package may include software with DVD-Audio functionality for you to play content-
protected DVD-Audio discs. The functionality of this Software may be lost if the content
protection system is compromised. In this event, your sole remedy to restore such
functionality is to download a product update from Innoband’s website, of if you do not have
internet access, Innoband will use commercially reasonable means to provide replacement
software.
ADDENDUM TO THE MICROSOFT SOFTWARE LICENSE AGREEMENT
======================================================================
===========
IMPORTANT: By using the Microsoft software files (the "Microsoft Software") provided with
this Addendum, you are agreeing to be bound by the following terms. If you do not agree to
be bound by these terms, you may not use the Microsoft Software.
The Microsoft Software is provided for the sole purpose of replacing the corresponding files
provided with a previously licensed copy of the Microsoft software product ("ORIGINAL
PRODUCT"). Upon installation, the Microsoft Software files become part of the ORIGINAL
PRODUCT and are subject to the same warranty and license terms and conditions as the
ORIGINAL PRODUCT. If you do not have a valid license to use the ORIGINAL PRODUCT,
you may not use the Microsoft Software. Any other use of the Microsoft Software is
prohibited.
Nothing in this Agreement shall be construed on the part of Innoband as advocating or
authorizing the infringement of local and/or international laws applicable to your jurisdiction.
9
Decompilation
You agree not for any purpose to transmit the Software or display the Software's object code
on any computer screen or to make any hard copy memory dumps of the Software's object
code. If you believe you require information related to the interopretability of the Software with
other programs, you shall not decompile or disassemble the Software to obtain such
information, and you agree to request such information from Innoband at the address listed
earlier. Upon receiving such a request, Innoband shall determine whether you require such
information for a legitimate purpose and, if so, Innoband will provide such information to you
within a reasonable time and on reasonable conditions.
Limited Warranty
EXCEPT AS STATED EARLIER IN THIS AGREEMENT, AND AS PROVIDED UNDER THE
HEADING "STATUTORY RIGHTS", THE SOFTWARE IS PROVIDED AS-IS WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY,
QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, TITLE OR NONINFRINGEMENT.
Limitation of Remedy and Damages
THE LIMITATIONS OF REMEDIES AND DAMAGES IN THE SOFTWARE LICENSE
AGREEMENT SHALL NOT APPLY TO PERSONAL INJURY (INCLUDING DEATH) TO ANY
PERSON CAUSED BY INNOBAND'S NEGLIGENCE AND ARE SUBJECT TO THE
PROVISION SET OUT UNDER THE HEADING "STATUTORY RIGHTS".
Statutory rights
Irish law provides that certain conditions and warranties may be implied in contracts for the
sale of goods and in contracts for the supply of services. Such conditions and warranties are
hereby excluded, to the extent such exclusion, in the context of this transaction, is lawful
under Irish law. Conversely, such conditions and warranties, insofar as they may not be
lawfully excluded, shall apply. Accordingly nothing in this Agreement shall prejudice any
rights that you may enjoy by virtue of Sections 12, 13, 14 or 15 of the Irish Sale of Goods Act
1893 (as amended).
General
This Agreement is governed by the laws of the Republic of Ireland. The local language
version of this agreement shall apply to Software acquired in the EU. This Agreement is the
entire agreement between us, and you agree that Innoband will not have any liability for any
untrue statement or representation made by it, its agents or anyone else (whether innocently
or negligently) upon which you relied upon entering this Agreement, unless such untrue
statement or representation was made fraudulently.
Copyright Information for users of Innoband products
Certain Innoband products are designed to assist you in reproducing material for which you
own the copyright or are authorized to copy by the copyright owner or by exemption in
applicable law. Unless you own the copyright or have such authorization, you may be
violating copyright law and may be subject to payment of damages and other remedies. If you
are uncertain about your rights, you should contact your legal advisor. It is your responsibility
when using a Innoband product to ensure there is no infringement of applicable laws on
copyright whereby the copying of certain materials may require the prior consent of the
copyright owners. Innoband disclaims any liability with regard to any illegal use of the
Innoband product and Innoband shall in no event be liable with regard to the origin of any
data stored in a compressed audio file. You acknowledge and agree that the exportation or
use of MP3 Codecs in real-time broadcasting (terrestrial, satellite, cable or other media) or
broadcasting via Internet or other networks, such as but not limited to intranets etc., in pay-
10
Safety & Regulatory Information
The following sections contain notices for various countries:
CAUTION: This device is intended to be connected by the user to a CSA/TUV/UL
certified/listed IBM AT or compatible personal computers in the manufacturer’s
defined operator access area. Check the equipment operating/installation manual
and/or with the equipment manufacturer to verify/confirm if your equipment is suitable
for devices to be connected to it.
ATTENTION: Ce périphérique est destiné à être connecté par l’utilisateur à un
ordinateur IBM AT certifié ou listé CSA/TUV/UL ou compatible, à l’intérieur de la zone
d'accès définie par le fabricant. Consulter le mode d’emploi/guide d'installation et/ou le
fabricant de l’appareil pour vérifier ou confirmer qu'il est possible de connecter d'autres
périphériques à votre sytème.
Notice for the USA
FCC Part 15: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, this notice is not a guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try one or more of the following measures:
oReorient or relocate the receiving antenna.
oIncrease the distance between the equipment and receiver.
oConnect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
oConsult the dealer or an experienced radio/TV technician.
Caution
To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC
Rules, this device must be installed in computer equipment certified to comply with the
Class B limits.
All cables used to connect the computer and peripherals must be shielded and
grounded. Operation with non-certified computers or non-shielded cables may
result in interference to radio or television reception.
Modifications
12
Any changes or modifications not expressly approved by the grantee of this device could
void the user’s authority to operate the device.
Notice for Canada
This apparatus complies with the Class “B” limits for radio interference as specified in the
Canadian Department of Communications Radio Interference Regulations.
CET APPAREIL EST CONFORME AUX NORMES DE CLASSE “B” D’INTERFÉRENCE RADIO TEL
QUE SPÉCIFIÉ PAR LE MINISTÈRE CANADIEN DES COMMUNICATIONS DANS LES
RÈGLEMENTS D’INTERFÉRENCE RADIO.
13
1.INTRODUCTION
Welcome to Innoband Technologies, Inc World! Your new Digital Subscriber Line (DSL)
modem takes you to a world of digital entertainment and exploration by giving you fast
Internet connection through existing telephone lines.
Innoband 8012-G1 uses the most advanced “splitterless” Asymmetric DSL (ADSL)
technology that transforms ordinary telephone lines into broadband high-speed digital lines
for fast Internet access. Innoband 8012-G1 is compliant with both ITU G.Lite and G.DMT
standards that provides downstream data transmission up to 8 Mbps and upstream data
transmission up to 1 Mbps, depending upon your agreement with your DSL service provider.
This User Manual will help you during hardware installation, as well as setting up the
computer's networking configurations.
This section provides you with safety instructions and information you should know before
using your Innoband 8012-G1:
oImportant Safety Instructions
oModel and Serial Numbers
oMinimum System Requirements
oPackage Contents
oGetting Started
oCustomer Information Record
Introduction 14
Important Safety Instructions
This section provides basic safety information for your Innoband 8012-G1 ADSL 2/2+
modem.
Prior to using your modem, carefully read and understand the safety instructions. These
instructions must be followed to reduce the risk of fire, electric shock, or personal injury.
oMake sure that your modem is not exposed to direct sunlight or excessive heat radiation.
oKeep your modem at a place where there is minimum risk of spilling any liquid.
0
oThe surrounding ambient temperature must not exceed 40 C (1040F).
oAvoid humid conditions. Do not place the product near a water source or outlet such as a
bath tub, sink, wash bowl, laundry tub, swimming pool, rain, wet or humid wall, and so on.
oNever clean your modem with a damp cloth or use any liquid cleaner.
oDo not press, put any weight, or bend the power cord connected to a telephone
equipment.
oTo avoid risk of an electric shock during lightning, do not use any telephone equipment
that is connected to an electric socket.
oIn case of a gas leak, do not use any electric switch that is located in the vicinity of the
leak.
oTo report a gas leak, do not use any telephone equipment that is connected to an electric
power outlet in the vicinity of the leak.
oDo not use any electric product, electric cord, or power socket that is even partially
damaged.
oDo not expose yourself to dangerous voltages by opening the cover of your modem or
dismantling it.
oYou must not access the internal assembly or circuit board of your modem — none of its
parts are user replaceable.
oDo not dispose off the batteries in fire — they may explode and cause injury. Besides, you
must follow the local codes for special disposal instructions.
oIf your modem needs any service or repairs, only qualified service personnel must handle it.
Model and Serial Numbers
Your Innoband 8012-G1 has model and serial numbers. You can find it on the bottom of your
modem. Note down the model and serial numbers for future reference.
Minimum System Requirements
For a proper operation of your Innoband 8012-G1 ADSL 2/2+ Modem, refer to the minimum
system requirements listed below:
1.For your computer connected to the Ethernet port
•Intel Pentium 350 MHz or equivalent processor® ®
•Microsoft Windows 98 SE®
•30 MB of free hard disk space
•64 MB of RAM
•Installed Network Interface Card with an RJ-45 port
Introduction 15
Package Contents
Before you begin hardware installation, check your Innoband 8012-G1 package to ensure all
the following items are available:
•Innoband 8012-G1 ADSL 2/2+ Modem unit
•One CD-ROM that contains
a) Installation Driver
b) User Manual (PDF)
c) Acrobat Reader
•DC power adapter
•RJ-11 Phone cable (6 feet length)
•RJ-45 straight Ethernet cable (6 feet length)
•User Guide
•User Manual
•Innoband Microfilters (optional)
Introduction 16
Getting Started
Before you begin hardware or software installation and configuration, read this section carefully:
•You must sign up with a DSL service provider.
•Make sure that your telephone line has been enabled for the DSL service.
•Follow these steps to connect your 8012-G1 modem to your computer and Internet:
(a) Install the hardware as explained in Chapter 1: Hardware Installation.
(b) Configure your Innoband as explained in the Chapter 2: System Configuration Tool.
(d) Configure the computer’s Networking Properties as explained in the Chapter 3:
Configuring Your Computer.
(e) Start using your DSL line.
•If you face any problem or for any clarification, you should go through Appendixes on
Troubleshooting and Frequently Asked Questions.
Introduction 17
Customer Information Record
Keep a record of your DSL service information:
8012-G1 Product Registration
User ID and Password:
E-mail Address:
Outgoing Mail Server (SMTP):
Incoming Mail Server (POP3):
IP Address:
Subnet Mask:
Default Gateway:
Primary DNS Address:
Secondary DNS Address:
Virtual Path Identifier (VPI):
Virtual Channel Identifier (VCI):
Innoband’s IP Address** 192.168.1.1
Innoband’s Subnet mask** 255.255.255.0
Your IP Address during System 192.168.1.x
Configuration only** (x can have any value from 2 to 254)
HTML System Configuration Password 8012-G1
DSL Service Provider’s
Telephone number
*If your DSL service provider uses Dynamic Host Configuration Protocol (DHCP), then you will not be
provided with this information.
** This information is to be entered only when you are required to check your VCI/VPI settings.
You must not change these values, unless specifically asked by your service provider.
Introduction 18
2.HARDWARE INSTALLATION
This chapter provides information about your Innoband 8012-G1, as well as hardware installation.
To ensure the proper setup and performance, before you begin connecting cables and devices to
your Innoband 8012-G1, you must carefully go through the following sections:
oAbout Your Innoband 8012-G1
oHardware Installation
oConnecting Microfilters
Hardware Installation 19
About Your Innoband 8012-G1
Located at the rear panel of your Innoband 8012-G1(see Figure 1-1) are several connectors that
allow you to attach your computer and a telephone equipment, as shown in Figure 1-3.
Ethernet Port
PHONE Port DSL LINE Port Reset Button Power Connector
Figure 1-1: Rear panel of Innoband 8012-G1
PHONE port
Optional: Connect a telephone to the PHONE jack on your Innoband 8012-G1. Be sure to
connect a microfilter in series as shown in the Figure 1-2.
DSL LINE port
Using the RJ-11 phone cable, connect your DSL-enabled telephone line (the wall phone outlet) to
the DSL LINE jack located on your Innoband 8012-G1.
Note: This PHONE jack will work only for “splitterless” DSL line. If your service provider
has installed a splitter, then do not use the microfilters.
Ethernet port
Using the RJ-45 Ethernet cable, the Ethernet port connects your Innoband 8012-G1 to the
Ethernet Network Interface Card in a PC. You can also use the Ethernet port on Innoband 8012-
G1 to connect multiple computers through a hub. Then, you must use a proper Ethernet cable
(crossed or straight) depending upon the type of port on the hub.
Hardware Installation 20
Table of contents
