innovair Oasis WOE10C2DB1 / HOE10C2MR83 User manual
Oasis
INSTALLATION MANUAL
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
WOE10C2DB1 / HOE10C2MR83
WOE13C2DB1 / HOE13C2MR83
WOE18C2DB1 / HOE18C2MR83
WOE24C2DB1 / HOE24C2MR83
WOE36C2DB1 / HOE10C2MR1
MINI SPLIT SYSTEM
CONTENTS
SAFETY PRECA UTIONS
INSTALLATION INSTRUCTIONS
REFRIGERANT PIPE CONNECTION
ELECTRICAL WORK
TROUBLESHOOTING
&
0
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
SAFETY PRECAUTIONS
&
&
The items to be followed are classied by the symbols:
f & WARNING
1)
'
5)
7)
8)
9)
& CAUTION
1)
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
3
INSTALLATION INSTRUCTIONS
Selecting installation place
Read completely, then follow step by step.
Indoor unit:
Do not expose the indoor unit to heat or steam.
Select a place where there are no obstacles
in front or around the unit.
Make sure that condensation drainage can
be conveniently routed away.
Do not install near a doorway.
Ensure that the space on the left and right
of the unit is more than 12cm/4.72in.
Use a stud finder to locate studs to prevent unnecessary damage to the wall.
The indoor unit should be installed on the wall at a height of 2.3m/7.55ft or more from the floor.
The indoor unit should be installed allowing a minimum clearance of 15cm/5.9in from the ceiling.
Any variations in pipe length will/may require adjustment to refrigerant charge.
There should not be any direct sunlight. Otherwise, the sun will fade the plastic cabinet and
affect its appearance. If unavoidable, sunlight prevention should be taken into consideration.
Outdoor unit:
If an awning is built over the outdoor unit to
prevent direct sunlight or rain exposure,
make sure that heat radiation from the
condenser is not restricted.
Ensure that the clearance around the back
of the unit is more than 30cm/11.81in and left
side is more than 30cm/11.81in. The front of the
unit should have more than 200cm/78.74in of
clearance and the connection side (right side)
should have more than 60cm/23.62in of clearance.
Do not place animals and plants in the path of the air inlet or outlet.
Take the air conditioner weight into account and select a place where noise and vibration
will not be an issue.
Select a place so that the warm air and noise from the air conditioner do not disturb neighbors.
If the outdoor unit is installed on a roof structure, make sure unit is level.
Ensure the roof structure and anchoring method are adequate for the unit location.
Consult local codes regarding rooftop mounting.
If the outdoor unit is installed on roof structures or external walls, this may result in excessive
noise and vibration, and may also be classed as a non serviceable installation.
Rooftop installation:
Fig.2
Level gauge
Screwdriver
Electric drill,Hole core drill (φ90mm/3.54in)
Tools needed for installation:
Hexagonal wrench (4mm/0.157in)
Gas-leak detector (or a soapy spray)
User manual
Thermometer (no required, but recommended)
Multimeter (no required, but recommended) Measuring tape
Gloves for saftey (especially connecting line set)
Saftey goggles (especially connecting line set)
More than 2.3m/7.55ft
(from the floor)
More than 15cm/5.9in
(to the ceiling)
More than
12cm/4.72in
More than
12cm/4.72in
Fig.1
More than30cm/11.81in
More than
60cm/23.62in
More than
30cm/11.81in
More than 200cm/78.74in
>12cm/4.72in
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
INSTALLATION INSTRUCTIONS
Accessories
QTY
Fig.3
c
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
INSTALLATION INSTRUCTIONS
Indoor unit installation
1. Fitting the Installation Plate
Correct orientation
of Installation Plate
t
Fig.4
Fit the Installation Plate and drill
holes in the wall according to the
wall structure and corresponding
mounting points on the installation
plate.
c
A
c
I
I
I
�
pe
1 _
Fig.5
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
Important
INSTALLATION INSTRUCTIONS
Outdoor
Wall
!Indoor I
Connectors(both ends):
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
INSTALLATION INSTRUCTIONS
•
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
INSTALLATION INSTRUCTIONS
Ponding box
Pipe room
Connective
pipe
Wrapping belt
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
INSTALLATION INSTRUCTIONS
Outdoor unit installation
°
Outdoor unit
Refrigerant pipe
Curve
•
w
-
0 ¢
I
-
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
REFRIGERANT PIPE CONNECTION
4. Connecting the refrigerant pipe to outdoor unit
I
I
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
REFRIGERANT PIPE CONNECTION
After completing steps 1- 4, check that all the
connections are sealed correctly using leak
detection spray or soap suds. If any bubbles form,
the system has a leak and the screw connectors
must be retightened using an open-ended wrench.
5. Now remove the cover on the top valve using a
19 mm open-ended wrench. Open the valve by
turning it counter-clockwise as far as it will go
using a 5 mm Allen key. The valve is now open. If
the valve is not opened fully, the system may
malfunction and suffer damage. Screw the cover
back on to the top valve and tighten it well to
ensure that it is properly sealed. See Fig.24.
6. Now remove the cover on the bottom valve using
a 19 mm open-ended wrench. Open the valve by
turning it counter-clockwise as far as it will go
using a 5 mm Allen key. The valve is now open.
If the valve is not opened fully, the system may
malfunction and suffer damage. Screw the cover
back on to the bottom valve and tighten it well to
ensure that it is properly sealed. See Fig.25.
Fig.24
7. After completing steps 1-6, check that all the
connections are sealed correctly using leak
detection spray or soap suds. If any bubbles form,
the system has a leak and the screw connectors
must be retightened using an open- ended spanner.
8. Start the equipment so that the operating
pressures build up inside it. Check all the
connectors again for signs of leaks
a) during cooling mode
b) in heating mode.
If any bubbles form, the system has a leak and the
screw connectors must be retightened using an
open-ended wrench. I
Fig.25
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
ELECTRICAL WORK
Condenser Connection
Connection at the condesnser
slides over the spade.
Air Handler Connection
Air handler preconnected
at factory, no connection
needed.
+
Grounding Wire
Use screw to connect
to ground.
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
Test running:
Perform test operation after completing gas leak check at the flare nut connections and
electrical safety check.
Check that all tubing and wiring have been properly connected.
Check that the gas and liquid side service valves are fully open.
1. Connect the power, press the ON/OFF button on the remote controller to turn the unit on.
2. Use the MODE button to select COOL, HEAT, AUTO and FAN to check if all the functions
works well.
3. When the ambient temperature is too low(lower than 63 °F), the unit cannot be controlled by
the remote controller to run at cooling mode, manual operation can be taken. Manual
operation is used when the remote controller is disabledor maintenance is necessary.
Hold the panel sides and lift the panel up to an angle until it remains fixed
with a clicking sound.
Press the Manual control button to select the AUTO or COOL, the unit will
operate under Forced AUTO or COOL mode(see User Manual for details).
4. The test operation should last 30 minutes.
Manual control
button
AUTO/COOL
TEST RUNNING
Fig.27
Fig.28
14
Model A Model B
To indoor unit To indoor unit To power supply
To power supply
L1 L2 S L1 L2 L1 L2 S L1 L2
Terminal block of outdoor unit
To indoor unit To power supply
1(L) 2(N) S L N
13
Eletrical Specications
DIY-12 DIY-18 DIY-24 DIY-32
Power Supply
Min. Circuit Amps
Max Fuse
System
115/60/1 208-230/60/1 208-230/60/1 208-230/60/1
20.0A 4.0A 15.0A 16.0A
30.0A 20.0A 25.0A 25.0A
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
Troubleshooting
UON
i
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
Troubleshooting
Terminal block of indoor unit
Model B
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
Innovair Corporation
11490 NW 39th Street
Miami, FL 33178
www.innovair.com
©2015 Innovair Corporation. All Rights Reserved.
www.innovair.com
This manual suits for next models
4
Table of contents
Other innovair Air Conditioner manuals
innovair
innovair RI24C2D1 User manual
innovair
innovair PIN09H1V51 Instruction Manual
innovair
innovair INVERTER DELUXE Series User manual
innovair
innovair QUANTUM WIN12HV51 User manual
innovair
innovair Pure WP13C1DB1 User manual
innovair
innovair VWM0810H21 User manual
innovair
innovair BIN312C2V31 User manual
innovair
innovair VWM1320H21 User manual
innovair
innovair Inverter FLEX24 SEV2040H2R18 User manual
innovair
innovair ICS0736C21 User manual
innovair
innovair WOE10C2DB8 User manual
innovair
innovair Elite EIN10H2V32 Quick start guide
innovair
innovair MULTI-MAX VOM0847H7RE605 User manual
innovair
innovair BIN625C2V32 User manual
innovair
innovair QIN415H2V31 User manual
innovair
innovair 2nd Generation User manual
innovair
innovair IN312C2V31 User manual
innovair
innovair NEXXOS NIN413C2V33 User manual
innovair
innovair Elite EIN10H2V32 User manual
innovair
innovair IUS0736C21 User manual
Popular Air Conditioner manuals by other brands
Fujitsu
Fujitsu ASYG 09 LLCA installation manual
York
York HVHC 07-12DS Installation & owner's manual
Carrier
Carrier Fan Coil 42B Installation, operation and maintenance manual
intensity
intensity IDUFCI60KC-3 installation manual
Frigidaire
Frigidaire FAC064K7A2 Factory parts catalog
Sanyo
Sanyo KS2432 instruction manual
Mitsubishi Electric
Mitsubishi Electric PUHZ-RP50VHA4 Service manual
Panasonic
Panasonic CS-S18HKQ Service manual
Panasonic
Panasonic CS-E15NKE3 operating instructions
Gree
Gree GWH18TC-K3DNA1B/I Service manual
Friedrich
Friedrich ZoneAire Compact P08SA owner's manual
Daikin
Daikin R32 Split Series installation manual