innovair PIN09H1V51 Instruction Manual

PIN09H1V51
PIN09H2V51
PIN12H1V51
PIN12H2V51
PIN18H2V51
PIN24H2V51
Installation & User
Manual
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments
• Installation or repairs made by unqualified persons can resu t in hazards to you and others.
• Failure to carefully read and follow all instructions in thi manual can result in equipment
malfunction, property damage, personal injury and/or death.
• This service is only for service engineer to use
pÜre
)&"516.14:45&.

Operating Instructions...........................
7
Safety Precautions..................................
System Components................................
Indoor Unit Overview.............................
Indoor Unit Installation......................... 2
Maintenance Instructions.......................
INNOVAIR DC INVERTER XXXXXXXXX SERVICE MA NUAL
Contents
Outdoor Unit Installation......................
Troubleshooting......................................
A
Appendix..................................................
Model Reference
21
2
2
1
5
INNOVAIR DC INVERTER XXXXXXXXX
Service Manual

SAFETY PRECAUTIONS
To prevent personal injury, or property or unit damage, adhere to all
precautionary measures and instructions outlined in this manual.
Before servicing a unit, refer to this service manual and its relevant
sections.
Failure to adhere to all precautionary measures listed in this section
may result in personal injury, damage to the unit or to property, or in
extreme cases, death.
WARNING indicates a potentially hazardous situation which
if not avoided could result in serious personal injury, or death.
CAUTION indicates a potentially hazardous situation which if
not avoided could result in minor or moderate personal injury,
or unit damage.
1. In case of Accidents or Emergency
WARNING
•
•
• If the unit comes into contact with liquid, contact an
authorized service center.
• If liquid from the batteries makes contact with skin or
clothing, immediately rinse or wash the area well with clean
water.
• Do not insert hands or other objects into the air inlet or outlet
while the unit is plugged in.
• Do not operate the unit with wet hands.
• Do not use a remote controller that has previously been
exposed to battery damage or battery leakage.
CAUTION
• Clean and ventilate the unit at regular intervals when operating
it near a stove or near similar devices.
• Do not use the unit during severe weather conditions.If
possible, remove the product from the window before such
occurrences.
2. Pre-Installation and Installation
WARNING
•Use this unit only on a dedicated circuit.
•Damage to the installation area could cause the unit to fall
potentially resulting in personal injury, prop-erty damage, or
product failure.
•Only qualified personnel should disassemble, install, remove, or
repair the unit.
•Only a qualified electrician should perform electricalwork. For
more information, contact your dealer, seller, or an authorized
Innovair service center.
CAUTION
• While unpacking be careful of sharp edges around the unit as well
as the edges of the fins on the condenser and evaporator.
3. Operation and Maintenance
WARNING
• Do not use defective or under-rated circuit breakers.
• Ensure the unit is properly grounded and that a
dedicated circuit and breaker are installed.
• Do not modify or extend the power cable. Ensure
the power cable is secure and not damaged during
operation.
• Do not unplug the power supply plug during
operation.
• Do not store or use flammable materials near the unit.
• Do not open the inlet grill of the unit during operation.
•
•
•Do not use harsh detergents, solvents, or similar items o clean
the unit. Use a soft cloth for cleaning.
• Do not touch the metal parts of the unit when
• Do not step on or place anything on the unit or outdoor
units.
•Do not drink water drained from the unit
•Avoid direct skin contact with water drained from the unit.
•Use a firm stool or step ladder according to manufacturer
procedures when cleaning or
maintaining the unit.
CAUTION
• Do not install or operate the unit for an extended period of
time in areas of high humidity or in an environment directly
exposing it to sea wind or salt spray.
•Do not install the unit on a defective or damaged
installation stand, or in an unsecure location.
• Ensure the unit is installed at a level position
•Do not install the unit where noise or air discharge created by
the outdoor unit will negatively impact the environment or
nearby residences.
• Do not expose skin directly to the air discharged by
the unit for prolonged periods of time.
• Ensure the unit operates in areas water or other liquids.
• Ensure the drain hose is installed correctly to ensure
proper water drainage.
• When lifting or transporting the unit, it is recommended that
two or more people are used for this task.
• When the unit is not to be used for an extended time,
disconnect the power supply or turn off the breaker.
Do not touch the electrostatic filter if the unit is equipped
with one.
Do not block the inlet or outlet of air flow to the unit.
If strange sounds or smoke is detected from the unit, turn the
breaker off and disconnect the power supply cable.
If a gas leak is suspected, immediately turn off the gas and
ventilate the area if a gas leak is suspected before turning the
unit on.
CAUTION CAUTION
CAUTION
WARNING
CAUTION
CAUTION
CAUTION
WARNING
SAFETY PRECAUTIONS
Service Manual
w w w . i n n o v a i r . c o m

ºPay attention to such a situation.
Be sure not to do. Grounding is essential.
Warning: Incorrect handling could
cause a serious hazard,
Symbols in this Use and Care Manual are interpreted as shown below.
Do not use the power supply circuit
breaker or pull off the plug to turn it off
during operation. This may cause a fire
due to spark, etc.
Keep the power supply circuit breaker
or plug from dirt. Connect the power
supply cord to it firmly and correctly,
lest an electric shock or a fire break out
due to insufficient contact.
Use correct power supply in
accordance with the rating plate
requirement. Otherwise, serious
faults or hazard may occur or a
fire maybe break out.
Do not knit, pull or press the power supply
cord, lest the power supply cord be broken.
An electric shock or fire is probably caused
by a broken power supply cord.
Never insert a stick or similar obstacle
to the unit. Since the fan rotates at high
speed, this may cause an injury.
Do not repair the appliance by yourself.
If this is done incorrectly, it may cause an
electric shock, etc.
Turn off the appliance by remote control
firstly before cutting off power supply if
malfunction occurs.
It is harmful to your health if the cool air
reaches you for a long time. It is advisable
to let the air flow be deflected to all the room.
Prevent the air flow from reaching the gas
burners and stove.
Do not touch the operation buttons
when your hands are wet.
Do not put any objects on the outdoor
unit.
It is the user's responsibility to make the
appliance be grounded according to
local codes or ordinances by a licenced
technician.
OFF OFF
ON
ON
ON/OFF
MODE FAN
SWINGSLEEPSUPER
SMART IFEELDIMMER
TIMER ON TIMER OFFCLOCK
OONN
OOFFFF
SAFETY PRECAUTIONS Service Manual
Safety Precaution

T 3.15A 250V
T 20A 250V
A residual current device(RCD)with the rating of above 10mA shall be incorporated in the fixed wiring
according to the national rule
Warning: Risk of electric shock can cause injury or death: Disconnect all remote electric power
supplies before servicing .
The best length of the connecting pipe between the indoor unit and outdoor unit is less than 7.5
meters(24.6ft). It will affect the efficiency of the air conditioner if the distance longer than that
length.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
The batteries in remote controller must be recycled or disposed of properly. Disposal of Scrap
Batteries --- Please discard the batteries as sorted municipal waste at the accessible collection
point.
If the appliance is fixed wiring, the appliance must be fitted with means for disconnection from the
supply mains having a contact separation in all poles that provide full disconnection under
overvoltage category III conditions, and these means must be incorporated in the fixed wiring in
accordance with the wiring rules.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
The appliance shall be installed in accordance with local electrical safety regulations and National
Electrical Codes(NEC).
The air conditioner must be installed by professional or qualified persons.
The appliance shall not be installed in the laundry.
The Fuse of the unit:
Model
9K-12K(208/230V)
Fuse of Indoor unit
18K(208/230V)
24K(208/230V)
Fuse ot outdoor unit
T 3.15A 250V
T 3.15A 250V
To guarantee the unit work normally, please read the manual carefully before installation, and try
to install strictly according to this manual.
Do not let air enter the refrigeration system or discharge refrigerant when moving the air
conditioner.
Properly ground the air conditioner into the earth.
Check the connecting cables and pipes carefully, make sure they are correct and firm before
connecting the power of the air conditioner.
There must be an air-break switch.
After installing, the consumer must operate the air conditioner correctly according to this
manual,keep a suitable storage for maintenance and moving of the air conditioner in the future.
T 3.15A 250V
12K(115V) T 20A 250V
T 3.15A 250V
9K(115V) T 20A 250V
T 15A 250V
T 30A 250V
Safety Instructions
SAFETY PRECAUTIONS
Service Manual
w w w . i n n o v a i r . c o m
3

Preparation before use
Note
Preset
Safeguarding the environment
cord so that the appliance cannot be re-used.
For more detailed information on handling and recycling this product, contact your local authorities
who deal with the separate collection of rubbish or the shop where you bought the appliance.
Before using the air conditioner, be sure to check and preset the following.
• Remote Control presetting
Each tim e after the remote control is replaced with new batteries or is energized, re mote
control auto presetting heat pump.If the air conditioner you purchased is a Cooling Only one,
heat pump remote controller can also be used.
• Back -light function of Remote Control(optional)
Hold down any button on remote control to activate the back light. It automatically shuts off
10 seconds later.
Note: Back -light is an optional function.
• Auto Restart Presetting
The air conditioner has an Auto-Restart function.
Thi s m arkin g i ndicate s t ha t thi s p roduc t s houl d n o t be d ispose d w ith
othe r h ousehol d w aste s t hroughou t th ort h America . To p reven t
possibl e h ar m to t h e e nvironmen t or h uma n h ealt h f ro m u ncontrolle d
wast e d isposal , r ecycl e it r esponsibl y to p romot e t h e s ustainabl e
reus e of m ateria l r esources . To r etur n y ou r u se d d evice , p leas e u s e t h e
retur n a n d c ollectio n s ystem s or c ontac t th e r etaile r w her e t h e
produc t w a s p urchased .
The y c a n t ak e t hi s p roduc t fo r e nvironmenta l s af e r ecycling .
4
SAFETY PRECAUTIONS
Service Manual
• When charging refrigerant into the system, make sure to charge in liquid state,if the
refrigerant of the appliance is R410A.Otherwise, chemical composition of refrigerant
(R410A) inside the system may change and thus affect performance of the air conditioner.
• According to the character of refrigerant (R410A,the value of GWP is 2088), the pressure
of the tube is very high, so be sure to be careful when you install and repair the appliance.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid a hazard.
• The air conditioner must be installed by a professional engineer.
• The temperature of refrigerant circuit will be high, please keep the interconnection
cable away from the copper tube .

Interior of the Indoor Air Handler
In addition to the filters, the interior of the indoor unit itself as well as the inner coil should be
inspected every season. The front panel can be disconnected and removed from the top hinge
where the pegs connect. This will allow for easier inspection of the interior and behind the air
filters. The interior should be cleaned with damp cloth and neutral soaps. Do not use any sort
of aggressive solvents or detergents. Only a soft cloth that is lightly damp should be used.
Periodic Maintenance Is Essential for The System!
Maintaining the air conditioner will ensure that is stays efficient. Before carrying out any
sort of maintenance, always ensure that the power supply to the system is turned off.
Indoor Unit
Anti-Dust Filters (Clean once every 2 weeks)
1. Open the front panel by pulling outward
and upward at the indicated location.
2. Keep the front panel raised with one hand
and take out the air filters with the other.
3. The filters are washable and should be
cleaned with warm water (under 113°F).
4. Leave the filters to dry in a cool, dry place.
5. Keeping the front panel raised with one
hand, insert the air filters with the other.
6. Close the front panel.
Any electrostatic or deodorizing filters, if
installed, are not washable and should be
replaced once every 6 months.
Maintenance Instructions
BEFORE CLEANING OR MAINTENANCE
ALWAYS TURN OFF YOUR AIR CONDITIONER SYSTEM AND DISCONNECT ITS POWER SUPPLY
BEFORE PERFORMNG CLEANING OR MAINTENANCE. DO NOT SPRAY WATER DIRECTLY NEAR
THE INDOOR UNIT, AS IT CAN DAMAGE INSULATION AND ELECTRICAL COMPONENTS.
MAINTENANCE INSTRUCTIONS Service Manual
w w w . i n n o v a i r . c o m
5
Anti-Dust Filter

•
Cut off the power supply
Turn off the appliance
first before disconnecting
from power supply.
Grasp position "a" and
pull outward to remove the
front panel.
Wipe with a soft
and dry cloth.
Use soft moisture cloth
to clean if the front panel
is very dirty;
Never sprinkle
water onto the
indoor unit
Never use volatile substance such as
gasoline or polishing powder to clean
the appliance.
Reinstall and shut the front panel.
Reinstall and shut the front panel by
pressing position "b" downward.
1 2
1
3
2
3 4
5 6
Stop the appliance, cut off the
power supply and remove the air
filter. Clean and reinstall the air filter.
1. 0pen the front panel.
2. Press the handle of the filter gently
3. Grasp the handle and slide out the filter.
Close the front panel again.
II Clean the air filter every two weeks
If the air conditioner operates In an
extremely dusty environment.
It is necessary to clean the air filter
after using it for about 100 hours.
If the dirt is conspicuous,
wash it with a solution of
detergent in lukewarm water.
After cleaning, dry well in
shade.
Front panel maintenance
6
MAINTENANCE INSTRUCTIONS
Service Manual

Model Reference
Nomenclature
Indoor Unit Model Outdoor Unit Model Capacity (Btu/h) Power Supply
P
P12k
12k
18k
24k
P12 H 2 V 5 1
12 3 4 5 6 7 8
1— Brand
P= PÜRE
2— System Performance
=
=
3— Nominal Capacity
0=
12 =
4—System Type
C =
H =
5—Voltage
1 =
2 =
4 =
6—Compressor Type
=
V =
7—Installation Kit Length
0 =
3 =
5 =
8—Version
1 =
9—Unit Identication
=
=
MODEL REFERENCE Service Manual
w w w . i n n o v a i r . c o m
7

Outdoor unit
The figures in this manual are based on the external view of a standard model.
Consequently, the shape may differ from that of the air conditioner you have selected.
5. Pipes and Power
Connection Cord
6. Drain Hose
4. Front Panel
3. Horizontal Louvers
2. Air Filter
1. Remote Controller
ON/OFF
MODE FAN
SWING SLEEP SU PER
SMART IFEEL DIMME R
TIMER O N TIMER OFF CLOC K
NNOO
FFFFOO
1
5
6
2
3
4
Par t Name
Indoor unit
8
MODEL REFERENCE
Service Manual
System Diagram

Indoor Unit Overview
3
1254
4
2
3
No. Description
SymbolLED Icon
1
2
3
4
5
Indicates that the unit is currently powered onPOWER
SLEEP
TIMER
RUN
Temp. Display
Indicates that the system is currently in SLEEP mode
Displays the current set temperature or any error codes
Indicates that the TIMER function has been set
Indicates that the fan is currently on and running
The shape and position of switches and indicators may vary accordingtothe model, however the functions remain the same.
There may be variancesbetween the amount of digitsthat are shown on the remote (3) vs. the amount on the indoor unit (2).
Front Panel Display
Emergency Manual Button And Auto-Restart Function
Emergency
Button
Front Panel
Emergency Manual Button
If the remote controller fails to operate the system, proceed as follows:
• Open and lift the front panel up at an angle to gain access to the
emergency button.
• Press the manual button once to start the unit in COOL mode.
• Press the button again within 3 seconds to start the unitin HEAT mode.
• Press a 3rd time within 5 seconds to turn off the unit.
Auto-Restart Feature
This appliance is programmed with an auto-restart function.
In case of sudden power failure, the control module will remember the
settings configured before power loss.
When power is restored, the unit will restart automatically, and will be
set to the previous settings, which were preserved with this memory
function.
The emergencybutton is located at
the terminal block cover of the unit
under the frontpanel.
INDOOR UNIT OVERVIEW Service Manual
w w w . i n n o v a i r . c o m
9

Operating Instructions
The display and some features of the remote control may
vary accordingtothe model of the system.
The shape and positions of the buttons and indicators may
vary accordingtothe model of the system, but the features
and functionality would remain the same.
The unit will confirm the successful reception of each button
command withabeep.
Button Description
Turns the air conditioner on or off
Activates/deactivates the ECO feature
Configures the automatic on/off times
Toggles the system’s Sleep Mode
Turns the LED display on or off
Activates the swinging of the louver
Puts the system into silent mode
Activates the system’s Follow Me mode
Controls the 46°F “Away from Home”
freeze protection.
Decreases set temperature, set timing,
or navigates the functional menu
Increases set temperature, set timing,
or navigates the functional menu
Selects the mode of operation (Auto,
Cool, Dry, Fan, and Heat modes)
Configures the fan speed
(Auto, Low, Mid, and High)
Activates/deactivates the TURBO
feature, which allows the system to
reach set temperatures quicker
MODE
DISPLAY
SWING
MUTE
I FEEL
AH
TURBO
FAN
TIMER
SLEEP
ECO
Remote Buttons Overview
10
OPERATING INSTRUCTIONS
Service Manual

NOTE ON ILLUSTRATIONS
The illustrations in this manual are strictly for explanatory purposes. The actual display and some
functions of the remote controller may vary according to the model purchased.
Operating Instructions
No. Description
Icon
10
3
4
5
6
Battery
Auto Mode
Cooling Mode
Dry Mode
Fan Only Mode
7
8
9
Heating Mode
ECO Mode
Timer
Remote Controller LED Screen and Icons
No. Description
Icon
2
1
12
11
Temperature
Fan Speed
Mute Function
Turbo Mode
15
16
18
17
13
14
10
3
4 5 6 7 8
9
112
11
61 51
18 17 13
Up-Down Auto Swing
Left-Right Auto Swing
Sleep Function
Health Function
I Feel/Follow Me Mode
46°F Freeze Protection
2
14
Operating Instructions
w w w . i n n o v a i r . c o m
11
OPERATING INSTRUCTIONS
Service Manual

Operating Instructions
Depending on the system, the control type (Cooling Only or Heat Pump) must be set after a
battery swap is done. As soon as the batteries are inserted, the symbols and will begin
flashing. Operate as below:
• When the symbol is displayed, push any button to set the control type to Cooling Only.
• When the symbol is displayed, push any button to set the control type to Heat Pump.
The temperature display can be set to show degrees in either °C or °F by doing the following:
1. Press and hold the TURBO button for 5+ seconds to activate the change prompt.
2. Repeat this process once more to switch between °C and °F options.
3. Release the button, and the setting will be active after 5 seconds have elapsed.
Operating the Remote Controller Successfully and Safely
• Ensure no objects come between the remote controller and signal
receptor of indoor unit.
• Keep the remote at least 3 ft away from televisions and other
electrical appliances.
• Always direct the remote controller toward the air conditioner.
• Don’t leave the remote exposed to sunrays.
Replacement of Batteries
Remove the battery cover from the rear of the remote controller, by sliding it downward in
the direction of the arrow as depicted below. Install batteries according to the depicted
directions (+ and -) as shown on the remote controller. The cover then slides back into place.
Configuring Remote Controller Settings (some models)
Use 2xAAA batteries. Donot use re-chargeable batteries. Replace old batteries withnew ones of the same type when the
display isnolonger legible. Donot dispose of batteries as unsortedmunicipal waste. Disposal of such waste separately
for special treatment isnecessary. Ifthe system will not be used for along time, remove batteriesto prevent leakage.
Note: Ifthe remote control isused to set the control type toCoolingOnly, the heating function cannot be activatedin
systems with a heat pump. To modify or reset this setting, first remove the batteries and then reinstall and repeat.
Note
Please remove batteries to avoid
leakage damage when not
being used foralong time.
+
+
Signal
receptor
DISPLAY 3D HEAL THY
ON/OFF
SWING
FAN
TIMER SUPER
SLEEPMOD E
ECO
CLOCK
12
OPERATING INSTRUCTIONS
Service Manual

Operating Instructions
CAUTION
Regarding the Airflow of the Indoor Unit
The air that is pulled in by the fan (the “return air”) enters the
grille and is passed through the filter. It is then
cooled/dehumidified/heated through the heat exchanger.
The direction of the air output is manipulated up and down by the
motorized louver, and left to right via manually controlled vertical
deflectors. Some models may come with “dual-swing” capability,
which offers both a horizontal and vertical motorized air flow swing.
Controlling the System’s Airflow
1. Pressing the SWING buttons activate the louver.
• Press the button to trigger the horizontal flaps
to swing up and down. Press this button again to
stop swing movement at the current angle.
• Press the button to trigger the vertical flaps to
swing left and right. Press this button again to
stop swing movement at the current angle.
2. If the vertical deflectors (which are located
underneath the flaps) are adjusted manually,
they can be used to fix the airflow in a certain
vertical position before turning the system on.
Filter
Heat
Fan
• Do notmanipulate the louvers themselves
manually, orserious damage may occur.
•Deflector adjustments should bemade
onlywhen the system is switched off.
•Never poke fingers, sticks, orother
objects into the air inlet/outlet vents.
Horizontal
Flaps
Flap
Movement Vertical
Deflectors
w w w . i n n o v a i r . c o m
13
OPERATING INSTRUCTIONS
Service Manual

Operating Instructions
COOLING Mode
Cooling mode allows the air conditioner
to cool the room while also reducing
the humidity of the air in the room.
To put the system into cooling mode,
press the button until the symbol
appears on the remote’s display.
The and buttons can then be used to
set a temperature lower than that of the room.
HEATING Mode
Heating mode allows the air conditioner
to heat the room.
To put the system into heating mode,
press the button until the symbol
appears on the remote’s display.
The and buttons can then be used to
set a temperature higher than that of the room.
NOTE
In heating mode, the appliancewill periodically enter a defrostcycle, which is essential in order to clean frosting
off the condenser and recover heat exchangecapability. This process is normal and lasts for2-10 minutes.
During defrosting, the indoorunit’s fan will cease operation. After the cycleis completed, the system will resume
its normal heat modeoperation automatically.
14
OPERATING INSTRUCTIONS
Service Manual

Operating Instructions
DRY Mode
Dry mode is a limited function that can help
reduce the humidity/moisture of the room.
To put the system into dry mode, press the
button until the symbol
appears on the remote’s display.
An automatic preset of this mode is then
activated.
FAN-ONLY Mode
Fan-only mode is used to set the system to use
only air ventilation and no heating or cooling.
To put the system into fan-only mode, press
the button until the symbol
appears on the remote’s display.
AUTO Mode
Auto mode will let the system determine the
running configuration based on the set
temperature and the current room temperature.
To put the system into AUTO mode, press the
button until the symbol
appears on the remote’s display.
w w w . i n n o v a i r . c o m
15
OPERATING INSTRUCTIONS
Service Manual

Operating Instructions
Turning the Display On or Off
The LED display on the front panel of the
system can be turned on or off as desired.
To do so, press the button in order to
switch off the LED display on the front panel.
This button can be pressed again to turn the
LED display back on.
SLEEP Mode
Sleep mode is generally meant for periods of lower
cooling requirements, such as during typical sleeping
hours. This mode will result in decreased energy use,
and can only be activated via remote control.
After 10 hours in sleep mode, the air conditioner will
revert to the previously set mode.
To put the system into sleep mode, press the
button, and the symbol will appear on the display.
Press this button again to exit from this mode.
Changing the Fan Speed
The fan speed can be changed between
AUTO, LOW, MID, and HIGH speeds.
To do so, press the button. The running
fan speed can then be set.
16
OPERATING INSTRUCTIONS
Service Manual

Energy Saver (ECO) Option
In this mode, the appliance will automatically
manage the operation in order to save energy.
To turn the ECO feature on, press the
button on the remote, and the icon will
appear. The system is now running in ECO,
and the process can be repeated to turn it off.
Operating Instructions
NOTE
The ECO feature is available in both COOLING
and HEATING modes.
TURBO Option
In this mode, the appliance will operate using the
highest fan speed in order to maximize output
and reach the set temperature the quickest.
To turn the TURBO feature on, press the
button on the remote, and the icon will
appear. The system is now running in TURBO,
and the process can be repeated to turn it off.
w w w . i n n o v a i r . c o m
17
OPERATING INSTRUCTIONS
Service Manual

Using the Timer - TIMER ON
The TIMER feature allows you to set a time delay
for the system to turn itself on or off.
To set a time delay for the system to turn itself on
in X number of hours:
1. Begin by pressing the button while the
system is powered off. The symbol will then
display. You can then set the needed modes.
2. Set the desired mode (COOL, HEAT, AUTO,
FAN, DRY) by pressing the button.
3. Set the desired fan speed with the button.
4. Use the and buttons to set the desired
operation temperature.
5. Press the button again to set the switch-on
time. Use the and buttons to set the
needed time delay.
6. Press the button again to confirm. It can
also be pressed once more to cancel the setting.
Using the Timer - TIMER OFF
The TIMER OFF feature allows the appliance to
turn itself off after X number of hours have passed.
The symbol will appear. To set a time delay for
the system to turn itself off in X number of hours:
1. Confirm that the appliance is on and running.
2. Press the button to enter the prompt for
switching off the system. Use the and
buttons to configure the time delay setting.
3. Press the button again to confirm. It can
also be pressed once more to cancel the setting.
18
Operating Instructions
OPERATING INSTRUCTIONS
Service Manual