innovair Elite EIN10H2V32 User manual

HEAT PUMP
DUCTLESS SPLITS
OWNER'S
MANUAL
WARNING
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments
• Installation or repairs made by unqualified persons can result in hazards to you and others.
• Failure to carefully read and follow all instructions in this manual can result in equipment
malfunction, property damage, personal injury and/or death.
• This service is only for service engineer to use.
EIN10H2V32
EIN13H2V32
EIN18H2V32
EIN24H2V32

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SafetyPrecautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2- 3
Installation Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6
Operation of WirelessRemote Controller. . . . . . . . . . . . . . . . . .7-16
Operation of Smart Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20
Care and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Energy Saving Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back
Table of Contents
OWNER’S MANUAL
Innovair Elite Mini Split

NOMENCLATURE
Example: EIN10H2V32(I)
EIN 2
Series
EIN - Elite Inverter
Cooling Capacity
10 - 9,000 BTUH
13- 12,000 BTUH
18 - 18,000 BTUH
24 - 24,000 BTUH
1
OWNER’S MANUAL
Innovair Elite Mini Split
10 H
I- Indoor Unit
O- Outdoor Unit
2V
2V - 208/230V-1Ph-60Hz
Copper Kit Size (M)
3- 3 Meter Copper Kit
3 (I)

SAFETY PRECAUTIONS
Please read the following before operation.
Recognize safety information. This is the safety-alert symbol.When you see this
symbol on the unit and in instructions or manuals, be alert to the potential for personal
injury. Understand these signal words: DANGER, WARNING, and CAUTION. These
words are used with the safety-alert symbol.
DANGER identifies the most serious hazards which will result in severe personal injury
or death.
WARNING signifies hazards which could result in personal injury or death.
CAUTION is used to identify unsafe practices which may result in minor personal
injury or product and property damage.
NOTE is used to highlight suggestions which will result in enhanced installation,
reliability, or operation.
This appliance is not intended for use by children without responsible adult supervision.
Proper care should be taken to ensure safety.
Heat pumps, air conditioners & heating equipment should be installed, started up, and
serviced only by qualified installers and service technicians.Air conditioning, heat pumps
and refrigeration systems are hazardous due to high voltage electrical components,
high refrigerant pressures, and moving parts.
NOTE: Your actual air conditioning & heating system and related devices may differ
from the images shown in this manual.
WARNING
WARNING
2
OWNER’S MANUAL
Innovair Elite Mini Split

3
OWNER’S MANUAL
Innovair Elite Mini Split
SAFETY PRECAUTIONS
Please read the following before operation.
• Disconnect electrical power tothe indoor and outdoor units before performing any
maintenance or cleaning.
•Do not attempt torepair the Gree system yourself. Incorrect repairsmay cause
electric shock or fire. Contact aqualified service technician for all service requirements.
• Keep combustible materials away from the unit.
• Do not put hands or any objects into the air inlets or outlets. This may cause personal
injury or damage the unit.
• When cleaning, be careful not to splash water on the unit.Doing thismay cause
electric shock or damage to unit.
• Do not use or place any flammable, combustible or noxious substance next to the unit.
• In the event ofa failure (burning smell,etc.), immediately disconnect all electrical
power toindoor and outdoor units.
•
Never tryrepairing the system yourself; contact a qualified service technician for
all repairs.
WARNING
CAUTION

4
OWNER’S MANUAL
Innovair Elite Mini Split
Installation Schematic
Indoor unit
Installation Components*
1. Front Panel
2. Aux. Button
3. Filter
4. Horizontal Louver
5. Remote Controller
6. Inter-Connection Wire (sold separately)
7. DrainHose (sold separately)
8. Refrigerant Lines (sold separately)
Outdoor unit
5
Air outlet
Air inlet
Air inlet
Air outlet
3
4
1
2
6
7
8
* Not all items in this schematic are
included with equipment purchase

5
OWNER’S MANUAL
Innovair Elite Mini Split
SYSTEM FUNCTIONS
WHISPERQUIET
Not only are the systems energy efficient,but they are quiet too. Elite Wall Mount units operate
with sound lower than typical library sound levels.
MULTI FAN SPEEDS
Whether operating in either Cooling or Heating mode, the indoor fan can be set to your choice
of seven different speeds (Ultra-Low, Low, Low-Medium, Medium, Medium-High or High) to
achieve maximum comfort.
INTELLIGENT PRE-HEATING
The Elite system guards against the annoying cool air blown into the room in heating mode.
The system constantly monitors the discharge air temperature.It will delay the indoor fan until
the indoor coil has warmed up to prevent blowing uncomfortable cool air into the room.
I FEEL MODE
Senses the room temperature from the remote control (cooling mode only) which is closest to
you, instead of at the indoor unit.This means that it will adjust airflow and temperature for
maximum personal comfort.
SWING LOUVER
The unit has adjustable swing louvers which can be controlled from the wireless controller.
Vertical and horizontal swing louvers allows five different air discharge directions including
Continuous Sweep. Maximize comfort by adjusting the direction of airflow in the room by
moving the louvers up or down, right or left.
TIMER MODE
The unit can be programmed to turn ON or OFF after a specific amount of time. The time period
is adjustable between one half and 24 hours.
FREEZE GUARD
Room Freeze Guard protection will automatically keep the room temperature from getting too
cold, where water pipes might freeze.

6
OWNER’S MANUAL
Innovair Elite Mini Split
SYSTEM FUNCTIONS
MODEBUTTON
The unit can be set to five different operating modes: HEAT, COOL, DRY, FAN ONLY and AUTO.
NOTE:AUTO MODE has fixed setpoints of 68° Fheating and 77° F cooling, which are
not adjustable. The system will automatically select heating or cooling tomaintain room
temperature within this band.
SLEEP MODE
The Elite offers three selectable sleep modes for your comfort.The unit will automatically
adjust room temperature during your sleep time. This slight change in temperature will not
affect your comfort level due to the natural effects that sleeping has on the body, but it will
save on energy consumption and will lower electric bills.
X-FAN MODE
When operating in humid areas, Elite has a Dry Coil function that will allow the indoor fan to
run for a pre-determined amount of time after the unit is turned off (cooling or dry modes) to
ensure that additional moisture is removed from coil.
FAHRENHEIT °F / CELSIUS °C
The remote controller and Elite indoor wall unit displays can be set to display in either °F or °C.
LOCK MODE
The wireless remote controller has a Lock feature. The Lock averts unauthorized access or
tampering with system settings.
AGENCY LISTINGS
All systems are listed with AHRI (Air conditioning, Heating, and Refrigeration Institute) and
are ETL certified per UL Standards.

7
OWNER’S MANUAL
Innovair Elite Mini Split
Send Signal
Freeze Guard
Turbo Mode
Set time
X-FAN
TIMER ON /TIMER OFF
Privacy Lock
Up & Down Swing Louvers
Left & Right Swing Louvers
Fan Speed
Light
: Set Temperature : Indoor Room Temp.
: Outdoor Ambient Temp.
SleepMode
Clock
Heat Mode
Fan Mode
DryMode
Cool Mode
Auto Mode
Operation mode
I FEEL
Quiet
WIFI
Temp. display type
BUTTONS ON REMOTE CONTROLLER
INTRODUCTION FOR ICONS ON DISPLAY SCREEN
OPERATION OF WIRELESS REMOTE CONTROLLER
1. ON/OFF Button
2. Fan Button
3. Mode Button
4. +/- Buttons
5. TURBO Button
6. Button
7. Button
8. CLOCK Button
9. TIMER ON/
TIMER OFF Buttons
10. TEMP Button
11. I FEEL Button
12. LIGHT Button
13. X-FAN Button
14. QUIET Button
15. SLEEP Button
1. ON/OFF Button
2. Fan Button
3. Mode Button
4. +/- Button
(Before opening cover)
1
3
4
2
(After opening cover)
1
37
9
12
14
5
2
4
8
10 11
15
13
6

X-Fan Display
REMOTE CONTROLLER OPERATIONS
The wireless remote controller is sleek, versatile and allows you to change room
temperatures and functions on your Elite system from the palm of your hand. The large LCD
display and buttons make it easy-to-understand and easy-to-use.
The remote controller is set from factory to display temperatures in °F. If °C is desired, turn
the remote controller
OFF
with the
ON/OFF
button and then press “MODE“ and “
––
” buttons
on the remote simultaneously for 5 seconds.
ON/OFF BUTTON
When the system isin OFF mode, the remote controller will
display the time and last room setpoint. When you press the
ON/OFF button,the unit will start inthe last operating mode
and room setpoint.
NOTE: If the ON/OFF button ispressed too soon after a
stop, the compressor will not start for 3 to5 min. due tothe
inherent protection against frequent compressor cycling.
LOCK MODE
The Privacy Lock prevents unauthorized accessto the unit
controls and prevents tampering with system settings. The
remote controller can be locked bypushing the"+"and " – "
buttons simultaneously for 5 seconds. The Privacy Lock icon
will be displayed onthe remote controller. Repeat the process
to unlock the remote controller.
U
Privacy LockDisplay
OPERATION OF WIRELESS REMOTE CONTROLLER
ON Mode Display
X-FAN MODE
When operating in humid areas, the unit has a DRY COILfunction
called X-Fan that will allowthe indoor fan torun for apre-determined
amount oftime after the unit isturned off (cooling or drymodes)
to ensure that additional moisture isremoved from coil.Push the
“X-FAN”button to enable this feature. The X-FAN icon will
be displayed onremote controller. To deactivate this feature, push
the “X-FAN”button again.
8
OWNER’S MANUAL
Innovair Elite Mini Split

MODE BUTTON
Use the “MODE”button to select one of the available modes. The
selected mode will be displayed onthe remote controller and the
appropriate light will illuminate on the front display panel.
AUTO –Unit will automatically select heating or cooling to maintain
room temperature between 68°F and 77°F. The remote controller
will display the Auto Mode icon with no setpoint.The front panel
display will show "77."
COOL– To cool to selected setpoint and remove moisture.
System varies compressor speed tomaintain desired temperature.
HEAT – To heat to selected room setpoint.System varies compressor
speed to maintain desired room temperature.
FAN ONLY – To circulate air without heating or cooling. Use Fan Speed buttonto select
speed from lowto high.
DRY –Select DRY MODEto increase moisture removal during warm humid conditions.
1. If the Room Temperature is more than4°F above the set temperature, the system will
be operating in cooling mode withlow fan speed.
2. If the Room Temperature is between4°F higher than and 4°F less than the set
temperature, the system will cycle 6 minutes ON and 4 minutes OFFin cooling mode.
The indoor fan will be at low speed.
3. If the Room Temperature is more than 4°F belowthe set temperature, the system will
be OFF and the indoor fan will be at low speed.
: AUTO
: COOL
: DRY
:
FAN ONLY
: HEAT
Icons Displayed
OPERATION OF WIRELESS REMOTE CONTROLLER
TIMER SETTING
TIMER ON button
To set when you want the unit toturn On at the end ofa selected
time period, use the button labeled “TIMER ON on the remote
controller. Press thisbutton to make the clock icondisappear,
replaced withthe word “ON”(blinking). Press “+” or“ – ”buttons
to adjust timer setting 1minute
at atime. Press and hold “+”
or “
–
”buttonto set timer more quickly. Press“TIMER ON”button
again toconfirm setting, and the word “ON” will stop blinking.
To cancel,press“TIMER ON”button again.
Timer ON Display
9
OWNER’S MANUAL
Innovair Elite Mini Split

10
OWNER’S MANUAL
Innovair Elite Mini Split
Vertical Louver Display
Horizontal Louver Display
HORIZONTAL SWING LOUVERS
Press the Horizontal Swing Louver button to select continuous air
sweep left to right.The Swing Louver icon will be displayed.
Press this button again tocancel.
For fixed air direction mode, press the OFF buttontoturnthe unit OFF.
Press the Horizontal Swing Louver and the + buttons simultaneously
until the Horizontal Swing Louver icon flashes. Press the
ON button to turn the unit ON. Press the Horizontal Swing Louver
button to select air discharge direction as shown below:
OPERATION OF WIRELESS REMOTE CONTROLLER
VERTICAL SWING LOUVERS
Press the Vertical Swing Louver buttontoselect continuous air sweep
up and down.The Swing Louver iconwill be displayed.Pressthis
buttonagaintocancel.
For fixed air direction mode, press the OFF button to turnthe unit OFF.
Press the Vertical Swing Louver and the + buttonssimultaneously until
the Vertical Swing Louver icon flashes. Press the ON button to
turn the unit ON. Press the Vertical Swing Louver buttontoselect air
discharge direction as shown below:
I ndicates louver swings
up and down in the five
directions, as shown.
TIMER SETTING
TIMER OFF button
To set when you want the unit to turn Off at the end of a
selected time period,use the buttonlabeled “TIMER OFF”
on the remote controller. Press this button tomake the clock
icon disappear, replaced withthe word “OFF” (blinking).
Adjust settings the same as with “TIMER ON” settings.
NOTE: Under Timer Onand Off status, you can set TIMER
ON and TIMER OFF simultaneously. Before setting timer,
be sure to set clock to correct time.
Timer OFFDisplay

11
OWNER’S MANUAL
Innovair Elite Mini Split
OPERATION OF WIRELESS REMOTE CONTROLLER
TRADITIONAL MODE - SLEEP 1
In Traditional Mode the unit will slowly relax the room set temperature by up to
4° F until Sleep Mode iscancelled.
1
EXPERT MODE - SLEEP 2
In Expert Mode the unit will adjust the room set temperature at a rate based onthe starting
set temperature value. Sleep Mode will continue until cancelled.
2
Cooling ModeHeating Mode
Cooling Mode Heating Mode
SLEEP MODE
The Elite system will automatically adjust room temperature during
your sleep time. This slight change in temperature will not affect your
comfort level due to the natural effects that sleeping has on the body,
but it will save on energy consumption and will lower your electric bill.
The Elite system has three Sleep Modes to select from. Press the SLEEP
button to select Sleep 1, Sleep 2, Sleep 3 modes or Cancel.
The SLEEP icon will appear.
Sleep Mode Display

12
OWNER’S MANUAL
Innovair Elite Mini Split
OPERATION OF WIRELESS REMOTE CONTROLLER
NOTE: During this procedure, if no button ispressed within 10 seconds, remote controller
will automaticallyexit the sleep curve setting and resume original display. IfON/OFF, MODE
SLEEP, COOLING or HEATINGbutton ispressed during the setting or inquiryprocedure,
remote controller will also exit the sleep curve setting.
DIY MODE - SLEEP 3
You will be required toenter eight (8) room setpoint values for eight (8) hours of run time. The last
room setpoint value will be maintained until sleep mode iscancelled.
In Sleep Mode 3, press "Turbo" buttontoenter setup mode. The remote controller will display “1 hour”
in the time location.Use the “+” and “
–
“buttons to select the desired room setpoint for the first hour
of run time. Then press the “Prog” button to save the setpoint.
The remote controller time display will change to “2 hours.” Once again, use the “+” and “
–
“buttons
to select the desired room setpoint for the second hour of run time, and press the “Turbo” button to
again save the setpoint.
Repeat this sequence for the eight (8)room setpoint values. After all eight (8) values have been
entered,the remote controller will automaticallyrevert to standard time and temperature display,
and the Sleep 3Mode will begin.
At any time, you maypress the “ON/OFF," "Mode” or "Sleep” buttons tocancel
the Sleep 3 Mode.
LIGHTBUTTON
Press this buttonto turn off display light on indoor unit.
Press againto turn it back on.
Light Display

13
OWNER’S MANUAL
Innovair Elite Mini Split
OPERATION OF WIRELESS REMOTE CONTROLLER
TURBO MODE
The desired setpoint,either in heating or cooling,canbe achieved
faster if TURBOmode is used.After selecting the“HEAT” or
“COOL”mode button,push the “TURBO”button.The TURBO
icon will be displayed on the remote controller and the unit
will run at ultra high speed fan.To deactivate the feature, push the
“TURBO”button again.The unit will return to normal operation.
DISPLAYING SETPOINT OR INDOOR TEMPERATURE
ON FRONT PANEL:
The setpoint temperature or room temperature canbe displayed on
the front panel.Only setpoint temperature is displayed on the remote
controller.
When the “TEMP”button ispushed once, the temperature
indicator is displayed.Thisindicatesthat the setpoint temperature
is displayed on the front panel.
When the “TEMP”button ispushed a second time, the display will
show an icon witha thermometer inside a house. This indicates
that the room temperature is displayed on the front panel.
The room temperature will be displayed for only 5 seconds before
reverting back todisplaying room setpoint.
NOTE:
Onlyroom setpoint temperature will be displayed on
the remote controller.
Room Temperature Display
WIFIBUTTON
Press and hold boththe"Mode"and"Turbo" buttonsfor 10seconds
until the unit beeps for the second time and the WIFI icon appears
on the display. Repeat the procedure toturn WIFI mode OFF.
See“OperationofSmart Control”section for more information.
WIFI Display
Turbo Mode Display

14
OWNER’S MANUAL
Innovair Elite Mini Split
Quiet Mode Display
OPERATION OF WIRELESS REMOTE CONTROLLER
QUIET MODE
Sapphire’s QUIET MODE function delivers quiet comfort to your
room. Press QUIET button to activate QUIET MODE in heating
or cooling mode.The QUIET icon will be displayed on
the remote controller.The unit operates normally for ten (10)
minutes or until room setpoint temperature is reached.Then
the Elite system will operate quietly at Low fan speed.
Press QUIET button again to cancel QUIET MODE.
NOTE: QUIET MODE cannot be selected in DRY or FAN
ONLY modes.
Energy Saving Display
ENERGY SAVING MODE
The Elite System will not only keep you comfortable, they will
also save you money over the long run. Energy Saving
mode will automatically select the optimal fan speed to save
energy in COOL mode.The fan will automatically slow down
the closer the room temperature is to the setpoint. Press TEMP
and CLOCK simultaneously to activate Energy Saving mode.
The remote controller will display “SE”. Press TEMP and
CLOCK simultaneously to cancel Energy Saving Mode.
FREEZE GUARD
In Heat mode, press"TEMP"and "CLOCK" buttons simultaneously
to start up 46°F heating function. When this function is started up,
“46°F" will be displayed on the remote controller, and the unit
will maintain room temperature above 46°F. Press"TEMP" and
"CLOCK" buttons simultaneously again to cancel Freeze
Guard protection.
Freeze Guard Display

15
OWNER’S MANUAL
Innovair Elite Mini Split
OPERATION OF WIRELESS REMOTE CONTROLLER
CLOCKSETTING
Pressthis buttonto set clock time. “”icon on remote controller
will blink. Within 5 seconds, press “+” or “–” button to set clock
time. Witheachpressing of “+” or “–” buttons, clock time will
increase or decrease 1minute. To quickly adjust time setting, press
and hold “+”or “–”button for 2 seconds. Release button when
you have reached the desired time setting. Press “CLOCK” button
to confirm the time, and “ ”icon will stop blinking.
NOTE: Clock time adopts24-hour mode. A 12-hour format
is not available.
FAN BUTTON
Press the FAN button toadjust the fan circulation indoor speed:
Low ( ),Low-Medium (),Medium ( ), Medium-High ( ),
High ( ) and Auto.
I FEEL MODE
Press thisbutton to use the I FEEL function, and the () icon
will be displayed.The unit will sense room temperature at the
remote controller instead of at the indoor unit.It then adjusts
airflow and temperature accordingly for the ultimate inpersonal
comfort control and energy savings. Press the button again toexit
this function. For the best performance, keep the remote controller
withinan area where indoor unit can receive the signal sent by
the remote controller and away from heat or cold temperature
sourceswhile using this function.
I Feel Mode Display
Clock Setting Display
Fan Display

Remove
old batteries Install
new batteries
CHANGING BATTERIES
OPERATION OF WIRELESS REMOTE CONTROLLER
CHANGING BATTERIES AND ADDITIONAL NOTES
To change batteries, slide cover off battery compartment on back of remote controller. Remove
and safely discard old batteries. Insert two new AAA 1.5V dry batteries, using correct polarity.
Reattach back cover.
NOTE:
• If the remote controller will not be used for a long time, remove batteries to prevent
leakage damage.
• Be sure to aim the remote controller at the receiver of the main unit when operating.
• When remote emits a signal, icon will flicker; a tone will be heard when unit receives
that signal.
DAMAGED OR LOST REMOTE CONTROLLER
If remote controller is lost or damaged, the Elite system can be turned off directly from
the indoor unit. Lift the front panel of the indoor wall unit, then press the AUX button to
turn on or turn off. When the unit is on, it will operate in AUTO Mode.
Use insulated object to press the Aux. button.
WARNING
Aux. Button
Panel
16
OWNER’S MANUAL
Innovair Elite Mini Split

OPERATION OF SMART CONTROL
FOR USE WITH YOUR SMARTPHONE
For the ultimate in convenience, your Elite Heat Pump or Air Conditioner features a
built-in intelligent WIFI capability and Smart Control function. This allows you to
operate the unit through your smartphone. The system is compatible with devices
using standard Android or iOS operating systems.
Operating System Requirements for your smartphone:
iOS System supports iOS 7.0 and above.
Android System supports Android 4.0 and above.
STEP 1. Download and install (ZSH app on your smartphone
Scan this QR code to download the app directly from the Apple App Store
or the Google Play Store.
STEP 2. Turn ON the unit’s WIFI interface
Using the remote controller, turn ON the Elite system (making sure the
remote controller is paired). Press and hold the “TURBO”and “MODE”
buttons on the remote controller for at least 10 seconds until the unit
beeps for the second time and the WIFI icon appears on the display.
STEP 3. Launch the (ZSH app ON your smartphone
Open the app and follow its simple step-by-step instructions to register
your account and complete setup.
STEP 4.
Let the app be your guide
You are well on your way to controlling the unit through your smartphone.
You will find operation to be simple and easy, allowing you to adjust comfort
levels – even without the remote – from anywhere you have WIFI access.
COMMON NETWORK SETTING PROBLEMS
If WIFI control fails, check the following items one by one:
•
Make sure electrical power is turned on to the outdoor and indoor units.
•
Make sure WIFI function is turned On as normal
TO RESET WIFI MODULE
Press“TURBO”and “Mode” buttons simultaneously. When the Elite
unit emits a beep sound,WIFI module is successfully reset.
Get the app
17
OWNER’S MANUAL
Innovair Elite Mini Split

18
OWNER’S MANUAL
Innovair Elite Mini Split
TROUBLESHOOTING
PROBLEM
System does not restart.
Indoor unit emits unpleasant odor
when started.
You hear a“water flowing”sound.
A thin fog or vapor coming out
of the indoor unit when system is
running.
You hear a slight cracking sound
when the system stops or starts.
The system will not run.
The unit is not heating or cooling
adequately.
Water leakage from the
outdoor unit.
CAUSE/SOLUTION
Cause: The system has a built-in three-minute delay to prevent short and/or rapid
cycling of the compressor.
Solution: Wait three minutes for the protection delay to expire.
Cause: Typically unpleasant odors are the result of mold or mildew forming on
the coil surfaces or the air filter.
Solution: Wash indoor air filter in warm water with mild cleaner. If odors persist,
contact a qualified service professional to clean the coil surfaces.
Cause: It is normal for the system to make“water flowing”or“gurgling”sounds
from refrigerant pressures equalizing when the compressor starts and stops.
Solution: The noises should discontinue as the refrigerant system equalizes after
two or three minutes.
Cause: It is normal for the system to emit a slight fog or water vapor when
cooling extremely humid warm air.
Solution: The fog or water vapor will disappear as the system cools and
dehumidifies the room space.
Cause: It is normal for the system to make “slight cracking” sounds from parts
expanding and contracting during system starts and stops.
Solution: The noises will discontinue as temperature equalizes after 2 or 3 minutes.
Cause: There are a number of situations that will prevent the system from running.
Solution: Check for the following:
• Circuit breaker is “tripped” or “turned off.”
• Power button of remote is not turned on.
• Batteries in the remote controller are low.
• Remote controller is in sleep mode or timer mode.
• Otherwise, contact a qualified service professional for assistance.
Cause: There are a number of reasons for inadequate cooling or heating.
Solution: Check the following:
• Remove obstructions blocking airflow into the room.
• Clean dirty or blocked air filter that is restricting airflow into the system.
• Seal around door or windows to prevent air infiltration into the room.
• Relocate or remove heat sources from the room.
Cause: It is normal for the outdoor unit to generate condensate water in the
reverse cycle heating and defrost mode.
Solution: This is normal. No action is required.