Innovative PTS-04-LANE User manual

800.524.2744 InnovativeWorkspaces.com
PTS-04-LANE
Installation Instructions
© 2019 Innovative Office Products, LLC P514988 REV APAGE 1 OF 8

800.524.2744 InnovativeWorkspaces.com
PTS-04-LANE
Parts List
A T15 L-Key 1x
71490 4
B T20 L-Key 1x
714997
C T25 L-Key 1x
71489 9
D Lane Adapter Screw 2x
71430 5
E Lane Adapter Key 2x
114 3 0 7
PAGE 2 OF 8

800.524.2744 InnovativeWorkspaces.com
1
Optional grommet
hole for routing
cables below
mounting surface.
Mounting hardware
not included.
Use appropriate
hardware for your
mounting surface.
For above
surface cable
routing, route the
cable prior
to installing
the mount.
i
IMPORTANT:
Determine cable routing prior to
installing mount. This will ensure
the mount is installed in the correct
orientation for your installation.
Above Surface Cable Routing
Locate the mount cable exit and
plan your installation accordingly.
Below Surface Cable Routing
Cables may pass through the mount
(requires grommet hole).
Cable
Entry
Cable
Entry
Cable
Exit
Cable
Exit
PAGE 3 OF 8

800.524.2744 InnovativeWorkspaces.com
Placement of the two rotation stop screws in the outter
ring determine the amount of payment terminal rotation.
You can remove the screws from their original location
and place them in any of the holes in the outter ring to
allow for the amount of desired rotation.
There are rotation stop ribs underneath the top portion
of the mount that can be placed directly over the rotation
stop screw or pin. This positioning will prevent the payment
terminal from rotating. Determine the proper rotation stop
screw location for your installation.
T20
iROTATION STOP
CONFIGURATION
EXAMPLES
OR
ROTATION NO ROTATION
Rotation Stop Ribs
Place this area over
the rotation stop screw
or pin to prevent the
mount from rotating.
Rotation
Stop Pin
Rotation
Stop Screw
iNO ROTATION
CONFIGURATION
EXAMPLES
Rotation
Stop Screw
Rotation
Stop Screw
2a 2b
PAGE 4 OF 8

800.524.2744 InnovativeWorkspaces.com
3
iHOW TO RELEASE MOUNT
Release Tab
Locate the release tab inside the mount.
Using a screwdriver, or similar tool, pull back on
the tab. With the tab pulled back, lift up on the
upper portion of the mount to release.
When placing the top of the mount onto the base,
ensure the rotation stop ribs fall in between the
rotation stops that were set in place in Step 2.
Or in a no rotation conguration, the ribs must be
placed over top the rotation stop screw or pin.
PAGE 5 OF 8

800.524.2744 InnovativeWorkspaces.com
4a
4b
T15
T15
PAGE 6 OF 8

800.524.2744 InnovativeWorkspaces.com
5a
5b
5c
5a Push the adapter key down.
5b With the key pushed down, pull the key back.
5c With the key pushed back, slide payment
terminal onto mount.
Once the payment terminal is successfully
attached to the mount, the key can be returned
to its original position or removed to lock the
payment terminal on the stand.
iADAPTER KEY
The Lane adapter key (item E), needs to be
inserted in the mount in order to attach and
detach the payment terminal.
PAGE 7 OF 8

800.524.2744 InnovativeWorkspaces.com
6
OR
iADJUSTMENT FEATURE
To adjust the tilt friction, remove the hex nut covers
and tighten or loosen the 13mm hex nut while securing
the pivot screw on the inside of the mount with a
14mm wrench. Adjust both sides as needed.
13 m m
14 m m
PAGE 8 OF 8