INPRO 200/G2-200 Wall Guard User manual

Please read all instructions before installing
wallguard.
IPC.339/REV.8
Installation Instructions
200/G2-200 Wall Guard
Safety Glasses, Tape Measure, 3/8” socket for machine screw hex bolt, 7/16”socket for wood screw
hex bolt Level, Power Drill, Drill Bits - 1/4” masonry (concrete/concrete block), Power Miter Saw, 1O”
Blade with 60-80 Carbide Tipped Teeth
Recommended tools
Important
1. Acclimate materials 24 hrs
before installation. Maintain
temperature controlled
environment after installation
2. Install in accordance with
manufacturer’s installation
instructions. Failure to do so
will void the warranty.
Installation tips
1. Cut covers up to 1/16”(1.6mm)
longer to ensure a tight t.
2. Lubricate blades when cutting
aluminum to reduce burrs.
#10 x 1 3/4"
SHEET METAL
SCREW WITH
ALLIGATOR
ANCHOR
.080" (2mm)
VINYL COVER
CONTINUOUS
ALUMINIUM
RETAINER
.080" (2mm)
1 1/8"
[29mm]
1 1/8"
[29mm]
SECTION VIEW

Please read all instructions before installing
wallguard.
Wall Condion
Specified Fasteners
Inpro Part #
Profile Hardware Kit
HWK-WG/CR
Corner Hardware Kit - Concrete
HWK-CC
Corner Hardware Kit - Drywall
HWK-CDW
#10 x 1 3/4” Phillips Pan Head Sheet Metal Screw and 1/4” Alligator Anchor x2
#8 x 1 1/2” Phillips Indented Hex Washer Self Drilling Screw
#10 x 1 3/4” Phillips Pan Head Sheet Metal Screw and 1/4” Alligator Anchor x6
COMPONENTS AND FASTENERS
200
CONTINUOUS
METAL RETAINER
200V
VINYL COVER
201
END CAP
207
INSIDE CORNER
202
OUTSIDE CORNER
1/4"
ALLIGATOR
ANCHOR
#10 x 1 3/4"
PHILLIPS PAN HEAD
SHEET METAL SCREW
#8 x 1 1/2"
PHILLIPS INDENTED HEX
WASHER SELF DRILLING
202135
OUTSIDE CORNER
135°
Installation Instructions
200/G2-200 Wall Guard

Please read all instructions before installing
wallguard.
FIELD DIMENSIONS
(TYPICAL ALL WALLS)
1 1/8"
[28.6mm]
OUTSIDE CORNER
6 ANCHORS SPACED
EVENLY PER 12' LEGTH
(GIVEN 4" MAX ON
EITHER END)
~27"
[686mm]
INSIDE
CORNER
MAX FIRST
BRACKET
LOCATION
FROM WALL
4"
[102mm]
RETURN
DISTANCE TO
BE DETERMINED
BY INSTALLER
1 1/8"
[28.6mm]
135° OUTSIDE
CORNER
DISTANCE TO BE
DETERMINDE BY
INSTALLER (TYP)
LAYOUT VIEWS
Installation Instructions
200/G2-200 Wall Guard

Please read all instructions before installing
wallguard.
207 INSIDE CORNER
200 CONTINUOUS
ALUMINUM RETAINER
201 END CAP
#8 x 1 1/2"
PHILLIPS INDENTED HEX
WASHER SELF DRILLING
#10 x 1 3/4"
PHILLIPS PAN HEAD
SHEET METAL SCREW
200V CONTINUOUS
VINYL COVER
202 OUTSIDE
CORNER
1/4" ALLIGATOR
ANCHOR
EXPLODED ASSEMBLY
Installation Instructions
200/G2-200 Wall Guard

Please read all instructions before installing
wallguard.
DRILL 4"
FROM
EACH END
FOR ANCHORS
SPACE REMAINING
HOLES EVENLY
OVER 12' LENGTH
TOTAL OF 6 ANCHORS
PER 12' LENGTH
FIG. 1
FIG. 2
Please read all instructions before installing wall guard.
1. Cut aluminum retainer to desired length, leaving
allowance for end caps, inside corners and outside
corners. See Figure 1.
2. Drill holes in centerline of retainer using 1/4" [6mm]
drill bit. Position retainer on wall allowing for end caps/
corners. Level and mark holes. See Figure 2.
NOTE: For concrete or brick wall installation, drill 1/4"
[6mm] holes 3/8" [10mm] from each end of retainer for
end caps/corners.
CONTINUOUS
ALUMINUM RETAINER, .080”
OUTSIDE CORNER, 90˚
(
3
/16 " ALLOWANCE)
RETAINER
BUTT JOINT
END CAP
(1 1/4 " ALLOWANCE)
INSIDE CORNER
(1 9/16
" ALLOWANCE)
OUTSIDE CORNER, 135º
(1/16
" ALLOWANCE)
Installation Instructions
200/G2-200 Wall Guard

Please read all instructions before installing
wallguard.
FIG. 3
FIG. 4
3. Drill marked holes on wall using a 1/4" [6mm] drill
bit and position Alligator anchors into holes. Mount
retainer on wall and tighten screws to secure. Slide
end caps and corners onto the retainer and secure,
leaving a
1/16" [1.5mm] gap between end caps/corners and
retainer to allow for adjustment. See Figure 3.
NOTE: For concrete or brick wall installation, use #10
x 1 3/4" Phillips pan head screws to secure end caps
and corners.
4. Cut the cover to length between end caps and/
or corners. (Note: Trim factory edges square before
installation). Position cover on retainer and adjust
end caps and/or corners for a tight fit. Starting at
one end, push cover onto retainer until it snaps into
place. See Figure 4.
#10 x 13/4"
SHEET METAL
SCREW WITH
ALLIGATOR ANCHOR
R
#8 x 11/2" PHILLIPS
INDENTED HEX
WASHER SELF
DRILLING SCREW
COVER,
.080"
Installation Instructions
200/G2-200 Wall Guard