Southern Enterprises CM5071 User manual

1
CONSOLE

2
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer .
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study
the screw diagrams below. You may receive extra hardware with your unit.
※
Top supports up to 85 lb, per drawer supports up to 10 lb, per cabinet / compartment
/shelf supports up to 20 lb.
1.
Wood Dowel
∅6mmx25mm
Quantity Of 36
2.
Cam Bolt
Quantity Of 32
3.
Screw
∅3mmx12mm
Quantity Of 34
4.
Cam Lock
Quantity Of 32
5.
Cap
Quantity Of 32
6.
Bolt
∅6mmx28mm
Quantity Of 20
7.
Allen Wrench
Quantity Of 1
8.
Screw
∅3mmx18mm
Quantity Of 8
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the surface
with rough or abrasive objects.
Tool required: Phillips screw driver
(Not Included)
Assembly I nstructions
C ONSOLE
For replacement parts or
questions, please call our
Customer Service

3
LOCK
DOWEL
PARTS LIST:
NO DESCRIPTION QTY NO DESCRIPTION QTY
ABottom Panel (Lower Open Storage) 1NDrawer Back Panel 2
B Side Panel (Lower Open Storage) 2ODrawer Left Panel 2
C Center Divider (Lower Open Storage) 2P
Drawer Right Panel
2
DTop Panel (Lower Open Storage) 1QDrawer bottom Panel 2
E Back Panel (Lower Open Storage) 1 R Left Drawer Front Panel 1
FBottom Panel (Upper Drawer Unit) 1SRight Drawer Front Panel 1
GLeft Side Panel (Upper Drawer Unit) 1
HCenter divider (Upper Drawer Unit) 1
IRight Side Panel (Upper Drawer Unit) 1
JTop Panel (Upper Drawer Unit) 1
KBack Panel (Upper Drawer Unit) 1
L Metal Leg 2
MMetal Cross Brace 4
CAM LOCK INSTRUCTION
CAM LOCK INSTRUCTION:
PANEL I THIS ITEM IS ASSEMBLED WITH CAM LOCK SET.
--SCREW CAM BOLT INTO PANEL II.
--INSERT CAM LOCK INTO PRE-DRILLED HOLE IN PANEL I, AND
CAM LOCK
--ROTATE CAM LOCK UNTILARROW IS IN LINE WITH HOLE ON PANEL EDGE.
--ALIGN CAM BOLT TO CAM LOCK HOLE ON PANEL I, AND PRESS PANELS I &
II T OGETHER.
--LOCK PANELS TOGETHER BY TURNING CAM LOCK CLOCKWISE UNTIL
TIGHT.
PANEL II
CAM BOLT
NOTE :
FOLLOW INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE
FAST, EASY AND CORRECT ASSEMBLY. HOUSE HOLD GLUE SUGGESTED FOR WOOD DOWEL.(eg.
ELMERS GLUE, NOT PROVIDED).SOLID ARROW MARK POINTS AT FRONT SIDE OR UP DIRECTION.
PHILLIP SCREW DRIVER IS REQUIRED (NOT PROVIDED).TWO PERSONS ARE RECOMMENDED TO
ASSEMBLE THIS ITEM.
CONSOLE

4
Step 1:
Screw Cam Bolts (2) into the
Bottom Panel (A) and Top
Panel (D) of the Lower open
storage unit as shown in
Figure 1.
Step 2:
Assemble the Top Panel
(D), Side Panels (B), Center
Dividers (C) and the Bottom
Panel (A) by inserting Wood
Dowels (1) and Cam Bolts
(2) into their
corresponding holes until
all panels meet. Insert the
Cam Locks (4) and turn
them clockwise to tighten as
shown in Figure 1.
Figure 1
CONSOLE
Assembly Instructions

5
Step 1:
Tighten the Back Panel (E)
to the lower open storage
unit using Screws (3) as
shown in Figure 2.
Step 2:
Screw Cam Bolts (2) into
the Bottom Panel (F) and
Top Panel (J) of the upper
drawer unit as shown in
Figure 2.
Assemble the Top Panel (J),
Left Side Panel (G), Center
Divider (H), Right Side Panel
(I) and the Bottom Panel (F)
by inserting Wood Dowels (1)
and Cam Bolts (2) into their
corresponding holes until
all panels meet. Insert the
Cam Locks (4) and turn
them clockwise to tighten as
shown in Figure 2.
Figure 2
Step 3:
Tighten the Back Panel (K)
to the lower open storage
unit using Screws (3) as
shown in Figure 2.
CONSOLE
Assembly Instructions

6
Step 1:
Assemble the Metal Legs (L)
and Metal Cross Braces (M)
using Bolts (6) and provided
Allen Wrench (7) as shown
in Figure 3.
Step 2:
Position the upper drawer
unit and t he lower open
storage unit with metal leg
structure as shown in Figure
3.
Figure 3
CONSOLE
Assembly Instructions

7
Step 1:
Tighten the upper drawer unit
and the lower open storage unit
to the metal leg structure using
Bolts ( 6) and provided Allen
Wrench (7) as shown in Figure 4.
Step 2:
Assemble Drawer Left Panel (O),
Drawer Right Panel (P), Drawer
B ac k Panel (N) and Drawer
Bottom Panel (Q) using Screws
(8) as shown in Figure 4. Repeat
this step for another drawer.
Step 3:
Screw Cam Bolts (2) into the
Left Drawer Front Panel (R) and
Right Drawer Front Panel (S) as
shown in Figure 4.
Step 4:
Figure 4
Attach the Left Front Panel
(R) to the drawer assembly
by inserting Wood Dowels (1)
into their corresponding holes
until the panel meet. Insert the
Cam Locks (4) and turn them
clockwise to tighten and put on
the Cap (5) as shown in Figure 4.
CONSOLE
Assembly Instructions

8
Step 1:
Attach the Right Front Panel
(S) to the drawer assembly
by inserting Wood Dowels (1)
Into their corresponding
holes until the panel meet.
Insert the Cam Locks (4)
and turn them clockwise to
tighten and put on the Cap
(5) as shown in Figure 5.
Step 2:
Insert t he left and right
drawers into the assembly
as shown in Figure 5.
Figure 5
CONSOLE
Assembly Instructions

9
Parts Replacement Form
Customer Information
Name Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/si e/style number:
Style No Parts Letter Parts Description Quantity Needed
Please contact the retailer that you purchased from for returns.
Please immediately examine this product carefully. Any request for missing parts or damage replacement
must be received within 90 days of your receipt of the product. Replacement, if available, will be
honored within this time frame. Parts will not be available for items arriving fully assembled. We do
not recommend modifying product(s) and we are not responsible for any damages due to product
modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under
no obligation to provide parts or replacement merchandise.