INPRO Solarity Service manual

Installation Instructions
SolarityTM Motorized Shades with 2-1/2" & 3-1/8" Roller Tube
Installation Questions?
Contact our Installation Hotline 866.EZINPRO
For Sales & Customer Service call 800.222.5556
Instructions for motorized shades that include one of the following
motors; STD-AC, STD-ACR, STD-ILT-AC, IQM-AC, IQM-ACR, IQM-
ILT-AC, or STD-DC. Motorized Shades come fully assembled and
ready for installation. Mounting screws are not provided. The type
and size of screw required will vary depending upon the mounting
surface.
STANDARD BRACKET INSTALLATION
1. Determine and mark proper bracket locations
(Outside bracket width is shade order width).
Brackets are universal and can be installed as
wall mount or ceiling mount.
2. Mount motor and idler brackets at the appropriate bracket to
bracket dimension (Use #10 or larger truss head, pan head or hex
head screw. If head of screw is too small for screw slot in bracket,
add a washer). It is important that the brackets are level for
proper operation of the shade.
3. Insert the spring loaded idler end of the tube into bearing on idler
bracket making sure to fully engage spring and push in. Maneuver
motor into motor mount ensuring the limit switches are accessible
and the motor wire does not interfere with the shade operation.
Radio motors have programmable limits. (Secure motor with
C-shaped motor retainer clip).
4. Set the limits on the motor (see attached instructions).
OPTIONAL ALUMINUM FASCIA INSTALLATION
Follow steps 1-4 from above using 4” square mounting brackets
instead of standard mounting brackets. Shades may be installed
with fascia, fascia plus top/back cover, or top/back cover as
reverse roll fascia installation. If top/back cover is used for ceiling
mount, remove orange tape from top/back cover and stick on
brackets. Install brackets and top/back cover at the same time.
For wall mount reverse roll applications, top/back cover is used as
reverse roll fascia and requires a screw through front of reverse
roll fascia. Pre-drill 1/16” hole through fascia into flange on steel
bracket. Attach with #8 x 3/8” pan head screw provided.
5. Snap on fascia. Hook the lip of the fascia over the end brackets
and swing the fascia down until the bottom of fascia snaps
securely into place.
Idler Coupler Motor
Standard
Brackets
Fascia
Brackets
Motor Mount
Motor Retainer Clip
4” Fascia
IPC.1524/Rev.1

Installation Questions?
Contact our Installation Hotline 866.EZINPRO
For Sales & Customer Service call 800.222.5556
OPTIONAL SIDE TRACK INSTALLATION
Follow shade installation previous steps 1-5. (previous page)
6. Install side tracks. Line up outside track width even with outside
bracket to bracket width. Use level to make sure tracks are plumb.
7. For surface mount installations, screw through pre-drilled
side track. Snap plastic buttons over holes when complete.
For inside mount installations, pre-drill side rail (use 3/16” drill bit)
at desired locations before screwing to window jamb.
SPECIAL COUPLER INSTRUCTIONS
Follow shade installation previous steps 1-5. (previous page)
6. Install motor side shade bracket first. Place motor into motor
bracket (note limit switch accessibility). Slide coupler bracket on
to coupler insert (bracket is labeled on which side faces motor).
Line up coupler bracket at order dimension for first panel. Install
coupler bracket and the first shade panel together.
7. Repeat process for additional coupler brackets. Make sure that
white locating marks on black coupler inserts line up when
installing each additional shade panel. Align white locating marks
on couplers for shade panels to line up.
8. To mount the last shade panel (Shade with Spring Idler), place
spring end into ball on idler bracket, depress spring completely,
line up white dots and male and female coupler and insert into
brackets.
9. Secure motor with C-shaped motor ring.
MOTORIZED FASCIA SHADES WITH COUPLERS
Follow shade installation previous steps 1-5. (previous page)
Install 4” square fascia brackets (using #10 screws) instead of
standard motor brackets. Make sure coupler brackets are
mounted with label toward motor side.
6. After shades are completely installed and adjusted, hook the top
edge of fascia onto front of brackets and swing fascia onto
brackets until it snaps into tang on bottom of bracket.
TROUBLE SHOOTING
1. To adjust shades for telescoping (excessive horizontal movement
of fabric while shade rolls up on the tube), roll shade all the way
down so tube is exposed (this will require adjustment of the down
limit on motor).
2. Place a 4” piece of tape (2”-4” in from the end of shade) on the
side of the tube opposite of the direction the fabric is moving
toward.
Coupler Coupler
Insert insert
Line up white
dots on black
coupler
inserts to
make sure
fabric panels
line up.
Face toward Coupler Face toward
Idler bracket bracket Motor bracket
Installation Instructions
SolarityTM Motorized Shades with 2-1/2" & 3-1/8" Roller Tube

Installation Questions?
Contact our Installation Hotline 866.EZINPRO
For Sales & Customer Service call 800.222.5556
3. Run the shade up. If shade still telescopes, repeat the process.
The correct amount of tape can only be determined by trial and
error.
4. Re-set the down limit after shade adjustments are made.
OPERATION OF MOTORIZED SHADES
1. To open shade or close via wall switch or remote control, user
should have line of sight of shades being operated. User should
make sure the shades do not come into contact with any
obstruction.
2. If any shade binds up or hits an obstruction, the shade operation
should be switched off immediately.
3. Motors should not require any lubrication.
4. If motor ceases to work, electrician is required to ensure that
problem does not exist with wiring. If motor overheats, thermal
overload will activate shutting off motor until it cools down. Motor
will return to normal operation.
IMPORTANT NOTE FOR ELECTRICIAN
1. An UL Listed appropriately sized cable clamp or cable gland must
be used that is suitable for the use with the diameter of the cable.
The outside diameter of the motor cable is .340 Nominal (8.64mm)
This will make sure the connection between the motor cable and
the junction box is stable and avoid strain on the conductors.
2. Any switch, connector, and/or junction box that will be used should
be UL Listed.
3. For motorized shades provided with the NEMA 5-15P plug cap,
the need for a ground-type receptacle for connection of the supply
and the need for proper grounding is crucial. “To reduce the risk
of electrical shock, this equipment has a grounding type plug that
has a third (grounding) pin. This plug will only fit into a grounding
type outlet. If the plug does not fit into the outlet, contact a
qualified electrician to install the proper outlet. Do not change the
plug in any way.”
4. Any electrical wiring that is designed to be permanent shall be
employed as required by local codes.
+DV been granted a UL Listing for
complete motorized shade systems
(Model #s STD-AC, STD-ACR,
STD-AC-ILT, IQM-AC, IQM-ACR, and
IQM-AC-ILT).
Installation Instructions
SolarityTM Motorized Shades with 2-1/2" & 3-1/8" Roller Tube