Insignia NS-RMT3D18 User manual

USER GUIDE
3-Device
Universal
Remote
NS-RMT3D18
Final flat size: 1.65 × 8.26 in. (42 × 210 mm)
Before using your new product, please read
these instructions to prevent any damage.
V2
FINAL
FOR PRINT

PACKAGE CONTENTS
• 3-Device Universal Remote
• Quick Setup Guide
FEATURES
• Works with aTV and a cable,
satellite, or streaming box, plus
a Blu-ray or DVD player and a
soundbar or other audio-only
device
• Programming by popular brand
names for quick and easy setup
• Extensive code library for less
common brands and devices
• Premium design, materials, and
construction for rugged use
INSTALLING BATTERIES
• Insert two AAA batteries (not
included) into the remote. Make
sure that the + and – symbols
match the + and – symbols in the
battery compartment.
Note: To set up your remote, follow the
setup steps below, in order, and STOP
as soon as your remote works correctly.
PROGRAMMING YOUR
REMOTE
There are three ways to set up your
remote:
• Use“Setup method A: Popular
brands”for pre-set popular brands.
• Use“Setup method B: Direct code
entry”if your device’s direct code is
in the code list starting on page 12.
• Use“Setup method C: Code search”
to perform a code search for your
device.
Note: This remote comes pre-set for
InsigniaTVs and DVDs and AppleTV
cable/satellite/streaming set-top boxes.
Setup method A: Popular brands
1Turn on your target device.
2Press and hold SETUP until your
remote’s LED blinks twice.
3Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD to select the mode you want
to set up. The LED stays lit.

4Press either 0(for cable/satellite/
streaming), 1(forTVs), or 2(for
Blu-ray/DVD) to select the device
type you want to set up.
5Find your device type and brand
in the table below, then press and
hold its number until your device
turns o. Setup for that device is
complete.
Note: If your brand does not appear in
the table below, use“Setup method B:
Direct code entry”or“Setup method C:
Code search.”
#TVCABLE / SATELLITE
/ STREAMING
BLU-RAY/
DVD
1Insignia AT&T Insignia
2LG Bell LG
3Panasonic Comcast, Xnity Panasonic
4Philips,
Magnavox
Cox Communications Philips,
Magnavox
5Samsung DIRECTV Pioneer
6Sharp DISH Network Samsung
7Sony Frontier
Communications,
Verizon
Sharp
8TCL Rogers Sony
9Toshiba Shaw Toshiba
0VIZIO Spectrum Yamaha
Setup method B: Direct code
entry
1Turn on your target device.
2Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD to select the mode you want
to set up.
3Press and hold SETUP until your
remote’s LED blinks twice.
4Enter the rst 5-digit code for your
brand from the code list (seeTV
CODE LIST on page 12).
5Press the (power) button to test
your device. Release the key when
your device turns o. Setup for that
device is complete.
6If the device does not turn o,
repeat steps 2-5 using the next
code for your brand or use“Setup
method C: Code search”.

Setup method C: Code search
1Turn on your target device.
2Press and hold SETUP until your
remote’s LED blinks twice.
3Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD to select the mode you want
to set up. The LED stays lit.
4Press either 0(for cable/satellite/
streaming), 1(forTVs), or 2(for
Blu-ray/DVD) to select the device
type you want to set up.
5While pointing the remote toward
your target device, press and hold
OK until your device turns o.
Release the key when your device
turns o. Setup for that device is
complete.
LEARNING FUNCTIONS
FROM ANOTHER REMOTE
You can learn any function from your
original (working) remote control.
Creating a learned function
1Make sure that your remote is
programmed to the device you
want to control. See“Programming
your remote.”
2Place your original and new
remotes on a table with their IR
sensors 1-2" apart.
3With your new remote, press and
hold SETUP until the LED blinks
twice.
4With your new remote, press 9, 7, 5.
5With your new remote, press
TELEVISION or CABLE /
SATELLITE / STREAMING, or
BLURAY/DVD for the device
you want to learn a function from.
6With your new remote, press the
button you want to add a function to.
The LED blinks continuously.
Note: Functions cannot be assigned to
the setup key or the three device keys.

7With your original remote, press the
button with the function you want
to teach.The LED blinks twice.
Note: If the LED displays a long blink,
the function wasn’t learned. Start from
step 5 to try again.
8Repeat steps 5-7 for each button
you want to learn.
9Afteryou haveadded allthe functions,
press and hold SETUP on your new
remote until its LED blinks twice.
Deleting a learned function
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD for the device you want to
delete a function from.
3Press 9, 7, 6.
4Press the button with the learned
function twice. The LED blinks
twice and the button resets to its
original function.
USING YOUR REMOTE
1Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD for the device you want to
control.
2Press the buttons applicable to
that type of device.
Watch TV mode
Note: To control a soundbar or other
audio device with your remote, see
Adding an audio device.
While watchingTV in CABLE /
SATELLITE / STREAMING mode,
you can:
• Use your remote’s volume and
input buttons to control theTV. The
rest of the buttons will control the
device you’ve added to CABLE /
SATELLITE / STREAMING mode.
• Press (power) once to turn your
set-top box on or o.
OR
• Press and hold (power) for two
seconds to turn both your set-top
box and yourTV on or o.

To turn o watch TV mode:
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press CABLE / SATELLITE /
STREAMING twice.The LED blinks
four times.
WatchTV mode is turned o and
your remote will not control yourTV.
To turn on watch TV mode after
turning it o:
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press CABLE / SATELLITE /
STREAMING twice.The LED blinks
twice.
WatchTV mode is turned back on
and your remote will control your
TV again.
ADDING AN AUDIO DEVICE
If you listen to sound through
a connected audio device (for
example, a soundbar or audio/video
receiver), you can program your
remote to control it when in
CABLE / SATELLITE /
STREAMING mode:
• Use“Method A: Popular audio
devices”if your audio device is
listed as a popular brand, or
• Use“Method B: Audio device code
entry”to perform a code search for
your device.
Method A: Popular audio devices
1Turn on your audio device and play
something through its speakers.
2Press and hold SETUP until your
remote’s LED blinks twice.
3Press MUTE.
4Find your audio device’s brand and
corresponding number in the table
on the next page.
5While aiming the remote at your
audio device, press and hold your
audio device’s number (from
step 4) until the sound mutes.
Setup is complete and your remote
controls your audio device’s volume
while using a cable, satellite, or
streaming device.

# AUDIO # AUDIO
1Bose 6Philips
2Denon 7Pioneer
3LG 8Samsung
4Onkyo 9Sony
5Panasonic 0Yamaha
Method B: Audio device code
entry
1Turn on your audio device and play
something through its speakers.
2Press and hold SETUP until your
remote’s LED blinks twice.
3Press MUTE.
4Find your audio device’s brand in
the code list (see AUDIO CODE LIST
on page 57), then use your remote
to enter the rst 4-digit code for
your brand from the code list.
5Press MUTE to test your audio
device. If the sound mutes, setup
is complete and your remote
controls your audio device’s volume
while using a cable, satellite, or
streaming device.
6If the sound doesn’t mute, repeat
steps 2-5 using the next code for
your brand.
LOCKING AND UNLOCKING
VOLUME CONTROLS
By default, theVOL /
(volume up/down) and (mute)
buttons control yourTV. You can
lock this setting so the remote
always controls your cable/satellite/
streaming device, or unlock it so
each device controls its own volume.
Locking volume controls to one
device
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press 9, 9, 3.
3Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD to lock volume controls to
that device.The LED blinks twice.

Unlocking volume controls
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press 9, 9, 3, then press VOL
(volume up).
LOCKING AND UNLOCKING
CHANNEL CONTROLS
Locking channel controls to one
device
1 Press and hold SETUP until your
remote’s LED blinks twice.
2Press 9, 7, 3, then press CH +.
3Press TELEVISION or
CABLE / SATELLITE /
STREAMING, or BLURAY/
DVD to lock channel controls to
that device.The LED blinks twice.
Unlocking channel controls
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press 9, 7, 3, then press CH -.
RESETTING REMOTE TO
FACTORY DEFAULTS
1Press and hold SETUP until your
remote’s LED blinks twice.
2Press 9, 7, 7.

REMOTE OVERVIEW

# ITEM DESCRIPTION
1SETUP Programs the remote
2TELEVISION Press to control
yourTV
3Numbers Enter channel
numbers
4Delimiter
(-)
Enters a digital
sub-channel number
(for example 4.1)
5Home Opens the home
menu
6MENU Displays the main
menu
7OK Conrms a selection
8INFO Displays info on the
current program
9LAST Return to the last
channel
10 Volume up/
down
Raises or lowers the
volume
11 MUTE Mutes the sound
12 VOD Press to order
video-on-demand or
pay-per-view
13 Red, green,
yellow,
blue
Shortcut keys in some
menus
14 Playback
controls
Control devices
connected to yourTV
15 REC Starts or stops
recording
16 Power Turns devices on
and o
17 BLURAY/
DVD
Press to control a
Blu-ray and DVD
18 CABLE /
SATELLITE /
STREAMING
Press to control a
cable / satellite /
streaming device
19 ENTER Conrms a menu
selection
20 GUIDE Displays the program
guide
21 EXIT Exits the current
menu
22 INPUT Select input/source
to be displayed (for
example HDMI 1)
23 Channel up/
down
Changes the channel
24 APPS Opens a smart
device’s app menu
25 LIST Displays a list of
recorded shows