INSTEON SignaLinc RF User manual

Quick-Start Guide
SIGNAL ENHANCERS Pass-through
Outlet
Antenna
Set Button
Status LED
Two Signal Enhancers are required in each home with INSTEONTM
enabled products.
SignaLincTM RF (#2442P)
NNeeeeddHHeellpp??FFoorraassssiissttaanncceeccaallllyyoouurrffrriieennddllyy
ssuuppppoorrttppeerrssoonn@@886666--224433--88001188
Signal Enhancers repeat all INSTEON messages, thereby ensuring
a highly reliable INSTEON Network.
PART ONE: Installing Two Signal Enhancer Interfaces
SStteepp22..Point your Signal Enhancer’s antenna towards the floor or ceiling.
SStteepp33..On the ffiirrssttSignal Enhancer press and hold the SET button for 10 seconds and release.
The Signal Enhancer’s LED will bblliinnkkffaasstt((44ttiimmeessppeerrsseeccoonndd))and will continue to blink until you complete step 7. If it
does not blink, try again and don't let up too soon — 10 seconds is a pretty long time!
SStteepp11..Plug the ffiirrssttSignal Enhancer into a convenient wall outlet.
SStteepp44..Plug the sseeccoonnddSignal Enhancer into another outlet.
SStteepp55..Point your Signal Enhancer’s antenna towards floor or ceiling.
SStteepp66..Look at the sseeccoonnddSignal Enhancer’s Status LED:
• If it is bblliinnkkiinnggffaasstt, go to step 7.
• If it is bblliinnkkiinnggsslloowwllyy((oonncceeeevveerryy22sseeccoonnddss))oorrnnoottbblliinnkkiinnggaattaallll, repeat step 4 trying another outlet.
NNoottee::YYoouum
maayynneeeeddttoottrryysseevveerraalloouuttlleettss..If you are unable to locate a “fast blinking” outlet please call 866-243-8018
for assistance. If you have tried 5 outlets go back and move the first SignaLinc to another outlet.
SStteepp77..Press and release the SET button on the ffiirrssttSignal Enhancer.
The Status LED on both Signal Enhancers will stop blinking and remain steadily on.
Congratulations! You have made your home INSTEON ready.
HINTS
• Do not use an outlet controlled by
a switch.
• Don’t place near large metal
objects.
• Point the antennas on both
Signal Enhancers in the same
direction.

Quick-Start Guide
SIGNAL ENHANCERS
Troubleshooting Tips
•The Status LED on the first Signal Enhancer I installed is not blinking.
Refer to Step 3 and press and hold for a longer amount of time. Remember, 10 seconds is a pretty long time!
•I have tried several outlets and the second Signal Enhancer’s Status LED is not blinking.
Move the antenna and retry, moving closer to the first Signal Enhancer.
•The Status LED on the Signal Enhancer is not turning on at all.
Make sure you are not on a switched outlet.
The advanced User's Guide can be found at hhttttpp::////wwwwww..ssmmaarrtthhoommee..ccoomm//22444422..hhttmmll.
SSmmaarrttLLaabbssLLiimmiitteeddWWaarrrraannttyy
SmartLabs warrants to the original consumer of this product that, for a period of two years from the date of purchase, this product will be free from defects in material and workmanship and will perform
in substantial conformity to the description of the product in the owner's manual. This warranty shall not apply to defects or errors caused by misuse or neglect.
©©CCooppyyrriigghhtt22000066SSmmaarrttLLaabbss,,1166554422MMiilllliikkaannAAvvee..,,IIrrvviinnee,,CCAA9922660066--55002
277
886666--224433--88001188wwwwww..ssmmaarrttllaabbssiinncc..ccoomm
NNeeeeddHHeellpp??FFoorraassssiissttaanncceeccaallllyyoouurrffrriieennddllyy
ssuuppppoorrttppeerrssoonn@@886666--224433--88001188
rev. 071106