INTELIGAIN SG800 User manual

SG800 Signal Amplifier Installation Manual Page 1 of 1
Copyright 2002, Seamless Group, Inc., All rights reserved.
Rev A D00000413
Made in North America
Note: Before installing the SG800 Signal Amplifier, please read the entire contents of this manual.
Parts List
Item Qty Description
1 1 SG800 InteligainTM Signal Amplifier
2 1 1.5 Meter (59”) RF Cable
3 1 2 Meter (78”) DC Power Cable
4 1
Connector Adapter FME Female to TNC
Male
5 1
Connector Adapter FME Male to TNC
Male
3A
Fuse
PHONEANTENNA
1
2
3
5 4
3A
Fuse
PHONEANTENNA
1
2
3
5 4
Tools and Other Materials Required
Item Description
1 Electric drill (as required for signal amplifier mounting holes)
2 Screw driver
3 Qty 4 screws (length and type as required for signal amplifier mounting)
4 Wire cutters / strippers
5 Qty 2 wire connection insulators or insulating material (as required for DC power cable connection to 12V DC system)
WARNINGS!
Ñ An antenna of not more than 5dBd gain shall be used with the amplifier or the manufacturer’s warranty will be void. Use
of cellular amplifiers with antennae of higher gains is in violation of FCC regulations for which the offender will be fully
liable.
Ñ Ensure that the external antenna connected to the SG800 amplifier is mounted at least 0.5 meter away from any seating
position in the automobile to ensure that the FCC Maximum Possible Exposure (MPE) guidelines are satisfied. At a
distance of 0.5 meter from the externally mounted 5dBd antenna connected to the SG800, the uncontrolled MPE power
density will be 0.33mW/cm2(FCC guideline 0.55mW/ cm2).
Ñ Mounting a signal amplifier in the engine cavity or on the underside of the vehicle will void the manufacturer’s warranty.
Ñ Subjecting the amplifier to voltages greater than 30 Volts DC will damage the amplifier and void the manufacturers
warranty.
Ñ Any vehicle with an electrical system of greater than 30 Volts DC should use a step-down voltage regulator to bring the
voltage within the DC operating power range of the amplifier (10 to 30V dc).
Ñ Under no circumstances should the amplifier be powered up without a properly connected 50 ohm 800 MHz cellular
antenna or the amplifier may be damaged and the manufacturer’ warranty will be void.
It is recommended that only certified automotive installation technicians install this product in a
vehicle. Installation by any other person is at the risk of the vehicle owner and operator.
Installation
Selecting a Suitable Location To Mount The Signal Amplifier
Locate a suitable place to mount and conceal the signal amplifier. Suggested mounting locations include: under the dashboard, under a
seat, or in the trunk. For peak performance the signal amplifier should be mounted as close to the phone handset as possible. The
amplifier’s location should be easily accessible and mounted away from moving parts, as well as excessive heat and moisture.

SG800 Signal Amplifier Installation Manual Page 2 of 2
Copyright 2002, Seamless Group, Inc., All rights reserved.
Rev A D00000413
Made in North America
Installation Cautions
Ñ Use caution to avoid drilling through or near fuel lines or fuel tanks; brake lines; or electrical wiring.
Ñ Do not mount the signal amplifier or its associated wiring in a location that may interfere with the safe operation of the
vehicle.
Installation Of The Signal Amplifier
Signal Amplifier
1.5 M
Cable Color/ Black
Black
(12 V DC)
Antenna *1
Antenna
Cable *1
*1Optional items must be purchased separately .
Phone/Cradle or RF
output device *1
1
2
3
Signal Amplifier
1.5 M
Cable Color/ Black
Black
(12 V DC)
Antenna *1
Antenna
Cable *1
*1Optional items must be purchased separately .
Phone/Cradle or RF
output device *1
1
2
3
Typical Installation For Under The Seat Mounting
1. For safety, disconnect the vehicle’s negative “-“ battery terminal to remove power from the vehicle.
2. Drill holes and mount the signal amplifier (ITEM 1) in the selected location.
3. Connect the coloured striped black wire of the supplied 2 Meter (78”) power cable (ITEM 3) for the signal amplifier to a positive
connection on the vehicle’s electrical system. Choose a 10 to 30 Volt DC circuit that is: fuse protected; and ignition switched.
(Often referred to as the “Accessory output”)
4. Attach the solid black wire of the supplied 2 Meter (78”) power cable (ITEM 3) to a vehicle electrical ground point.
5. Attach one end of the antenna cable*1to the antenna. The other end is connected to the cellular phone handset via a cradle or an
RF output cable*1 to the signal amplifier’s ANTENNA output connector. Use the supplied FME to TNC adapters (ITEM 4 or 5) if
necessary.
6. Connect the amplifier’s PHONE input connector to the cellular phone handset via a cradle or an RF output cable using the
provided 1.5 Meter (59”) RF cable (ITEM 2) and adapter (ITEM 4 or 5) if necessary.
7. Reconnect the vehicle’s negative “-“ Battery terminal.
Limited Warranty
Seamless Group Inc. warrants that this product is free from any defects in material or workmanship for a period of one year. If a defect
in material or workmanship is found, Seamless Group Inc. agrees to repair or replace the product at its own discretion, free of charge to
the original purchaser. Please return the product along with proof of purchase to the original authorized dealer. This warranty is null and
void if the product has been modified, abused, tampered with, subjected to abnormal conditions, or transferred to someone other than
the original purchaser.
All brands and trademarks are the property of their respective owners. Designed and manufactured in North America