Intelligent Weighing Technology MII-600 User manual

MII SERIES
DIGITAL WEIGHING SCALE
OPERATION MANUAL
PLEASE READ THIS MANUAL VERY CAREFULLY
BEFORE ATTEMPTING TO OPERATE THE SCALE
February 2006 Rev 2
Specifications subject to change without prior notice.

CONTENTS
1. INSTALLATION
2. SPECIFICATIONS
3. KEYBOARD LAYOUT AND DESCRIPTION
4. INITIAL SETUP
5. INSTRUCTIONS FOR USE
6. TROUBLE SHOOTING
7. DAILY CARE AND MAINTENANCE

1. INSTALLATION
1.1 Check to make sure that the following items are
included:
This operation manual
Scale x 1
Stainless steel platter cover x 1
Power adapter x 1
Contact your dealer if any items are missing.
1.2 Insert the legs of the plastic platter carefully into the
holes on top of the scale, then place the stainless steel
platter on top.
1.3 Power the Scale
a. Insert one 9V battery into the battery pack
underneath the scale, or
b. Connect the power adapter. Before plugging the
power adapter into electricity outlet, check to make sure
that the input voltage of the power adapter matches the
output voltage of the outlet. If not, do not plug in the
adapter. Contact your dealer immediately.
CAUTION:
When the power adapter is being used, take the battery
out from the battery pack. Failure to do so may cause
battery leak / explosion or damage to the scale. Do not
use any rechargeable battery. The scale does not
recharge any battery.
1.4 Retain the packing materials for future transportation
use.

2. SPECIFICATIONS
Model No. Capacity Division
MII-600 600 g / 21 oz 0.1 g / 0.005 oz
MII-1200 1200 g / 2 lb : 8 oz 0.2 g / 0.01 oz
MII-3000 3000 g / 6 lb 0.5 g / 0.02 oz
MII-6000 6000 g / 13 lb 1 g / 0.05 oz
Power source 1 x 9V battery or power adapter
Max. zero range 100% of rated capacity (subtractive)
Weight Units g, lb:oz
Operation
Environment 0° to 40° C (32° to 104° F) Non-condensed. R.H. 85%

3. KEYBOARD LAYOUT AND DESCRIPTION
ON/ZERO KEY
Press this key to turn scale on or to return the scale to
zero.
TARE KEY
Press this key to tare off the weight of a container or set
a negative weight displayed to zero when unloaded.
MODE KEY
Press this key to switch between metric and
avoirdupois weight units.
OFF KEY
Press this key to turn off the unit.
AVOIRDUPOIS UNITS INDICATOR
The lb:oz indicator will appear when the avoirdupois
weight unit is being employed.
ZERO INDICATOR
This 0indicator will appear when the scale is at true
zero.
LO-BAT INDICATOR
This indicator will appear when the battery voltage is
too low. Replace battery or immediately apply the
power adapter provided.
METRIC INDICATOR
This gindicator will appear when the metric weight is
displayed.

4. INITIAL SETUP
4.1 Internal Settings
The scale is equipped with Auto Power Off Function
and metric and avoirdupois weight units.
a. Press and hold TARE, then press ON/ZERO.
b. FUN 1 is displayed.
c. Press TARE to select the desired function.
FUN 4
Press MODE to move between:
4off the scale will turn off in 4 minutes.
10off the scale will turn off in 10 minutes
20off etc.
0off the scale will not turn off
When you have selected the required setting, press
ON/ZERO to return to weighing.
Note: Under the Auto Power Off function mode, the scale will
turn off automatically when left idle.

5. INSTRUCTIONS FOR USE
5.1 Before using, make sure that:
a. The plastic platter is placed correctly on top of the
load receptor and the stainless steel platter cover is
placed on top.
b. The scale is placed on a level and strong surface.
c. The scale is turned on.
d. The ZERO Indicator is on. If not, press ON/ZERO to
set the display to zero.
5.2 Weighing
a. Always place an object onto the platter gently.
Excessive force applied to the platter may cause
damage to the sensor inside the scale.
b. The weight of the object will be displayed
automatically.
c. It is a good practice to remove all loads from the
platter after weighing. It will prolong the life of the
scale.
5.3 Selecting the Weighing Unit
Press MODE to shift between g and lb/oz. Refer to
4.1.1 for internal setting procedures.
The weight unit used before power off will be employed
when the scale is turned on again.
Refer to 5.2 for weighing procedures. Weight displayed
is the net weight of the load. Refer to
SPECIFICATIONS for maximum tare range.

5.5 Tare off the weight of a container.
When a container is used, follow the below steps to
tare off its weight and get a net weight result.
a. Remove all loads from the platter.
b. The ZERO INDICATOR will appear.
c. Place the container on the platter.
d. Press TARE.
After ZERO is pressed, the scale will display TARE and
then a zero weight value will be displayed. The ZERO
INDICATOR will not appear even though a zero weight
is displayed. The net weight is displayed.
5.6 Clear the Tare Function
a. Remove all loads from the platter.
b. The scale will display a negative value, which is the
weight of the container. The ZERO INDICATOR will
appear.
c. Press ZERO.
d. After ZERO is pressed, a zero weight will be
displayed while theZERO INDICATOR remains.
5.7 LO-BAT Indicator
When the LO-BAT INDICATOR appears, it means that
the battery is faded out. Replace the battery with a new
one or apply the power adapter immediately.
CATION: When the power adapter is being used, take the
battery out from the battery pack. Failure to do so may
cause battery leak / explosion or damage to the scale.

6. TROUBLE SHOOTING
Symptom: Scale cannot be turned on
Check: Is the scale powered or battery low?
Action: Refer to 4.1 Select AUTO POWER OFF
function status and weight unit to disable the
AUTO POWER OFF function.
Check: Is the power adapter inserted properly into both
the electricity outlet and the DC inlet of the scale.
Action: Secure both ends of the power adapter and try
again.
Symptom: Scale turned off automatically.
Check: Is the AUTO POWER OFF function employed?
Action: Refer to 4.1 Select AUTO POWER OFF
function status and weight unit to disable the
AUTO POWER OFF function.
Check: Is the LO-BAT INDICATOR on?
Action: Replace the battery with a new one, or apply the
power adapter immediately.
CATION: When the power adapter is being used, take the
battery out from the battery pack. Failure to do so may
cause battery leak / explosion or damage to the scale.
Symptom: Weighing result is not accurate.
Check: Is the scale placed in a level condition?
Action: Relocate the scale to obtain a level condition.
Check: Is the scale affected by air flow, vibration of RFI?
Action: Place the scale away from all disturbances.
Check: Is the scale calibrated correctly?
Action: Contact your dealer.
Check: Is the correct weight unit employed?
Action: Refer to 4.1 and 5.3 for weight unit setting and
usage.

7. DAILY CARE AND MAINTENANCE
7.1 Do not splash water on the scale. Clean the scale with
a soft, damp cloth. If necessary, apply a mild
detergent.
7.2 Do not use any harsh, abrasive material, acetone,
volatile solvent, thinner or alcohol for cleaning.
7.3 Verify the accuracy of the scale periodically. Re-
calibrate the scale if necessary.
NOTE: In some countries, calibration is restricted to be done
by an authorized/qualified agent only. Contact your dealer for
more information.
7.4 Store the scale in a dry and clean place.
7.5 Before storage for a long period of time, remove all
batteries from the battery pack.
7.6 Do not open the scale. There are no serviceable parts
inside. Contact your dealer for after service.