Intellinet 522328 User manual

GiGabit
PCi
Network
Card
user maNual
MODEL 522328
INT-522328-UM-0108-01

Thank you for purchasing the INTELLINET NETWORK SOLUTIONS
™
Gigabit PCI Network Card, Model 522328.
A high-performance network adapter designed to t into the PCI slot of
your desktop computer, this card allows you to upgrade your computer to
support Gigabit network speeds without changing your copper network
cabling scheme to ber optic.
And with the easy-to-follow instructions in this manual, you’ll soon be able
to enjoy the benets of these additional features:
• Supports Gigabit speeds over existing network cable
• Does not require ber optic cabling to run Gigabit speeds
• Supports 32-bit PCI V2.2, 2.1 and 2.0, 33/66 MHz
• Full duplex speeds (20 Mbps, 200 Mbps, 2000 Mbps)
• Auto-negotiation with next-page capability
• Supports up to 128 kB ash boot ROM (option)
• Full duplex ow control (IEEE 802.3x)
• VLAN Tagging (IEEE 802.1Q)
• 8 kBytes transmit buffer and 64 kBytes Receive buffer
• Realtek 8169 chipset
• Pair swap/polarity/skew correction
• Crossover detection and auto-correction
• Microsoft NDIS5 Checksum Ofoad (IP, TCP, UDP) and large-send
ofoad support
• Wake-On LAN and remote wake-up support
• Lifetime Warranty
System Requirements
Prior to card installation, make sure the following are available:
• 32- or 64-bit PCI master mode expansion slot compliant with PCI bus
specications
• CD-ROM drive
• Corresponding cables (see NOTE below):
3
Port Type Media Maximum Distance
10Base-T Cat. 3, 4 or 5 UTP 100 meters
100Base-TX Cat. 5 or 5e UTP 100 meters
1000Base-T Cat. 5, 5e or 6 UTP 100 meters

NOTE: 1000Base-T signaling requires four twisted pairs of Category 5/6
balanced cabling, as specied in ISO/IEC 11801:1995 and ANSI/EIA/
TIA-568-A (1995) and tested for additional performance using testing
procedures dened in TIA/EIA TSB95.
FCC Statement
This device compiles with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including interference
that may cause undesired operation
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the
interference at his own expense.
CE Mark Warning
In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
4

hardware iNstallatioN
1. Turn off the computer and unplug the power cord.
2. Remove the computer’s cover (refer to its manual if necessary).
3. Insert the contact edge of the Gigabit PCI Network Card into the
connector of any available PCI bus master expansion slot. Press the
card rmly into the slot, making sure the card’s contacts are fully seated.
4. Install the bracket screw that secures the card to the computer chassis.
5. Replace the computer’s cover.
6. Connect the UTP cable to the RJ-45 network connector.
software iNstallatioN
If the BIOS section of your computer’s boot program is Plug and Play–
compliant, BIOS will automatically congure any newly installed adapter
when the computer is turned on. NOTE: Due to occasional problems with
some Plug and Play BIOS programs, a newly installed adapter may be
assigned an interrupt number that is already used by another device. In
such case, the conict will cause faulty behavior in both devices, which
makes it necessary to run the CMOS Setup utility and manually assign
a non-conicting interrupt number.
WINDOWS 98SE
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. An Add New Hardware Wizard screen will display “PCI Ethernet
Controller.” Click “Next.”
3. On the second Add New Hardware Wizard screen, select “Search for
the best driver for your device” and click “Next.”
4. Insert the enclosed driver CD.
5. Enter the driver pathname “E:\” (E representing your CD-ROM drive).
Click “Next.”
6. Select your installed adapter and click “Next.”
7. To complete the process, follow any remaining on-screen instructions.
8. Restart the computer.
5

6
WINDOWS Me
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. An Add New Hardware Wizard screen will display “PCI Ethernet
Controller.” Insert the enclosed driver CD.
3. Select “Install the software automatically” and click “Next.”
4. When the device name displays on the Add New Hardware Wizard
screen, click “Finish.”
5. Restart the computer.
WINDOWS NT 4.0
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. Click the My Computers icon; double-click the Control Panel icon.
3. In the Control Panel icon group, double-click the Network icon.
4. In the Network Settings dialog box, select the Adapter tab, then click
“Add” to display a list of network adapters.
5. Click “Have Disk” to select the network adapter.
6. Insert the enclosed driver CD. Enter the pathname “E:\Winnt4” (E
representing your CD-ROM drive), then click “OK.”
7. With the Gigabit PCI Network Card (“Gigabit Ethernet Network Adapter”)
string displayed in the Select OEM Option panel, click “OK.”
8. Select the connection type; click “OK.”
9. To complete the process, follow any remaining on-screen instructions.
10. Restart the computer.
WINDOWS 2000
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. A Found New Hardware Wizard screen will display “Welcome to the
Found New Hardware Wizard.” Click “Next.”
3. A second Found New Hardware Wizard screen will display “Ethernet
Controller.” Select “Search for a suitable driver for my device” and
click “Next.”
4. The next Found New Hardware Wizard screen will display “Optional

7
search locations:” Select “Specify a location” and then click “Next.”
5. Insert the enclosed driver CD.
6. On the next Found New Hardware Wizard screen, enter the driver
pathname “E:\” (E representing your CD-ROM drive), then click “OK.”
7. The next Found New Hardware Wizard screen will display “The wizard
found a driver for the following device Ethernet Controller.” Click “Next.”
8. The nal Found New Hardware Wizard screen will display “Windows
has nished installing the software for this device.” Click “Finish” to
complete the installation.
WINDOWS XP
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. An Add New Hardware Wizard screen will display “Ethernet Controller.”
Insert the enclosed driver CD.
3. Select “Install the software automatically” and click “Next.”
4. A Hardware Installation screen will display the device name (“Gigabit
Ethernet Network Adapter”). Click “Continue Anyway.”
5. The next Found New Hardware Wizard screen will display “The wizard
has nished installing the software for Gigabit Ethernet Network Adapter/
Fiber Gigabit Ethernet Network Adapter.” Click “Finish” to complete
the installation.
WINDOWS VISTA
1. With the Gigabit PCI Network Card inserted into the PCI slot, turn the
computer on.
2. Windows will automatically nd the card and assign a default network
driver.
3. On the Start menu bar, go to Control Panel ‡System ‡Device
Manager ‡Network Adapters.
4. Double-click on this card and select “Update driver.”
5. Click “Browse” and select “Computer,” then “your CD-ROM drive,” then
“WVISTA32/64.” Click “OK” to start the installation.
6. When installation is complete, close the window.

LINUX KERNEL 2.2.x
1. Compiling rtl8169.c
“gcc -DMODULE -Wall -Wstrict-prototypes -O6 -c rtl8169.c”
2. Move the object code rtl8169.o to the directory
“/lib/modules/2.2.14-5.0/net”
“cp rtl8169.o /lib/modules/2.2.14-5.0/net”
3. Insert module to kernel
“insmod rtl8169”
4. Check the driver status
“dmesg”
5. The media can be forced to one of ve modes (see below).
The link speed and duplex mode can be forced in ve modes.
Command: “insmod rtl8169 media = SET_MEDIA”
Example: “insmod rtl8169 media=0x04” will force the link mode to be
100 Mpbs half duplex.
SET_MEDIA can be:
_10_Half = 0x01
_10_Full = 0x02
_100_Half = 0x04
_100_Full = 0x08
_1000_Full = 0x10
LINUX KERNEL 2.4.x
1. 1. Compiling r8169.c using Makele
“make”
NOTE: Remember to assign “NEW_INCLUDE_PATH” in Makele
according to Linux kernel.
2. Move r8169.o to the directory
“/lib/modules/<kernel>/kernel/drivers/net”
“cp r8169.o /lib/modules/<kernel>/kernel/drivers/net” where <kernel>
represents the kernel version, say 2.4.18-3 in Red Hat 7.3
3. Insert module by
“insmod r8169”
4. Check driver status
“dmesg”
8

5. The media can be forced to one of the ve modes (see below).
Cmd: “insmod r8169 media = SET_MEDIA”
Example: “insmod rtl8169 media=0x04” will force PHY to operate in
100 Mpbs half duplex.
SET_MEDIA can be:
_10_Half = 0x01
_10_Full = 0x02
_100_Half = 0x04
_100_Full = 0x08
_1000_Full = 0x10
NOVELL NETWARE SYSTEM (4.X)
1. Update Netware Server to 4.2. NOTE: If you don’t update to 4.2, use
the update le “MSM.NLM, ETHERTSM.NLM” on the CD.
2. Run NetWare Server System.
3. When the server prompt appears, load the NetWare Server Installation
Utility (“LOAD INSTALL”).
4. In the Installation Options menu, select “Driver options.”
5. In the Driver Options menu, select “Congure network drivers.”
6. In the Additional Driver Actions menu, select “Select a driver.”
7. Press <Ins> to install an unlisted driver, then press <F3> to specify a
different path.
8. Insert the driver CD and specify the path “E:\NWServer\” (E representing
your CD-ROM drive).
9. In the Select a driver to install: menu, select “Gigabit Ethernet Network
Adapter” (Gigabit PCI Network Card).
10. If necessary, select the Select/Modify driver parameters and protocols”
menu.
11. Follow any remaining instructions to complete the driver installation.
NOVELL NETWARE SYSTEM (5.X/6.X)
1. Run NetWare Server System.
2. When the server prompt appears, load the NetWare Server Installation
Utility (“LOAD NWCONFIG”).
9

3. In the Installation Options menu, select “Driver options.”
4. In the Driver Options menu, select “Congure network drivers.”
5. In the Additional Driver Actions menu, select “Select a driver.”
6. Press <Ins> to install an unlisted driver, then press <F3> to specify a
different path.
7. Insert the driver CD and specify the path “E:\NWServer\” (E representing
your CD-ROM drive).
8. In the Select a driver to install: menu, select “Gigabit Ethernet Network
Adapter” (Gigabit PCI Network Card).
9. If necessary, select the Select/Modify driver parameters and protocols”
menu.
10. Follow any remaining instructions to complete the driver installation.
sPeCifiCatioNs
10
NETWORK
• IEEE 802.3 (10Base-T Ethernet)
• IEEE 802.3u (100Base-TX Fast
Ethernet)
• IEEE 802.3ab (1000Base-T Gigabit
Ethernet)
• RJ-45 connector
• MDI/MDI-X
• Ethernet 10 Mbps (half duplex)
• Ethernet 20 Mbps (full duplex)
• Fast Ethernet 100 Mbps (half duplex)
• Fast Ethernet 200 Mbps (full duplex)
• Gigabit 1000 Mbps (half duplex)
• Gigabit 2000 Mbps (full duplex)
HARDWARE
• FCC Compliance, CE Mark
• Compliant with 32-bit PCI V2.2
• Bus speed: 66 or 33 MHz
• 10 Mbps Link/Act LED: green/blinking
green
• 100 Mbps Link/Act LED: green/
blinking green
• 1000 Mbps Link/Act LED: green/
blinking green
ENVIRONMENTAL
• Dimensions: 13 x 15.7 x 1.5 WxDxH) cm
(5.1 x 6.2 x 0.6 in.)
• Weight: 56.7 g (2 oz.)
• Operating temperature: 0 – 50°C
(32 – 122°F)
• Storage temperature: 20 – 70°C
(4 – 158°F)
• Operating humidity: 10 – 90%,
non-condensing
• Storage humidity: 5 – 95%,
non-condensing
SUPPORTED OS
• Windows 2000, XP, Vista
• Mac
• Linux

INTELLINET NETWORK SOLUTIONS™offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intellinet-network.com.
Copyright © INTELLINET NETWORK SOLUTIONS
All products mentioned are trademarks or registered trademarks of their respective owners.