Intellinet 524681 User manual

Wireless
300N 3G
router
quick
iNstall
Guide
Model
524 6 81
INT-524681-QIG-0809-03

2
iNtroductioN
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS
™
Wireless 300N 3G Router, Model 524681.
This quick install guide presents the basic steps required for setting up
and operating this device. For detailed instructions and specications,
refer to the user manual on the CD enclosed with this product at
www.intellinet-network.com.
System Requirements
• For a complete list of compatible 3G USB modems, visit
www.intellinet-network.com
Package Contents
• Wireless 300N 3G Router
• Power adapter
• Ethernet Cat5 RJ45 cable: 1.0 m (3 ft.)
• USB extension cable: 1.0 m (3 ft.)
• User manual on CD; quick install guide
NOTE: Some screen images have been modied to t the format of this
guide. Screen images on all compatible operating systems are similar.

3
3
coNNectioNs
1. With the router properly positioned on a at, stable surface, connect
your 3G / 3.5G USB modem by inserting it in the USB port on the
right side of the router’s front panel (below).
2. Connect all your computers, network devices (such as game consoles
or switches/hubs) to the LAN port(s) of the router (back panel, below).
3. Plug the power adapter into an AC electrical outlet, then connect it to
the 12VDC jack on the router. The Power LED on the front panel
should be on, and the other LEDs should light if the devices they
correspond to are also powered on and properly connected to the
router. (If they don’t, check the connections.)
Wireless 300N 3G Router
4 3 2 1 WAN ON/OFF Reset/WPS
12VDC

4 4
NetWork setup
The following procedure is for conguring the Wireless 300N 3G Router
using your Web browser. NOTE: For the initial conguration, a computer
with a wired Ethernet connection is required.
1. Set your computer to obtain an IP address from the wireless router:
Go to Start (in the lower-left corner of your desktop), then go to
Control Panel. Double-click Network Connections, then double-click
Local Area Connection. When the Local Area Connection Status
screen displays, click “Properties.”

2. When the Local Area Connection Properties screen displays, select
“Internet Protocol (TCP/IP),” then click “Properties.”
5

3. When the Internet Protocol (TCP/IP) screen displays, select “Obtain
an IP address automatically” and “Obtain DNS server address
automatically,” then click “OK.” The IP address setup is now complete.
6

4. Go to Start again, then
Run. Enter “cmd,” then
click “OK.”
5. Enter “ipcong,” then press <Enter>. Check the “IP Address” and
“Default Gateway” settings. (In the example below, the IP address of
router — the default gateway — is 192.168.2.1.)
7
C:\Documents and Settings\home user>ipconfig
Windows IP Configuration
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
IP Address . . . . . . . . . . . . . . . . . . : 192.168.2.3
Subnet Mask . . . . . . . . . . . . . . . . .: 255.255.255.0
Default Gateway . . . . . . . . . . . . . : 192.168.2.1
C:\Documents and Settings\home user>_

6. Activate your Web browser and
enter the IP address of the
router in the browser’s address
bar. When the subsequent
Login window displays (right),
ll in the “User name” and
“Password” elds (username
default is “admin”; password
default is “1234”), then click
“OK” to present the Web
management interface of the
router.
7. When the Home screen of the Web management interface displays,
click the Quick Setup button on the left.
8

8. When the subsequent Time Zone screen displays, select your local
time zone from the drop-down menu and click “Next.”
9. When the subsequent Broadband Type screen displays, select “3/3.5G”
for the Internet connection, then click “Next.”
10. When the next screen displays the settings options (below), enter the
Internet connection values if/as required by your 3G / 3.5G service
provider. Click “OK.”
9

11. With the Basic Settings screen displayed, make the selections/entries
you prefer, then click “Next.”
12. To protect your wireless network, it’s recommended that the security
be enabled. Select a security type from the drop-down menu, enter the
encryption key, then click “OK.”
10