Intercoax ETP-2601T User manual

Package
ETP-2601T (Transmitter)
ETP-2601R (Receiver)
Terminal
Connector
Bracket Quick Start
Guide
Hardware Overview
Right
Left
브라켓 홀DC 전원 어댑터
브라켓 홀
RJ45
PoE ON/OFF 스위치
(ETP-2601T 전용)
Join 버튼
상태 표시등
PoE-ON (ETP-2601T)
PD-AUX (ETP-2601R)
Bracket Hole
Bracket Hole
DC Power Jack
Join Button
Status LED Indicator
PoE ON/OFF Switch
(ETP-2601T only)
Overview
This devices are High-Speed, long distance Ethernet & PoE extender
that makes possible to transmit the Ethernet signal and PoE via 2-Wire
cable (Twisted pair cable, COM, Power line) in different situations.
It is cost-effective and time saving solution to migrate existing analog
system to IP based system since this device supports easy installation
utilizing the existing cable.
With long distance transmission feature, the device makes to
overcome 100 meters distance limitation easily and reduces the
construction cost significantly compared with fiber optic configuration.
Features
Ethernet over 2-Wire communication following IEEE1901 Standard
Data + Power over 2-Wire cable (UTP, COM, Power Line, etc.)
Supports long distance Untwisted/Twisted 2-Wire cables
Data distance up to 600m
PoE distance up to 300m
Max. 95Mbps Bandwidth (270Mbps between Intercoax 2 series models)
10/100 Full Duplex
128bit AES network encryption
Supports Multi-connection (Daisy chain, Star, etc.)
PoE, PoE+, Extra PoE (Max. 60W output) (ETP-2601T only)
PoE ON/OFF Switch (ETP-2601T only)
LED Indication (Data, Power, Link, PoE)
Plug & Play
Surge Protection
Support PoE+ Input (25.5W) from PSE devices – ETP-2601R Only
Slim design
Quick Start Guide
[Rev.1.0]
ETP-2601T / ETP-2601R
Please read carefully the instruction manual before use. Depending
on the model, the image and the actual look of the product may vary.
LED Indicators
Indicator Color Function
PoE-ON (Tx) ON : PoE Switch On (PoE Output)
OFF : PoE Switch Off
PD-AUX (Rx) ON : PoE Input or Powered by Transmitter
OFF : Powered by adapter
Data-Link Blinking : Ethernet Data Act
Join-Link ETP-Product Link
Power 56V DC Link
Installation Guide
1. Set the IP address on the camera following the instruction manual
of the camera.
Î
If the camera IP is automatically assigned (DHCP, etc.), there is no
need to set the camera IP separately.
2. Fix the enclosed terminal block to the transmitter and receiver, then
connect the 2-wire cable to the transmitter and receiver.
Î
Be sure to connect polarity( , ) carefully. If the connection is
reversed, it will not work.
3. Connect 56V DC power to Transmitter/Receiver first and then to
AC outlet.
Î
Receiver can be powered by PoE Switch Device (PoE+ PD
Supported) but for safe working, it recommeded to use 56VDC
Power supply on Receiver. When using both PoE switch Device and
power supply at the same time, power supply works preferentially.
Î
In case of 7W camera, one 56V DC power can supply up to 300m of
UTP 2-Wire. PoE transmission distance can be varied depending on
cable type and Camera’s power consumption(W).
4. When they are connected without any problem, Power / Join Link
LED are on.
5. Adhere the brackets in the package to Transmitter/Receiver and
then fix up the products.
6. Connect the UTP(LAN) cable between Receiver and NVR first and
then between Transmitter and camera.
7. Turn on the PoE switch on Transmitter for PoE IP camera and if the
camera is powered by a separate power source (not powered by
PoE output feature of the Transmitter), turn off the PoE switch on
Transmitter.
Î
Both Transmitter/Receiver send data and power together via
2-Wire connector. Receiver does not have PoE support so that it
can send data only via RJ45.
8. Ping test is recommended to confirm the whole network after
installation.
9. Check the video signal on the monitor.

Caution
Please install the device following the installation guide.
Do not touch the device and cable with wet hands.
Keep away from moisture and shock.
Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus that produce heat.
Indoor use only.
Do not use for other purposes.
Do not disassemble or modify this device.
Do not put any sticker or paint on it.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Please use the rated power supply for the product.
Connect DC power to this device first and then to AC outlet.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 24 months from the date of
purchase.
If this device is defective or malfunctioning, please unplug the power
adapter immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident, modification
or natural disasters will not be covered manufacturer’s warranty.
How to change the communication password (Coax/UTP/2-Wire)
All Intercoax EoC converters have the same password as factory
defaults setting value and can be used immediately when connecting
to the product (Plug & Play mode).
However, if a number of products are mixed in the same area or
the signal transmission line is in poor condition, the communication
passwords for each equipment (or group) can be set differently to
prevent cross-talk between the lines.
1. Needed items for Joining
EoC Converters / Power supply / Short Cable (Coax, UTP, 2-Wire) /
Paper clip
2. Product configuration
a. Connect EoC Converters with Coax cable (or UTP, 2-Wire) and
power to the one of the converters up with power supply.
b. Check if the Power LED on both devices is ON.
3. Remove the existing password (Unjoining)
This process removes passwords that are entered as factory
defaults.
a. Press the Join button on one of the connected products using a
paper clip until the Power LED turns off and on (Approximately
15 seconds)
b. Remove the existing password by pressing the Join button on the
opposite product in the same way as above.
c. Join LED will be turned off if the password on the devices is
removed correctly.
4. Create New Password (Joining)
New password for communication between connected devices is
created and this will block the communication with other devices (or
group) which have a different password.
a. Press the Join button for 2 seconds on one of the connected
product using a paper clip and the Join LED of the device will
flicker at a constant speed. (Stand-by mode)
b. Press the Join button for 2 seconds on the opposite device in the
same way as above. And then, the Join LED of the device flickers
at a constant speed and both devices restart at the same time.
c. Then the Join-Link lights up and communications are resumed
between the products
5. When adding new products in 1:N configuration to a group that
has already been joined. (Group Joining)
a. Connect new device to the group which is already joined.
(using T-BNC or Y-UTP coupler, Terminal block)
b. Remove the password of the new device in the same way as step
‘3-a’.
c. Press Join button on the one of the device of the existing group
for 2 seconds and Join LED flickers at a constant speed.
d. Press Join button on the new device for 2 seconds and new
device restarts
e. Join-Link lights up and communications are resumed between
the products.
Please visit below website for more detailed information.
Web: http://www.intercoax.com Tel: [phone]~4
E-mail: [email protected] Fax: [phone]
This device complies with part 15 of the fcc rules. Operation is subject to the
following two conditions :
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received including interference
that may cause undesired operation
Applications
AC/DC
Adapter(12V)
Non-PoE IP
Camera
2-Wire Cable
2-Wire Cable
10/100 Ethernet
10/100 Ethernet
PoE
ETP-2601R
56V DC/1.2A
Power Supply
ETP-2601T ETP-2601R
ETP-2601T
PoE
Camera
NVR PoE Switch
Specification
Model ETP-2601T ETP-2601R
Interface 2-Wire 1 x 2-Pin Terminal Block-Ethernet over 2-Wire (T-LinX)
Ethernet 1 x RJ45 - 10/100 Base-T with Auto-detect MDIX
Transmission Rate 95Mbps Full Duplex
(270Mbps between Intercoax 2 series models)
Transmission
Distance
2-Wire up to 600 m(Twisted Pair Cable/Cat.5e)
PoE (PoC) up to 300 m (Cat.5e / 7W camera)
LED
Indication
Ethernet 1 x Data-Link (Yellow)
Data over 2-Wire 1 x Join-Link (Green)
Power 1 x Power On (Amber)
PoE Output 1 x PoE Out (Red)
Encryption 128-bit AES
Power
Input T-Linx or DC12V~57V PoE Switch or
DC48V~57V
PoE Output
IEEE802.3af(PoE),
IEEE802.3at (PoE+),
Extra PoE up to 60W
PoE Not Supported
Power Over 2-Wire Only
PoE Input Not Supported Up to 25.5W (PD)
Mechanical Dimension 80.4(L) x 61.6(W) x 24(H)mm
Weight 102g
Environment
Operating Temp -20 ~ 60°C
Storage Temp -30 ~ 80°C
Relative Humidity 10% ~ 90%
Compliance Certification FCC, CE, KC
Surge Protection IEC 61000-4-5 4kV(1.2 / 50us), 2kA(8 / 20us)
Optional Accessories 56VDC / 1.2A External Power Supply