Interlogix TVD-CB2 User manual

P/N 1073418-EN • REV A • ISS 12FEB18 1 / 4
TVD-CB2 Cup Base Installation
Instructions
Dimensions
Dimensions:
Weight: 200 g (7.02 oz.)
Accessories:
Screw A: 4 pcs
Used to attach the wedge adapter plate to the cup
base.
Supported devices
•TVW-1103/3103
•TVW-1104/3104
•TVW-1105/3105
•TVW-1106/3106
•TVW-1116/3116
•TVW-1130/3130
•TVW-5301
•TVW-5302
•TVW-5303
•TVW-5304
•TVW-5305
•TVW-2101/4101
•TVW-2401/4401
•TVD-SNB Swan Neck Wall Mount
•TVD-PPB Pendant Mount
•TVD-CBW Wall Mount
Installing a TVD-CB2 cup base
to a wedge camera
When installing a TVD-CB2 cup base to a
wedge camera, you require:
•TVD-CB2 cup base
•Wedge adapter plate, included with the
wedge camera

2 / 4 P/N 1073418-EN • REV A • ISS 12FEB18
•Adapter plate mounting screws
To mount a wedge camera to a TVD-
SNB wall mount with a TVD-CB2 cup
base:
1. Pull the camera cables through the
wall mount tube. Attach the swan
neck wall mount to the wall using
the expansion anchors that are
provided with the swan neck mount.
2. Using the four A screws, attach
wedge adapter plate to the cup
base.
3. Screw the cup base onto the swan
neck wall mount and tighten with
the locking screw.
4. Loosen the screws on the wedge
bubble assembly using the Torx
wrench that is supplied with the
camera, and remove the enclosure.
5. Connect the cables to the wedge
camera. Using two screws that are
supplied with the wedge camera,
attach the camera base to the
wedge adapter plate.
6. Re-attach the wedge bubble
assembly to the camera.

P/N 1073418-EN • REV A • ISS 12FEB18 3 / 4
To mount a wedge camera to TVD-
PPB pendant mount with a TVD-CB2
cup base:
1. Screw the pendant mounting plate
onto the pendant mount pipe and
tighten with the locking screw, as
shown.
2. Pull the camera cables through the
pendant mount. Attach the mount
to the ceiling with expansion
anchors that are included with the
pendant mount.
3. Using four screws that are included
with the wedge camera, attach the
wedge adapter plate to the cup
base. Screw the cup base onto the
pendant mount and tighten with the
locking screw.
4. Loosen the screws on the wedge
bubble assembly using the Torx
wrench that is supplied with the
camera, and remove the enclosure.
5. Using two screws that are supplied
with the wedge camera, attach the
camera base to the wedge adapter
plate.
6. Re-attach the camera enclosure to
the camera.
Legal and regulatory
information
Copyright
© 2018 United Technologies
Corporation. All rights reserved.
Interlogix is part of UTC Climate,
Controls & Security, a unit of United
Technologies Corporation.
Trademarks and
patents
The trade names used in this
document may be trademarks or
registered trademarks of the
manufacturers or vendors of the
respective products.

4 / 4 P/N 1073418-EN • REV A • ISS 12FEB18
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa,
CA 92626 5923, USA
Authorized EU manufacturing
representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The
Netherlands
Certification
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED
FOR SALE TO AND INSTALLATION
BY QUALIFIED PROFESSIONALS.
UTC FIRE & SECURITY CANNOT
PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING
ITS PRODUCTS, INCLUDING ANY
“AUTHORIZED DEALER” OR
“AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR
EXPERIENCED TO CORRECTLY
INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty
disclaimers and product safety
information, please check
www.firesecurityproducts.com/policy/p
roduct-warning/ or scan the following
code:
Contact information
and manuals
For contact information go to:
www.interlogix.com or
www.firesecurityproducts.com
To get translations for this and other
product manuals go to:
www.firesecurityproducts.com