International Refrigeration Products WA46YER User manual

WINDOW
AIR CONDITIONER
USER MANUAL
950-0270-revA 9/30/2019
FOR MODELS:
COOLING BTU/h
WA46YER
6,050
WA48YER
8,000
WA410YER
10,200
WA412YER
12,100

Page 1
CONTENTS
INSTALLATION REQUIREMENTS............................................................................................................................2
Tools and Parts..................................................................................................................................................2
Location Requirements......................................................................................................................................3
Electrical Requirements.....................................................................................................................................4
INSTALLATION INSTRUCTIONS..............................................................................................................................5
Prepare Your Unit ..............................................................................................................................................5
Install YourAir Conditioner in the Window.........................................................................................................6
Install the Support Bracket and Seal the Window.............................................................................................7
Install the R1 Hardware.....................................................................................................................................7
AIR CONDITIONER CONTROLS..............................................................................................................................8
Air Conditioner Controls （Panel）...................................................................................................................9
REMOTE CONTROL...............................................................................................................................................11
Function Buttons..............................................................................................................................................12
IMPORTANT INFORMATION..................................................................................................................................13
3 Minute Delay.................................................................................................................................................13
Select ℉or ℃.................................................................................................................................................13
Air Directional Louvers.....................................................................................................................................13
Normal Sounds................................................................................................................................................13
AIR CONDITIONER CARE......................................................................................................................................14
Cleaning the Air Filter ......................................................................................................................................14
Cleaning the Front Panel.................................................................................................................................14
Repairing Paint Damage of Outside Case ......................................................................................................14
Annual Maintenance........................................................................................................................................14
TROUBLESHOOTING.............................................................................................................................................15
SPECIFICATIONS ...................................................................................................................................................17
WARRANTY.............................................................................................................................................................18
FOREWORD
•Inspect unit for shipping damage, mishandling and accessories before installing.
•The appearance of the units that you purchase may be slightly different from the ones described in this manual,
but will not affect proper operations and usage.
•Please read carefully the sections corresponding to the specific model you have, and keep the manual in a safe
place for reference.
•The refrigerant used in your window air conditioner is environmentally safe.
ATTENTION
•Do not modify or otherwise defeat the plug.
•The appliance shall be installed and operated in accordance with National Electrical Code regulations.
•Do not operate the machine when the ambient temperature is below 64°F or above 109°F .
•If the supply cord is damaged, it must be replaced by a qualified person in order to avoid a fire hazard.
•All electrical repairs and connections must be performed by a licensed electrician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic
precautions:
•Plug into a grounded 3 prong outlet.
•Do not remove ground prong.
•Do not use an adapter.
•Do not use an extension cord.
•Unplug air conditioner before servicing.
•Use two or more people to move and install air
conditioner.
•Do not operate this unit if the outdoor
temperature is below 64°F or above 109°F

Page 2
INSTALLATION REQUIREMENTS
Tools and Parts

Page 3
Location Requirements
IMPORTANT: Observe all governing codes and
ordinances.
Check the location where air conditioner will be
installed. Proper installation is your responsibility.
Make sure you have everything necessary for
correct installation.
The location should provide:
•Grounded electrical outlet within 6 ft of
where the power cord exits the air
conditioner.
NOTE:
•Do not use an extension cord.
•Free movement of air in room to be cooled.
•A large enough opening for the air
conditioner.
•Adequate wall support for weight of air
conditioner. Air conditioner weights up to 70
lbs.
NOTE: Cabinet louvers & rear of the air
conditioner must not be obstructed. Air must be
able to pass freely through the cabinet louvers.
The rear of air conditioner must be outdoors. Not
inside a building or garage.
Window Requirements:
These instructions are for
a standard double hung
window. You will need to
modify them for other
types of windows.
The air conditioner can be
installed without the
accordion panel if needed
to fit in a narrow window.
See Window Opening
dimensions.
All supporting parts must be secured to firm
wood, masonry or metal.
Follow the dimension in TABLE -1.
Models/Cooling
Capacity
Dim. A –
Opening Width
Dim. B - Min
Vertical Opening
6,000-8,000
22”-36”
13 1/4”
10,000-12,000
24.4”-38.4”
16.4”
TABLE -1
Thru the Wall Installation Requirements:
The air conditioner can be thru the wall installed.
The side louvers must never be blocked.
Table -2 provides the maximum wall thickness
dimension from the outer case to side air louvers.
Models/Cooling
Capacity
Front Cover to
Side Vent
Unit Depth
6,000-8,000
4.6”
15.7”
10,000-12,000
8.8”
21.5”
TABLE -2
Storm Window Requirements:
A storm window frame will not allow the air
conditioner to tilt properly which in turn will keep
it from draining properly. To adjust for this,
attach a board or piece of wood to the sill. The
board or wood piece should have a depth of at
least 1 1/2”. Make sure the board or piece of
wood is approximately 1/2” higher than the
storm window frame. This will allow the air
conditioner to tilt enough for proper drainage. .

Page 4
Electrical Requirements
LCDI TYPE
Wiring Requirements
NEMA 5-15P
⚫115-Volt (103.5 min to
126.5 max.)
⚫0 to 13amps
⚫15-amp time-delay fuse or
circuit breaker
⚫Use on single outlet circuit
only.
NEMA 6-15P
⚫230-Volt (198 min to 253
max.)
⚫0 to 12 amps
⚫15-amp time-delay fuse or
circuit breaker
⚫Use on single outlet circuit
only.
TABLE - 3
Recommended Grounding Method
This air conditioner must be grounded. This air
conditioner is equipped with a power supply cord
having a grounded 3 prong plug. To minimize
possible shock hazard, the cord must be
plugged into a mating, grounded 3 prong outlet,
grounded in accordance with all local and
national codes. If a mating outlet is not available,
it is the customer’s responsibility to have a
properly grounded 3 prong outlet installed by a
qualified electrical installer.
It is the customer’s responsibility:
•To contact a qualified electrical installer.
•To assure that the electrical installation
is adequate and in conformance with
National Electrical Code, ANSI/NFPA
70- latest edition, and all local codes
and ordinances.
Power Supply Cord
NOTE: Your unit’s device may differ from the
ones shown.
This room air conditioner is equipped with a
power supply cord required by UL. This power
supply cord contains state-of-the-art electronics
that sense leakage current. If he cord is crushed,
the electronics detect leakage current and power
will be disconnected in a fraction of a second.
To Test your power supply cord:
1. Plug power supply cord into a grounded 3
prong outlet.
2. Press RESET
3. Press TEST (listen for click, Reset button
will trip and pop out).
4. Press and release RESET (listen for click;
Reset button will latch and remain in). The
power supply cord is ready for operation.
NOTES:
•The reset button must be pushed in for
proper operation.
•The power supply cord must be replaced if it
fails to trip when the test button is pressed
or fails to reset.
•Do not use the power supply cord as an
off/on switch. The power supply cord is
designed as a protective device.
•A damaged power supply cord must be
replaced with a new power supply cord
obtained from the product manufacturer and
must not be repaired.
•The power supply cord contains no user
serviceable parts. Opening the tamper-
resistant case voids all warranty and
performance claims.

Page 5
INSTALLATION INSTRUCTIONS
Prepare Your Unit
Install the Top Mounting Rail.
•Locate provided bag of screws.
•Remove the tape at back side of sponge,
and then align it at the bottom edge of upper
rail to attach the sponge to the upper rail.
•Use 4 type A screws (See Page 2) to attach
the top mounting rail to the air conditioner.
Note: For some models, the top mounting
rail might be pre-installed to the unit, skip
this step if it is installed.
Install the Accordion Panels
•Hold the accordion panel in one hand and
gently pull back to free the open end.
•Stick one sealing strip respectively on the
left side and right side of accordion panel as
shown below.
•Install the left and right accordion panels into
both sides of the air conditioner respectively.
•Slide the panel all the way in and repeat on
the other side.

Page 6
Stick the sealing strip
Cut the sealing strip into proper length. Tear off the
paster and stick the sealing strip at the lower part of the
window frame. Stick one sealing strip at the outdoor
lower sill
Install Your Air Conditioner in the
Window
•Handle air conditioner gently.
•Be sure your air conditioner does not fall out
of the opening during installation or removal.
•The place where the power cord exits the air
conditioner should be no more than 6 ft (182
cm) from a grounded 3 prong outlet.
•Do not block the louvers on the front panel.
•Do not block the louvers on the outside of
the air conditioner.
Install Your Unit
•Center the air conditioner in window. Check
that lower rail of air conditioner is behind
and against back side of window sill.
Maintain a firm grip on the air conditioner
cabinet. Lower window sash to hold cabinet
in place.
NOTE: Check that air conditioner is tilted back
about 3ºto 4ºdownward to the outside. After
proper installation, condensate should not drain
from the overflow drain hole during normal use,
correct the slope otherwise.
•Measure the distance between the right-
hand side of the cabinet and the inside of
the window channel.
•Repeat for the left side. Adjust the cabinet
until the distance on each side is the same.
•Extend the left and right accordion panels
out against the window frame.
•Use the 5 Type B screws and the Frame
lock (for 10K&12K models only) to fix the
frame of accordion panels at the window
frame and window sill.
6K & 8K model:
10K & 12K model:

Page 7
Install the Support Bracket and Seal the
Window
•Install the fixe bracket of window at the
window frame to fix the window.
NOTE: To prevent the window sill from splitting,
drive the 1/8”pilot holes before driving screws.
•Cut the foam top window gasket to the
window width.
•Stuff the foam between the glass and the
window to prevent air and insects from
getting into the room.
Install the R1 Hardware
In order to minimize air leaks and ensure optimal
insulation, it is necessary to install the included R1
hardware to the side curtain. Follow the instructions
below.
After the unit is installed to the window, measure
the inner width (dimension “L”as below shown) of
the side curtain as shown.
Remark a line on the provided R1 insulation panel
according to the measured width, then cut the R1
insulation panel along the line.
Slide the R1 insulation panel into the side curtain,
the side with pattern should facing the indoor side.
Repeat on the other side.

Page 8
AIR CONDITIONER CONTROLS
Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its
functions then follow the symbol for the functions you desire. The air conditioner can be controlled by the remote or the
control panel.
Unit Control Panel

Page 9
Air Conditioner Controls （ Panel ）
○
1Power button:
Press this button to turn on or turn off the air conditioner.
The unit defaults to operate under Energy Saver mode.
○
2Mode Button
Press this button to select the desired operation mode from Cool, Fan Only, Energy Save as the following sequence.
oCool: In this mode, air conditioner operates the cooling mode. Cooling indicator will be on. Press Fan
Speed button can adjust the fan speed.
oFan Only: In this mode, air conditioner operates the fan mode. The Fan indicator will be on. Press Fan
Speed button can adjust the fan speed. The auto Fan can’t be set in this mode.
oEnergy Saver: In this mode, air conditioner operates the Energy Saver mode. The energy saver indicator
will be on. Press Fan Speed button can adjust the fan speed.
○
3Fan Speed Button:
Press this button can select the desired fan speed from LOW, MED, HIGH, AUTO as the following sequence.
○
4Reset Filter button
After Fan operates for 250 hours, this indicator will be delighted. Clean the filter when the light is on.
○
5Delay 1-24 Hrs button
Press this button to set the TIMER ON and TIMER OFF. The setting indicator will be on during the setting process.
When the unit is ON:
oPress the Delay 1-24 Hrs button once to select the TIMER OFF option to initiate the AUTO-OFF feature.
oPress the “△”or “▽”button to adjust the time for either mode by 1 hour. When the desired time is set, the
unit will automatically store the setting.
When the unit is OFF:
oPress the Delay 1-24 Hrs button once to select the TIMER ON option to initiate the AUTO-ON feature.
oPress the “△”or “▽”button to adjust the time for either mode by 1 hour. When the desired time is set, the
unit will automatically store the setting.
NOTE: To hold the button for more than 2 seconds can change time quickly.
Timer preview:
When the timer is set, you can press the “Delay 1-24 Hrs”button to check the remaining time on display.
Cancel timer:
Press the “Delay 1-24 Hrs”button twice to cancel the timer setting. The timer indicator will be off.
NOTE:
Timer setting range: 1-24h.

Page 10
○
6“△”or “▽”button:
Press this button to change temperature or time.
In temperature setting mode, the temperature will be increased or decreased by 1ºF.
In timer mode, the time will be increased or decreased by 1 hour.
○
7Display:
The display will show the following:
oENERGY SAVER/FAN ONLY/COOL: show the room temp.
oTIMER: shown the setting timer in the first 5s when you setting, and then shows the room temp.
Error Code:
EP: indoor ambient temperature sensor or indoor evaporator temperature sensor error.

Page 11
REMOTE CONTROL
Handling and location of the remote controller
Use the remote controller at a distance of 26 ft., or less, from the appliance. Point it towards the receiver on the air
conditioner. Communication is confirmed with a beep.
CAUTIONS
•The air conditioner will not operate if curtains, doors or other materials block the signal from the remote control to
the air conditioner.
•Avoid
oLiquids
oDirect Sunlight
oExtreme Temperatures
•If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function
properly.
•If other electrical appliances react to the remote controller, either move these appliances or consult your local
dealer.
Replacing Batteries
The remote control is powered by two AAA alkaline batteries housed in the back of the remote. (Do not use
rechargeable batteries)
(1) Remove the cover by pressing down and sliding back.
(2) Remove the old batteries and insert the new batteries, observing polarity.
(3) Replace the battery cover.
Remote Control Specifications
Rated Voltage
3.0V
Lowest Voltage of CPU
Emitting Signal
2.0V
Signal Receiving Range
26 ft
Environment
-41-140︒F
•The illustrations in this manual are for explanation purposes only. The actual shape of remote controller may be
slightly different.
•An audible sound will be heard when the buttons are pressed to change settings or modes.
•When you don’t use remote controller for a long time, please take the batteries out.

Page 12
Function Buttons
○
1 ON/OFF Button: Push this button to start operation, push the
button again to stop operation.
NOTE: The unit will initiate automatically the Energy Saver
function under Cool, Dry, Auto (Only Auto-Cooling and Auto Fan)
modes.
○
2FAN +/- Button:
Select the Fan speed. Press Fan + to increase fan speed and
press Fan –to decrease.
○
3 “▲” and “▼” Button:
Choose the setting temperature as desired. Press the “▲”/“▼”
button to increase/decrease the temperature setting by 1 ºF. To
hold “▲” or “▼” buttons for 2 seconds can change the
temperature quickly.
○
4 Mode button:
Press this button can select the desired operating mode from
Cool, Fan Only, and Energy Save as the following sequence.
oCool: In this mode, air conditioner operates the cooling mode. Cooling indicator will be on. Press Fan
Speed button can adjust the fan speed.
oFan Only: In this mode, air conditioner operates the fan mode. The Fan indicator will be on. Press Fan
Speed button can adjust the fan speed. The auto Fan can’t be set in this mode.
oEnergy Saver: In this mode, air conditioner operates the Energy Saver mode. The energy saver indicator
will be on. Press Fan Speed button can adjust the fan speed.
○
5 Auto button:
Press this button to active the auto fan speed. Air conditioner will select the proper fan speed accordingly.
○
6 +/- Button:
In timer setting mode, press +/- button to increase/decrease the timer setting by 1 hour. Hold the “+/-“button for 2
seconds can change quickly.
○
7 Delay Button:
Press this button can set TIMER ON and TIMER OFF.
When the unit is ON:
oPress the Delay button once to select the TIMER OFF option to initiate the AUTO-OFF feature.
oPress the “+”or “-”button to adjust the time for either mode by 1 hour. When the desired time is set, the
unit will automatically store the setting.
When the unit is OFF:
oPress the Delay button once to select the TIMER ON option to initiate the AUTO-ON feature.
oPress the “+”or “-”button to adjust the time for either mode by 1 hour. When the desired time is set, the
unit will automatically store the setting.
NOTE: To hold the button for more than 2 seconds can change time quickly.

Page 13
IMPORTANT INFORMATION
3 Minute Delay
The Cool function has an automatic 3 minute time delayed start if the unit is turned off and on quickly. This prevents
overheating of the compressor and possible circuit breaker tripping. The fan will continue to run during this time.
Select ℉or ℃
The unit is shipped in degree F as the default indication.
The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius. To convert from one to the
other, press and hold the △and ▽Temp/Delay buttons on control panel simultaneously for 3 seconds.
Air Directional Louvers
Normal Sounds
When your air conditioner is operating normally, you may hear sounds such as:
oDroplets of water hitting the condenser, causing a pinging or clicking sound. The water droplets help to cool
the condenser.
oAir movement, for improved operation.
oClicks from the thermostat cycling.
oVibrations or noise due to poor wall or window construction.
oA high-pitched hum or pulsating noise caused by the modern high-efficiency compressor cycling on and off.
The louvers will allow you to direct the air flow
up or down and left or right throughout the room
as needed. Pivot horizontal louvers until the
desired Up/Down direction is obtained.
Move the Levers from side to side until the
desired Left/Right direction is obtained.

Page 14
AIR CONDITIONER CARE
Your new air conditioner is designed to give you many years of dependable service. This section tells you how to
clean and care for your air conditioner properly. Call your local authorized dealer for an annual checkup. Remember,
the cost of this service call is your responsibility.
__________________________________________
Cleaning the Air Filter
The air filter is removable for easy cleaning. A clean
filter helps remove dust, lint, and other particles from
the air and is important for best cooling and operating
efficiency. Check the filter every 3 weeks to see if it
needs cleaning, or when the filter light is illuminated.
NOTE: Do not operate the air conditioner without the
filter in place.
1. Turn off the air conditioner.
2. Remove air filter.
3. Use a vacuum cleaner to clean air filter. If air filter
is very dirty, wash it in warm water with a mild
detergent. Do not wash air filter in the dishwasher
or use any chemical cleaners. Air dry the filter
completely before replacing to ensure maximum
efficiency.
4. Install the filter.
Cleaning the Front Panel
1. Turn off the air conditioner
2. Remove the air filter and clean it separately. See
Cleaning the Air Filter.
3. Wipe the front panel with a soft damp cloth.
4. Air dry front panel completely.
__________________________________________
Repairing Paint Damage of Outside
Case
Check once or twice a year for paint damage. This is
very important, especially in areas near oceans or
where rust is a problem. If needed, touch-up with a
good grade enamel paint.
NOTE: To reduce paint damage during the winter,
install a heavy duty cover over the air conditioner
cabinet.
__________________________________________
Annual Maintenance
Your air conditioner needs annual maintenance to help
ensure steady, top performance throughout the year.
Call your local authorized dealer to schedule an
annual checkup. The expense of an annual inspection
is your responsibility
4. Replace air filter by sliding filter down into filter
door and closing filter door.
NOTE: Never use hot water over 104 °F to clean the
air filter. Never attempt to operate the unit without the
air filter.

Page 15
TROUBLESHOOTING
Before calling for service, try the suggestions below to see whether you can solve your problem without outside help.
Air conditioner will not operate
1. The power supply cord is unplugged. Plug into
a grounded 3 prong outlet. See “Electrical
Requirements”.
2. The power supply cord has tripped (Reset
button has popped out). Press and release
RESET (listen for click; Reset button will latch and
remain in) to resume operation.
3. A household fuse has blown, or a circuit
breaker has tripped. Replace the fuse or reset
the circuit breaker. If the problem continues, call
an electrician. See “Electrical Requirements”.
4. Depending on model, the Power button has
not been pressed or the Fan control is turned
to OFF. Press POWER or turn the Fan control to
an active setting.
5. The local power has failed. Wait for power to be
restored.
Air conditioner blows fuses or trips circuit
breakers
Too many appliances are being used on the same
circuit. Unplug or relocate appliances that share the
same circuit.
Time delay fuse or circuit breaker wrong capacity
is being used. Replace with a time delay fuse or
circuit breaker of the correct capacity. See “Electrical
Requirements”.
An extension cord is being used. Do not use an
extension cord with this or any other appliance.
You are trying to restart the air conditioner too
soon after turning the unit off. Wait at least 3
minutes after turning the unit off before trying to restart
the air conditioner.
Air conditioner power supply cord trips
(Reset button pops out)
Disturbances in your electrical current can trip
(Reset button will pop out) the power supply cord.
Press and release RESET (listen for click; Reset
button will latch and remain in) to resume operation.
Electrical overloading, overheating, pinched cord
can trip (Reset button will pop out) the power
supply cord.
After correcting the problem, press and release
RESET (listen for click; Reset button will latch and
remain in) to resume operation.
NOTE: a damaged power supply cord must be
replaced with a new power supply cord obtained from
the product manufacturer and must not be repaired.
Air conditioner runs too long
The current air conditioner replaced an older
model. The use of more efficient components may
cause the air conditioner to run longer than an older
model, but the total energy consumption will be less.
Newer air conditioners do not emit the blast of cold air
you may be accustomed to from older units, but this is
not an indication of lesser cooling capacity or
efficiency. Refer to the efficiency rating (EER) and
capacity rating (in BTU/hr.) marked on the air
conditioner.
The air conditioner is in a heavily occupied room,
or heat-producing appliances are in use in the
room. Use exhaust vent fans while cooking or bathing
and try not to use heat producing appliances during
the hottest part of the day. A higher capacity air
conditioner may be required, depending on the size of
the room being cooled.

Page 16
Air Conditioner cycles on and off too
often, or does not cool room in cooling
mode
The air conditioner is not properly sized for your
room.
Check the cooling capabilities of your room air
conditioner. Room air conditioners are not designed to
cool multiple rooms.
The filter is dirty or obstructed by debris. Clean the
filter.
The inside evaporator and outside condenser coils
are dirty or obstructed by debris. See “Annual
Maintenance.
There is excessive heat or moisture (open
container cooking, showers, etc.) in the room. Use
a fan to exhaust heat or moisture from the room. Try
not to use heat-producing appliances during the
hottest part of the day.
The louvers are blocked. Install the air conditioner in
a location where the louvers are free from curtains,
blinds, furniture, etc.
The outside temperature is below 64ºF (18ºC). Do
not try to operate your air conditioner in the cooling
mode when the outside temperature is below 65ºF
(18ºC).
The temperature of the room you are trying to cool
is extremely hot. Allow extra time for the air
conditioner to cool off a very hot room.
Windows or doors to the outside are open. Close
all windows and doors.
The Vent control is set to open (on some models).
Push the Vent control to CLOSED for maximum
cooling and/or heating.
The temperature set point or
Thermostat control is not at a cool enough setting.
Adjust the temperature set point to a cooler setting by
pressing the minus button to reduce the temperature
or adjust the Thermostat control to a cooler setting by
turning the knob clockwise. Turn the Fan control to
HIGH or Turbo Cool.
Temperature on display does not match
room temperature
When the compressor and fan motor turn off
during Power Saver mode, or after you turn off the
unit, a lower temperature reading than the actual
room temperature may be displayed for a short
period of time. This lower temperature reading is
caused by the temperature sensor being located close
to the cold evaporator coil. The actual room
temperature will display within a few minutes.
Water drips from cabinet into your house
The air conditioner is not properly leveled. The air
conditioner should slope slightly downward toward the
outside. Level the air conditioner to provide a
downward slope toward the outside to ensure proper
drainage. See the Installation instructions.
NOTE: Do not drill a hole into the bottom of the metal base and condensate pan.

Page 17
SPECIFICATIONS
NOTE:
1) Product specification subject to change without notice.
2) Above 109 °F unit will still operate but efficiency starts to decline.
IRP Model No.
WA46YER
WA48YER
WA410YER
WA412YER
Product Code
421-0100
421-0101
421-0102
421-0103
Cooling Capacity
6,050
8,000
10,200
12,100
Rated Voltage
115
115
115
115
CEER Rating
12.1
12
12
12
EER Rating
12.3
12.1
12.1
12.1
Dehumidification (pints/hr)
1.27
1.9
2.6
3.72
Max Air Flow (CFM)
177
224
288
288
Operating Voltage Range
103.5-126.5
103.5-126.5
103.5-126.5
103.5-126.5
Frequency/Cycle
60 HZ
60 HZ
60 HZ
60 HZ
Cooling Amps
4.6
6
7.8
9.2
Cooling Watts
490
660
840
1000
Plug Type –LCDI
5-15P
5-15P
5-15P
5-15P
Power Cord Rating (amps)
10
13
13
15
Power Cord Length (ft)
6
6
6
6
Refrigerant Charge - R410a (oz.)
14.82
16.2
20.46
24.69
Max dbA Level (Indoor/Outdoor)
65/67
69/72
69/77
69/77
4 Way Air Adjustment
Yes
Yes
Yes
Yes
2 Way Air Swing
Yes
Yes
Yes
Yes
Air Discharge
Top Front
Top Front
Top Front
Top Front
Compressor Capacitor
45μF
55μF
55μF
65μF
Fan Motor Capacitor
6μF
15μF
15μF
15μF
Controls
Remote
Remote
Remote
Remote
Ambient Operating Temperature
64-109 °F
64-109 °F
64-109 °F
64-109 °F
Unit Width
18.6”
20.9”
21.3”
21.3”
Unit Depth
15.7”
15.8”
21.5”
21.5”
Unit Height
12.8”
12.8”
15.7”
15.7”
Window Width Opening
22”-36”
22”-36”
24.4”-38.4”
24.4”-38.4”
Thru. Wall Max. Thickness
4.6”
4.6”
8.8”
8.8”
Chassis Slide Out
No
No
No
No
N.W. /G.W. (Lbs)
46.3/52.9
52.9/59.5
66.1/73.9
71.5/79.2
Energy Star
Yes
Yes
Yes
Yes

Page 18
WARRANTY
International Refrigeration Products warrants that the product supplied is free from defects in
material and workmanship. This warranty is valid as long as this product is properly handled,
installed, operated and serviced in accordance with the Installation and Operating Instructions
shipped with this unit, and the warranty card is completed and mailed no later than 30 days after
date of purchase. All warranty claims must be made within one (1) year for spare parts and
compressor from date of purchase (unless national regulations require a longer registration period).
Warranty coverage:
1) LABOR IS NOT COVERED.
2) OUT OF CARTON ISSUES MUST BE REPORTED WITHIN ONE DAY.
3) PARTS ARE COVERED FOR 1 YEAR.
4) COMPRESSORS ARE COVERED FOR 1 YEAR.
5) NORMAL WEAR AND TEAR IS NOT COVERED.
Additional claims are excluded, unless required by national regulations. International Refrigeration
Products Inc. is not responsible for incidental, consequential, direct, or indirect damages, or
expenses relating to the use of, or the inability to use the product for any purpose. Other implied
warranties are excluded.
This constitutes International Refrigeration Products’ warranty obligation and replaces any and all
prior warranties for this product.
International Refrigeration Products Inc
1035 Wheeler Way
Langhorne, PA 19047
Service - Tel: [phone] Fax: [phone]
Hours: 8:00 AM to 4:30 PM EST
Website: www.irproducts.biz