Interphone stereo F4 S User manual

1
3
4
2
6
5
6
www.interphone.cellularline.com
A
A
B
B B
QUICK GUIDE EN
www.interphone.cellularline.com - www.cellularline.com
Export Dept. [email protected]
A- YELLOW
B - GREEN
for installation of audio kit refer to the help available
www.interphone.cellularline.com
1 - Multipurpose button
2 - Multipurpose LED
3 - Volume adjustment button +
4 - Volume adjustment button -
5 - Recharge / Multipurpose socket and
accessories
6 - Bluetooth® control panel connection guide
7 - Speaker
8 - Microphone
ASSEMBLY OF THE SLIDE SUPPORT
WITH REMOVABLE CLIP
Take the support and note the best place
to fasten it to the side of the helmet. Insert
the rear part of the clip into the helmet and
couple the other part on the outside.
Insert the screws and tighten gently.
ASSEMBLY OF THE ADHESIVE SLIDE
SUPPORT
Take the adhesive support and look for the
best side and place to position it. Clean and
de-grease the part of the helmet where you
are going to stick the support (do not use
any detergents that could damage the hel-
Check position and move
the support if necessa-
ry, by sliding it along.
Tighten the screws with
the screwdriver supplied.
met’s nish). Remove the
protective lm from the
bi-adhesive, and apply the
support to the helmet.
As the support will not be
able to be moved once
stuck onto the helmet,
take great care with its po-
sitioning, when applying.

SPVINTERPHONEF4
MICINTERPHONEF4
ULTRASLIMF4FFKIT
MICINTERPHONEF4UNI
MICINTERPHOF4MP3
MICINTERPHONEF4FF
CUSBINTERPHONEF4
TESTKITINTERPHONE
ACHEUINTERPHONEF4-UK-AUS-JP
CBRARINTERPHONEF4
INTERPHONEF ACCESSORIES
Congratulations on your purchase of the InterphoneF4S.
Before using this product, we recommend you carefully perform the operations
outlined in this Quick Guide.
1 - Charging
Plug the battery charger into a 110/220 V socket.
Insert the plug on the battery charger into the connector on the InterphoneF4S.
The LED lights up red during charging.
The LED turns green when charging is complete.
When charging is complete, disconnect the unit from the charger by pulling out
the plug, and also pull out the charger from the mains socket.
2 - Setup
With InterphoneF4S o, press and hold the multifunction button for approx. 8 se-
conds until the LED ashes blue and red alternately .
With the LED ashing red/blue, search for devices from the phone (refer to the mo-
bile phone or navigator instruction manual).
6 - Telephone + stereo function A2DP
With this combination, the connection to the telephone function takes priority.
• During a telephone conversation, the playing of music is not permitted.
• When listening to music, you can answer a telephone call received. Press and
release the MFB button to enable the call. At the end of the call, music will auto-
matically continue playing from the exact point at which it had stopped.
• To refuse a call, press and hold the MFB button for approximately four seconds.
• To adjust the volume, press the buttons Volume + or Volume -, depending on
the desired volume level.
N.B.: In telephones equipped with musical players, and therefore which include a Ste-
reo (A2DP) prole, the Telephone + Stereo (A2DP) function coincides.
7 - Intercom - Pairing
After having turned the two InterphoneF4S o, press and hold the MFB buttons
on both until the warning light alternates red and blue ashes. This will take about
8 seconds.
When both LEDs ash red/blue alternately, press and release the MFB button on
one of the two InterphoneF4S.
The two InterphoneF4S are connected when both LEDs show a xed blue light.
8 - Intercom function
To enable intercom function: to enable the conversation in an intercom prole,
press the MFB button on one of the two InterphoneF4S, and hold for about 3 se-
conds. An audible warning will advise you when connection has occurred.
Conversation in intercom mode is full-duplex.
To disable intercom function: to disable intercom function, simply press and re-
lease the MFB button.
9 - Bluetooth® specications®
Bluetooth®:
v2.1 EDR
Supported proles:
Headset – Handsfree – A2DP / AVRCP / SBC
3 - Connecting to a phone
From the Bluetooth menu on your mobile phone (such as the sample iPhone menu
shown below), search for a new device.
When the device is found, select InterphoneF4S. Connection will take place
automatically after a few seconds.
If a password is required, enter 0000.
4  Telephone Function
To answer a call: as a call comes in, the speaker produces a warning sound or the
telephone’s ring: to answer, simply press and release the MFB button.
To end a call: to end a call, simply press and release the MFB button.
Vocal call: some telephones allow you to make a vocal call simply by pressing and
releasing the MFB button.
To refuse a call: to refuse the call, press and hold the MFB button for approximately
4 seconds.
To refuse a call in VOX mode, follow the instructions given in the VOX FUNCTION
section.
Volume adjustment: to adjust the volume, press the buttons Volume + or Volu-
me -, depending on the desired volume level.
5 - Music remote control
Play/Pause: press and release the MFB button twice.
Rew: press and hold the Volume - button for 3 seconds.
FF: press and hold the Volume + button for 3 seconds.
Volume: To adjust the volume, press the buttons Volume + or Volume -, depen-
ding on the desired volume level.
Interphone F4S
Interphone F4S
Interphone F4S