Intraphex P1N-GM11 User manual

P1n-gm11
INSTALLATION
MANUAL
Prodigy*one.2
navigation
INTEGRATION MODULE
This manual shows the install into a gmc terrain. Other
vehicle disassembly will vary. wiring remains the same
with all vehicles.
See application guide for applicable vehicles

www.INTRAPHEX.com
SUPPOR[email protected]
SUPPORT: 810.355.2266
EXT 4
Fax: [phone]
FACETIME VIDEO TECH SUPPORT:
[email protected]
Contacts

What’s In The Box
Contents
 VIDEO INTERFACE
 PRODIGY*ONE.2
 MAIN T-HARNESS
 GVIF T-HARNESS
 MONITOR T-HARNESS
 8GB SD CARD WITH
INTRAPHEX NAV
SOFTWARE
 INSTALL/USERS
GUIDES
 GPS ANTENNA
 MICROPHONE
 INTRAPHEX MOUSE
 CONNECTOR TWO

INTERFACE DIP SWITCH SETTINGS
DIP ON OFF
DIP 1 A/V 1 ON A/V 1 OFF
DIP 2 A/V 2 ON A/V 2 OFF
DIP 3 A/V 3 ON A/V 3 OFF
DIP 4 AFTERMARKET CAMERA OEM CAMERA
 DIP SWITCH SETTINGS MUST BE PERFORMED WITH UNIT POWERED OFF.
IT WILL NOT CAUSE DAMAGE, BUT THE FUNCTION WILL NOT BE
RECOGNIZED UNTIL POWER CYCLES.
A/V FUNCTIONS
 THIS UNIT SUPPORTS THREE AUDIO/VIDEO INPUTS. AND ONE
AUDIO/VIDEO OUTPUT.
 WHEN USING A/V FUNCTIONS, YOU CAN CONFIGURE THE AUDIO TO BE
PASSED DIRECTLY FROM A/V SOURCE TO VEHICLES “AUX IN” BY
CONNECTING THE “A/V OUT” TO THE “AUX IN” RCAS LOCATED ON THE
44 PIN T-HARNESS, AND ENABLING THE “AUX IN” SETTING IN THE
INTERFACE MENU. THERE WILL BE NO NEED FOR THE USER TO PRESS
“AUX SOURCE” BECAUSE THE INTERFACE WILL DO THIS AUTOMATICALLY
WHEN IT IS SWITCHED INTO A/V 1,2,3.

RADIO CONTROL PANEL
BUTTON FUNCTIONS
 BUTTON FUNCTIONS ARE DETERMIDED BY THE “VEHICLE” TYPE CHOSEN
IN THE INTERFACE SETTINGS MENU. IF THEY ARE NOT PERFORMING AS
STATED IN THE TABLE BELOW, ENTER THE SETTINGS MENU AND
CHANGE “VEHICLE” TYPE.
BUTTON WHEN PRESSED IN NAV SCREEN WHEN PRESSED IN FACTORY
SCREEN
HOME 1 SEC = SWITCH BETWEEN A/V SOURCE 3 SEC = SWITCH TO INTERFACE
BACK SWITCH TO PREVIOUS FACTORY SCREEN FACTORY FUNCTION
TONE SWITCH TO FACTORY AUDIO SETTINGS FACTORY FUNCTION
PHONE SWITCH TO PHONE FACTORY FUNCTION
SOURCE THIS WILL SWITCH SOURCE WITHOUT
EXITING NAV SCREEN FACTORY FUNCTION
INFO NO FUNCTION FACTORY FUNCTION
FAV THIS WILL SWITCH FAVORITES WITHOUT
EXITING NAV SCREEN FACTORY FUNCTION
|<< >>| THIS WILL SEEK WITHOUT EXITING NAV
SCREEN FACTORY FUNCTION
|> / || THIS WILL PLAY/PAUSE WITHOUT EXITING
NAV SCREEN FACTORY FUNCTION
MUTE THIS WILL MUTE AUDIO WITHOUT EXITING
NAV SCREEN FACTORY FUNCTION

 REMOVE MONITOR HOOD BY PULLNG
UP ON FRONT. SET ASIDE.
 REMOVE RADIO CONTROL PANEL.
GENTLY PULL PN LOWER PART OF PANEL
TO RELEASE, THERE ARE NO SCREWS.
UNPLUG HVAC/RADIO CONNECTOR. SET
ASIDE.
 REMOVE FOUR 7MM SCREWS SECURING
FACTORY MONITOR IN PLACE. UNPLUG
GVIF (BLUE) AND POWER HARNESS. SET
ASIDE.
 REMOVE UPPER CENTER CONSOLE TRIM
BEZELS (LEFT AND RIGHT). THERE ARE
NO SCREWS, THEY PULL STRAIGHT OUT
TOWARDS THE REAR OF THE VEHICLE.
SET ASIDE.
*GMC TERRAIN DISASSEMBLY SHOWN, OTHER VEHICLES WILL VARY

 REMOVE FOUR 7MM SCREWS
HOLDING CD/12VOLT POCKET IN
PLACE. PLACE SHIFTER IN “D”
POSITION, AND REMOVE POCKET.
UNPLUG 12VOLT SOCKET. SET ASIDE.
 REMOVE FOUR 7MM SCREWS
HOLDING LOWER SECTION OF UPPER
DASH. THIS WILL ALLOW THE DASH TO
FLEX TO REMOVE THE FACTORY
RADIO/CD.
 REMOVE FOUR 7MM SCREWS
HOLDING FACTORY RADIO/CD IN
PLACE. TWO ARE LOCATED INSIDE
CUTOUT SHOWN. THE OTHER TWO
ARE LOCATED ON SIDES OF RADIO.
 GENTLY PULL OUT ON DASH PANEL
AND REMOVE RADIO/CD. UNPLUG ALL
CONNECTORS AND SET RADIO ASIDE.

 ALL COMPONETS REMOVED FROM
DASH.
 REMOVE PASSENGER SIDE OF CENTER
CONSOLE. NO SCREWS, JUST CLIPS. SET
PANEL ASIDE.
 ROUTE GVIF T-HARNESS FROM FACTORY
LOCATION DOWN TO PASSENGER
FLOOR BOARD NEAR FUSE BOX.
 ROUTE MONITOR T-HARNESS TO
LOCATION BEHIND FACTORY RADIO. IT IS
NECISSARY TO RUN THESE TWO CABLES
BEHIND PLACTIC SUBFRAME, AS THERE
IS NO ROOM FOR THEM ON TOP
DURING RE-ASSEMBLY.

 PLUG BOTH T-HARNESSES INTO
FACTORY CONNECTORS, AND TUCK
HARNESS INSIDE OF SUBFRAME
LEAVING ONLY THE TWO MALE
CONNECTORS FOR THE MONITOR OUT.
 PLUG MONITOR T-HARNESS 4PIN INTO
44PIN MAIN T-HARNESS.
 ROUTE WHITE CONNECTORS FROM
44PIN MAIN T-HARNESS BEHIND
PLASTIC DOWN TO PASSENGER FLOOR
BOARD.
 HARNESS ROUTED.

 PLUG TWO CONNECTORS INTO
INTERFACE. THE OTHER CONNECTORS
SHOWN IN THIS PICTURE (3PIN & 2PIN)
ARE FOR DVD IR AND ARE NOT NEEDED
UNLESS INSTALLING AN AFTERMARKET
DVD PLAYER NEEDING TOUCH
CONTROL.
 PLACE INTERFACE UNDER FUSEBOX AS
SHOWN IN THE PICTURE. SECURE WITH
HOOK AND LOOP FASTENER. THIS WILL
LEAVE THE “GAIN”,”GVIF”, “DIPS”, AND
“A/V CONNECTOR” EXPOSED.
 PLUG GVIF T-HARNESS INTO GVIF
SOCKET. THERE ARE GUIDES LOCATED
ON PLUG TO ALIGN IT CORRECTLY. BE
SURE TO PLUG IN CORRECTLY. DO NOT
FORCE. ROUTE THE CABLE BEHIND FUSE
BOX AND SECURE WITH CABLE TIES.
 ROUTE CABLES BEHIND FUSEBOX,
ALLOWING THE CONNECTORS TO EXIT
ON THE BOTTOM. THIS IS WHERE THE
INTERFACE WILL RESIDE.

 ROUTE 24PIN BLACK CONNECTOR FOR
PRODIGY*ONE.2 FORWARD. PLUG INTO
PRODIGY*ONE.2 (PRODIGY*MINI
SHOWN). PLUG 20PIN “CONNECTOR
TWO” INTO PRODIGY*ONE.2. ROUTE
OPEN USB TO ACCESSABLE LOCATION
FOR MOUSE.
 ROUTE MICROPHONE AND GPS
ANTENNA FROM DESIRED LOCATIONS
AND CONNECT TO PRODIGY*ONE.2.
GPS ANTENNA CAN BE MOUNTED
UNDER PLASTIC, BUT NEEDS A CLEAR
VIEW OF THE SKY. MICROPHONE
PERFORMS BEST ON DRIVERS A-PILLAR.
 PLUG IN 44PIN MAIN T-HARNESS.
CHECK TO MAKE SURE NO PINS
BACKED OUT. LOCATE PLUG BEHIND
PLASTIC AND ARRANGE T-HARNESS SO
THAT FACTORY RADIO CAN BE
REPLACED. IT IS VERY TIGHT AND MAY
TAKE SOME CONFIGURING.
 INSERT ALL CONNECTORS PREVIOUSLY
REMOVED BACK INTO RADIO/CD AND
REINSTALL INTO DASH. TAKE YOUR
TIME, *TIP* USE HAND FROM BOTTOM
OF RADIO TO REACH UP AND HELP
ALIGN CABLES SO THE RADIO SEATS
PROPERLY IN DASH.

 PLUG GVIF AND MONITOR T-HARNESS
INTO FACTORY MONITOR AND
REMOUNT MONITOR WITH FOUR 7MM
SCREWS.
 REPLACE THE RADIO CONTROL PANEL.
AT THIS POINT YOU SHOULD BE ABLE TO
PERFORM SETUP AND ADJUSTMENTS,
BEFORE RE-ISTALLATION OF ALL TRIM
PANELS.
 TURN ON KEY TO THE IGN POSITION
AND PRESS THE “HOME” KEY FOR THREE
SECONDS. THE INTERFACE SHOULD
SWITCH TO THE “NAVI” SCREEN.
(TOUCH WILL NOT WORK YET) IF
“HOME” KEY DOES NOT WORK TRY THE
“TONE” KEY. YOU WILL SET THIS UP CORRECTLY
ONCE INSIDE OF INTERFACE SCREEN.
 ONCE INSIDE OF INTERFACE SCREEN
(YOU WILL SEE MAIN MENU) PRESS
AND HOLD TOUCH SCREEN IN ANY
LOCATION FOR ABOUT 10 SECONDS.
YOU WILL ENTER THE “ON SCREEN
MENU” FOR THE INTERFACE.

 ONCE INSIDE THIS MENU, IT WILL BE
NECISSARY TO SET THE INTERFACE UP
FOR DESIRED OPERATION. CHOOSE
VEHICLE TYPE. THIS WILL CHOOSE
HOW RADIO CONTROL BUTTONS
FUNCTION. SEE FUNCTION DIAGRAM
 NAVI SWITCH MODE WILL ENABLE OR
DISABLE THE INTELLIFLIP FEATURE OF
THE INTERFACE. IF SET TO AUTO, THE
INTERFACE WILL SWITCH BACK TO THE
FACTORY SCREEN AFTER 60 SECONDS
OF NO NAVIGATION COMMANDS,
THEN AUTOMATICALLY SWITCH BACK
TO NAVI WHEN THE NAVIGATION
SPEAKS AGAIN.
 GM AUX CONTROL WHEN ENABLED
WILL TUNE THE FACTORY RADIO TO
“AUX” WHEN VIDEO ONE IS SELECTED
IN THE INTERFACE. AND SWITCH THE
RADIO BACK “RADIO” WHEN
INTERFACE IS SWITCHED TO “RGB” OR
“FACTORY MODE” THIS IS TYPICALLY
USED WHEN INSTALLING A SEPARATE
A/V SOURCE IN A/V 1.
 ONCE DESIRED SETTINGS ARE MADE
THEN PRESS EXIT AND SAVE “YES”.
TYPE 1 EQUINOX, TERRAIN, CRUZE, ECT
TYPE 2 MALIBU

 ENTER PASSWORD “7777” THEN PRESS
OK TO ENTER SETTINGS MENU.
 CLICK ON THE “CALIBRATION” ICON.
TOUCH SCREEN CALIBRATION
 USING THE MOUSE (PLUGGED INTO THE
OPEN USB FROM EARLIER) CLICK ON
THE SETTINGS TAB.
 NOW USING YOUR FINGER (FROM DRIVER
SIDE OF CAR FOR BEST RESULTS) TOUCH AND
RELEASE THE CROSS IN ALL FIVE
LOCATIONS. THEN YOU CAN PRESS THE
EXIT BUTTON. AT THIS POINT YOU CAN
REMOVE THE MOUSE AS IT IS NO
LONGER NEEDED.

 DO NOT CHANGE ANY OF THE OTHER
SETTINGS INSIDE OF THE SETTINGS
MENU. THEY ARE ALL SET TO DEFAULT.
CHANGING ANY OF THESE SETTINGS
WILL CAUSE ERRATIC BEHAVIOR OR
CAUSE THE SCREEN TO GO BLACK. IF
THIS HAPPENS CALL TECH SUPPORT
FOR ASSISTANCE.
NAVIGATION SOFTWARE
 LOCATE THE ENVELOPE CONTAINING
THE NAVIGATION SOFTWARE. OPEN
AND REMOVE THE SD CARD, PLACE SD
CARD INTO THE PRODIGY*ONE.2
MODULE.
 ONCE SD CARD IS INSERTED INTO
MODULE, LOCATE “SD CARD DOOR”
AND TWO SCREWS AND INSTALL THE
COVER OVER THE SD CARD SLOT.

 USING THE VOLUME SETTING FOR
VOICE, YOU CAN PRESS THE CIRCLE AND
IT WILL REPEAT A PROMPT SO THAT
YOU CAN SET THIS CORRECTLY. CHOOSE
AN OUTPUT THAT COMPLIMENTS THE
RADIO VOLUME OUTPUT.
 THE USER WILL STILL HAVE VOLUME CONTROL FROM THE VOLUME
SLIDER BAR LOCATED IN THE VOLUME SETTINGS.
 **NOTE** THE RADIO’S VOLUME KNOB WILL HAVE NO AFFECT ON
OUTPUT, UNLESS IN THE “ALL THE WAY DOWN” POSITION, AS THIS WILL
MUTE THE FACTORY AMP CAUSING NO SOUND TO BE HEARD.
 DEPENDING ON WETHER THE VEHICLE HAS A FACTORY AMP OR NOT,
THE GAIN ADJUSTMENT MAY VARY. THERE IS AN INTERNAL 20X2
AMPLIFIER BUILT INSIDE OF THE INTERFACE TO ACCOMIDATE EITHER
SITUATION.
 LOCATE GAIN CONTROL ON INTERFACE.
USING A SMALL SCREW DRIVER YOU
CAN ADJUST THE OUTPUT OF THE
NAVIGATION VOLUME.
ADJUSTING THE GAIN

RE-ASSEMBLY
 ONCE PROPER FUNCTION HAS BEEN ACHIEVED, YOU CAN RE-ASSEMBLE
THE VEHICLE.
 BE SURE TO REPLACE ALL REMOVED SCREWS AND TRIM PANELS.
 BE SURE TO LEAVE NAVIGATION QUICK START GUIDE AND USER
INSTRUCTIONS IN THE VEHICLE FOR THE CUSTOMER.

SCAN THE IMAGE ABOVE WITH YOUR MOBILE PHONE TO GET MORE
INFORMATION ABOUT INTRAPHEX PRODUCTS