Inviting Homes Salt Lamp User manual

Salt Lamp Speaker
Instruction Manual
Please carefully read the safety instructions before using the salt lamp.

Table of Contents
•Safety Guide
•Introduction
•Part Names
•Preparations
•Listening to Music Via Bluetooth Connection
•Listening to External Sources
•Troubleshooting
•Care and Maintenance
•Specifications
•Terms of Use

Safety Guide
• BREAKABLE: Handle with care.
• NOT FOR HUMAN CONSUMPTION.
• BEFORE FIRST USE: Inspect lamp. DO NOT USE if lamp, cord, plug, or parts are damaged or defective.
• Always turn off all controls before unplugging the lamp.
• Always unplug lamp before handling, cleaning, removing, replacing, or adjusting parts.
• Keep away from water.
• DO NOT USE if lamp has been wet or exposed to water as this may result in electric shock or electrocution.
• Avoid using the lamp in high humidity environments.
• Intended for indoor use only.
• Unplug lamp before adjusting or removing parts.
• WARNING: KEEP OUT OF REACH OF CHILDREN AND PETS.

Introduction
•Confirm the package contents and thoroughly read this manual before using your lamp.
•For your own safety, please follow the instructions for daily usage and maintenance.
•Illustrations may differ from the actual item depicted.
•NOTE: Always place Himalayan Salt Lamps on top of a coaster, placemat, tray, or similar item to protect your
furniture. Himalayan Salt Lamps sometimes “sweat” which may damage furniture and certain types of wood.
•Step 1: Place the lamp on a flat and stable surface. Keep out of reach of children and pets.
•Step 2: Plug in your lamp.
•Step 3: If your lamp includes a dimmable switch, adjust the lighting to your desired level of brightness.
•Step 4: Unplug the lamp when not in use for extended periods of time.
•Supplied Accessories: 110V 60Hz 15W Incandescent Light Bulb

Part Names
Speaker Power
-Press and hold to turn the speaker ON/OFF
Mode Selection
-Press to switch between Bluetooth (Blue indicator light will turn on) or AUX
(Red indicator light will turn on)
-Press and hold to reset Bluetooth
Volume -
-Press and hold to decrease the volume
-The lamp plays a tone when it reaches the maximum volume level
④Volume +
-Press and hold to increase the volume
-The lamp plays a tone when it reaches the minimum volume level
⑤Light Power and +/-
-Press to turn the light ON/OFF
-Press and hold to adjust the lamp’s brightness
⑥Indicator
-Blue light on: Bluetooth mode
-Blue light blinking: Bluetooth disconnected and waiting for pairing
-Red light on: AUX mode
⑦Loudspeaker
⑧Light cup
⑨Bulb Cap
⑩Incandescent Light Bulb
⑪AUX
-Connects to an external device via a commercially available 3.5 mm stereo
mini jack.
⑫AC IN
⑬AC Power Switch
-Completely turn on or shut off internal power supply
⑭Condensate water drainage

Preparation
•Open the packaging
•Once the lamp is removed from the box and before plugging in to a power outlet,
pull the bulb cap (⑨) upward to check if the bulb is in good condition. If yes, place
the bulb cap back into position and proceed to the next step. If not, please carefully
replace the light bulb.
•Turn on the light and the speaker
•First, turn on the AC power switch (⑬). Second, press the light power button (⑤),
and the light will then turn on.
•Press the speaker power button (). The indicator light will then turn on. The lamp
will play a startup tone when it is turned on. You should see a blue indicator light (⑥)
blinking that signals the lamp is ready for pairing.
•Placing the salt chunks
•Turn off the power switch and unplug the lamp from the wall outlet. Carefully place
the salt chunks into the clear cylinder (⑧). The salt lamp speaker is ready for use
once the salt chunks reach the rim of the cylinder without falling out.

Pairing and Playing Back Music
1. Press to turn on the speaker.
2. The indicator light will begin blinking in blue.
3. Turn on the Bluetooth function on your device.
4. Find “INVITING HOMES L-1” in the device list and tap it to pair.
5. After pairing is complete, the indicator light will stop blinking and light up
in blue. The unit plays a Bluetooth connection tone when a Bluetooth
connection is established.
6. You may now play back music through your device.
If another device is already connected to the unit, terminate that Bluetooth
connection by pressing and holding M for 3 seconds. You should then see the indicator
light blinking blue. You may now pair it with the new device.

Listening to External Sources
•The lamp allows for the playback of external devices connected to the AUX terminal. A commercially
available 3.5 mm mini-plug cable is required for this connection. Be sure to turn off the lamp by
pressing the power button before connecting the external device.
1. Turn off the lamp
2. Plug the cable into the AUX terminal of the lamp
3. Connect the other end of the cable to the external device
4. Turn on the lamp
5. Press M and allow the red indicator light to turn on
6. Play back music on your external device
7. Lower the volume of the lamp and the external device before connecting

Troubleshooting
Problem Cause Solution
The lamp cannot be turned on.
The lamp does not operate properly.
The power outlet is not properly connected. Connect the power outlet firmly.
The AC power switch on the back of the lamp is
turned OFF.
Turn the AC power switch ON.
The bulb is not turning on. The incandescent bulb is broken. Change the bulb.
The light is not switched to ON. Turn the light on using button ⑤on the front
control panel.
The speakers make no sound when connected
through Bluetooth.
The Bluetooth connection is not stable or is
disconnected.
Make sure the connecting device is within 10m (33
ft) of the lamp.
Check the connecting device for the connection
status.
The volume of the unit and/or connecting device is
set too low or muted.
Adjust the volume of the lamp and connecting
device to a proper level.
The speakers make no sound in AUX connected
mode.
3.5mm cable is not connected properly or the
volume set is too low.
Check the cable and adjust the volume to a proper
level.
The buttons are not functioning. The MPU of the lamp is not working properly. Turn off the AC power switch then wait for 20
seconds and restart the lamp.

Care and Maintenance
•Always turn off the lamp and unplug it
before cleaning.
•Let the lamp cool down before
cleaning.
•Periodically wipe down your lamp
with a clean and dry cloth to remove
any moisture or dust particles that
may have accumulated.
•DO NOT clean lamp with water. DO
NOT wipe with wet cloth and DO NOT
submerge in water. Always keep lamp
away from water.
•NOTE: Himalayan Salt Lamps may
“sweat” in humid conditions.
•How to Replace your Salt Lamp’s Bulb
•PRECAUTIONS:
•Always choose the correct bulb that is compatible with your
lamp’s socket AND cord. Make sure it is the correct size AND
wattage. This information can usually be found on the cord.
•DO NOT exceed manufacturer’s maximum wattage as specified
on the cord.
•When changing and replacing bulbs, always be careful of broken
glass.
•How to Replace the Bulb:
•1. Unplug the lamp and allow the bulb to cool. (If your lamp is a
basket-style lamp, remove the salt chunks and set them aside in
a safe, dry location.)
•2. Remove the cord: Squeeze the metal prongs and pull the bulb
socket straight out.
•3. Unscrew the bulb from the bottom of the socket.
•4. Screw in a new bulb carefully. The bulb should screw in
smoothly. DO NOT force it in. Ensure the bulb is secured tightly in
the socket.
•5. Reinsert the cord into the lamp. Ensure that it is fully inserted.
DO NOT force it in. Tuck in the cord securely to make sure the
lamp is balanced.