IOGear GUWAVKIT4 User manual

www.iogear.com
User Manual
Wireless 1080p Computer to HD Display Kit
GUWAVKIT4
PART NO. M1227-a

3
Table of Contents
Introduction 4
Package Contents 4
Requirements 4
Specications 5
Overview 6
Prepare to Software Installation - Windows 6
Software Installation - Windows 7
Hardware Installation 10
Using the IOGEAR Wireless Software - Windows 12
Troubleshooting and Support 21
Federal Communications Commission (FCC) Statement 26
Limited Warranty 27
Contact 27

4
Package Contents
Requirements
1 x Wireless A / V Receiver
1 x Wireless USB Transmitter
1 x Power Adapter
1 x User Manual
1 x Warranty/Registration Card
1 x Installation CD for PC
PC:
• Intel 2.2GHz processor (2.4GHz Recommended) with 2GB (3GB Recommended) of
system memory (RAM)
• Windows® XP (32-bit) SP3, Windows Vista® SP2, Windows® 7, Windows® 8
• Graphics Chipsets Supported: Intel, AMD, and nVIDIA
• An available USB 2.0 Port
TV:
• HDTV or Projector with HD, VGA (RGB / D-sub 15-pin / PC), or DVI port (DVI adapter not
included)
• TV or audio system with HD or 3.5mm audio jack
Introduction
The GUWAVKIT4 Wireless 1080p Computer to HD Display Kit allows users to watch and share
any notebook or PC content (such as pictures, movies and presentations) and any Internet
content on their HDTV, projector, or monitor without cable limitations and in up to stunning
1080p HD.
The GUWAVKIT4 transmitter connects to a USB 2.0 port available in the notebook PC and the
Receiver Base connects to either an HD port available in at screen TV or a VGA connection in
monitors & projectors. Stereo audio is supported via the HD port (along with the video) or via a
separate 3.5mm audio jack.
The GUWAVKIT4 provides full room coverage, is easy to set up and use, and is an ideal
solution for both home and ofce use. It delivers the best combination of performance and cost
in a variety of living room, conference room and classroom environments.

5
Specications
Base Receiver
• Video Out: HD Connector, VGA Connector
• Audio Output: 3.5mm Stereo Jack
• USB 2.0 port to support keyboard and external hard drives.
• Streaming video up to 1080p resolution
• Supports both Mirror Mode and Extended Mode (TV/monitor as a second screen)
• 48 kHz, 16-bit Stereo via audio jack or HD connector
• Whip Antenna
• 5VDC Power Adapter
• LED power and Tri-color signal strength indicators
PC Adapter
• USB Type-A male
• Internal transmission antenna
Standards
• Wireless USB 1.0, UWB certied
• Certied WiMedia PHY and MAC
General
• Same room, line of site range, up to 30ft
• 128-bit AES security
• Software drivers: Windows® XP (32-bit) SP3, Windows Vista® SP2, Windows® 7,
Windows® 8
• Input voltage: 100-240V, 50/60Hz
• Operating temperature range: 0-40 C

6
Overview
Prepare to Software Installation - Windows
Receiver Base Front View
1. Power / Signal
Indicator Light
2. Wireless Connection
LED Light
Receiver Base Back View
1. DC Power Input
2. HD Port
3. D-Sub 15Pin (VGA)
4. 3.5mm Audio Out
5. USB 2.0 Port
6. Antenna
PC Adapter
1. USB 2.0
If your PC contains a previous IOGEAR Wireless Software or other Wireless USB
driver installation, please perform a proper uninstall procedure using the Windows
Control Panel.
Prior to Software Installation:
1. It is important to make sure there is no prior installation of Wireless USB or Display Link
software from IOGEAR or other com¬panies. IF YOU HAVE THIS SOFTWARE IN YOUR
SYSTEM, THIS WILL CAUSE THE IOGEAR WIRELESS SOFTWARE NOT TO WORK
PROPERLY.
2. Go to Control Panel>Programs and Features and look through your programs to ensure
you do not see any UWB wireless programs.
3. If you see any UWB wireless programs listed under program name, uninstall it by
highlighting and clicking on the Uninstall tab.
4. The installation software requires .NET Framework version 2.0 (or later) to be installed on
the computer. In case it is not installed it may be downloaded from the following location:
http://www.microsoft.com/downloads/details.aspx?FamilyID=0856EACB-4362-4B0D-
8EDD-AAB15C5E04F5&displaylang=en
5. Anti Virus software set to very high security may prevent the installer from running. It is
recommended to temporarily disable the Anti viruses SW during the installation.
1 1 1 2 3 4 652

7
Software Installation - Windows
1. The installation checks the PC capabilities and compares them to the minimum system
requirements of the system. For Vista/Win7 it is recommended to run WEI (Windows
experience index) calculation prior to installation.
2. Ensure that the PC Adapter is unplugged from the PC.
Software Installation
1. Insert the installation CD in the PC CD-ROM drive
2. The installation CD License Agreement menu is displayed below.
3. Check the “I agree to the license terms and conditions” box and click on “Install”.
4. The software will automatically create a folder and load the software content into the
C: drive in the Program Files folder.
5. The software will automatically create a folder and load the software content into the
C: drive in the Program Files folder.

8
Uninstalling the Software (2) Methods:
Method 1
1. In the event you need to uninstall the software, insert the CD. Once the Modify Setup
screen appears, click on “Uninstall”. Note: The Modify Setup screen will only appear if the
IOGEAR wireless software is already installed on your PC.
2. An Operation Progress screen will appear during the Uninstall process.
3. Once the Uninstall process is completed, an “Operation Successful” screen will appear.
Click on “Restart” to restart your PC and complete the Uninstall process.
6. During software installation, the Operation Progress screen will appear.
7. Once Setup is completed, the Operations Successful screen will appear.
Click on “Restart” to restart your computer.

9
Repairing the Software:
1. In the event you need to repair the software, insert the CD. Once the Modify Setup screen
appears, click on and click on “Repair”. Note: The Modify Setup screen will only appear if
the IOGEAR wireless software is already installed on your PC.
2. An Operation Progress screen will appear during the Repair process.
3. Once the Repair process is completed, an “Operation Completed” screen will appear.
Click on “Restart” to restart your PC and complete the Repair process.
Method 2
1. Click on Windows Start button on your desktop and select Control Panel>Program and
Features. Uninstall the following program: GUWAVKIT4

10
3. Connecting a TV, Monitor or Projector
1. You can connect a digital (HD) or analog (VGA) monitor to the Receiver Base.
Note: Only one monitor can be connected to the HD Adapter at a time.
2. Connect an HD or VGA Cable to the HD or VGA port on the Receiver Base
3. Connect the other end of the cable to the TV, Projector or external monitor.
Hardware Installation
1. Connect the Wireless USB PC Adapter
1. Connect the Wireless USB PC Adapter to
a high speed PC USB port.
2. The system will automatically detect and
install the drivers.
2. Connect the Power Adapter
1. Plug the AC Adapter cord into the DC-IN
on the back of the Receiver Base.
2. Connect the AC adapter a live electrical
outlet. The power light on the front panel
glows red when the Receiver Base is
powered on.
Option 1 - HD
Option 2 - VGA

11
4. Connecting Audio Devices
1. The Wireless USB Device Adapter provides one 3.5mm port, as
shown in the illustration above.
5. Set-Up Complete
1. The default conguration for the external monitor connected to the Receiver Base is in
the Extend mode (an extension of the image on the computer to a second screen).
2. When the PC’s image is displayed on the display/monitor, the Wireless Connection LED
Light bar on the front panel will glow blue. The Power/Signal light will either glow green
(good signal), orange (fair signal) or red (weak signal) depending how far away the PC/PC
Adapter is from the Receiver Base. For best video image results, please position the PC/
PC Adapter close enough to the Receiver Base so that the Power/Signal Indicator Light
shows green.
Note: HD and 3.5mm options may be operated simultaneously
6. Connecting USB Devices* (Optional)
1. The Receiver Base provides one USB 2.0 port
2. Connection can be made to an External HDD’s, IOGEAR wireless keyboard etc.
*Webcam’s are not supported.
Notes: IOGEAR Wireless AV Multimedia
Keyboards with trackball make a perfect
companion: GKM561R, GKM681R,
GKM581R and GKM571R

12
A: Accessing the UWB Connection Manger
B: Accessing the UWB Connection Manger - To start the UWB Connection Manager:
Double-click the UWB Connection Manager icon in the System tray/Notication Area of your
Windows® desktop.
Note : The UWB Connection Manager icon appears as Green in your System tray/Notica¬tion
Area only when the USB Wireless PC adaptor is connected to your computer. You may need to
click the Show Hidden Icons button to display hidden icons. If the icon is not displayed in the
System Tray Notication Area, you can access the UWB Connection Manager by double click-
ing the UWB Connection Manager icon on your Windows® desktop.
Using the IOGEAR Wireless Software - Windows
This section provides information on using the following software to manage the
IOGEAR Wireless Software to adjust settings to suit your needs:
1. UWB Connection Manager
2. Adjusting Video Settings
3. Adjusting Audio Settings
You can also refer to this section to learn how to uninstall the software.
1. Introducing the UWB Connection Manager Software
The UWB Connection Manager is the driver software for your GUWAVKIT4. This driver is
automatically installed when you run the IOGEAR Wireless Software Installation CD. The
GUWAVKIT4’s USB Wireless PC Adapter contains a radio transmitter that enables your
computer to communicate wirelessly with the Receiver Base. This radio is known as the
host radio. The UWB Connection Manager driver software enables you to manage the host
radio and perform tasks such as the following:
• Connect/Disconnect the GUWAVKIT4 from your computer
• Change/Select the channel used for radio communication
• Disable/Enable radio communications
• Disable/Enable pop-up messages

13
C: The UWB Connection Manager display window will show the GUWAVKIT4(s) on the
Devices tab as Not Connected. Simply click on the Connect tab to establish a connection.
It will take approximately 15 seconds for the Drivers to load upon rst connection. When
the wireless connection has been made, a yellow star will automatically appear next to the
GUWAVKIT4 Icon, making it the default device for future connections. If the external monitor
connected to the Receiver Base shows only the wallpaper background of my Windows®
desktop, please refer to Page.15 to set the display mode to Mirror Mode.
D: Disconnecting the GUWAVKIT4 from your computer - On the Devices tab of the UWB
Connection Manager, right click on the connected GUWAVKIT4 and unselect “Set as Default”.
Once the device is no longer the default device, you can then either, a) double click on the
device, or, b) right-click and select “Disconnect”. The device will now move back to the “Not
Connected” status.
F: Renaming the GUWAVKIT4 - You can change the name of the each GUWAVKIT4 listed
on the Devices tab of the UWB Connection Manager. This is especially useful if you have
multiple GUWAVKIT4s to differentiate. To rename a GUWAVKIT4, right-click on the default
name, select Rename from the shortcut menu, and then enter a custom name.
tab of the Wireless USB Manager. This is especially useful if you have multiple IOGEAR-
GUWAVKIT4s, to differentiate between them. To rename an IOGEAR-GUWAVKIT4, right-click
on the default name, select Rename from the shortcut menu, and then enter a custom name.

14
G: Radio Communications Change/Select the channel used for radio communication -
The Communications tab of the UWB Connection Manager enables you to view and change
radio settings. The default channel setting is Automatic, which enables the host radio to
automatically locate an available channel for communications.
Note: It is recommended to leave this setting on Automatic. If you manually select a channel
that is being used by another GUWAVKIT4 in the vicinity, the channel bandwidth will be shared
by both devices. To maximize performance, there are eight channels to choose from and a
separate channel should be used for each GUWAVKIT4.
H: Disable/Enable Radio Communications - To temporarily disable the host radio, do the
following: Under the Communications tab, click the Off button in the Communication Status.
The radio is now in Airplane Mode and the UWB Connection Manager Icon in the System Tray
will now turn Orange:

15
2. Adjusting video settings
A. Selecting Extended mode or Mirror mode
You can choose to set the USB to VGA Adapter’s video output signal to Extend mode or
Mirror mode. The default setting is Extend mode.
Extend mode extends your desktop space across multiple monitors, so that you can
display different information on each monitor connected to your computer. This provides
a number of advantages to increase productivity, including the ability to:
• View large spreadsheets across two screens
• Multitask more effectively without overlapping windows
• Compare two documents simultaneously across two screens
• View videos/TV on one screen and reviews on the other
Mirror mode duplicates the image on your computer screen on the external monitor(s)
connected to USB to VGA Adapter. This mode is useful if, for example, you want to view
information on a larger, external desktop monitor instead of a smaller, built-in computer
screen. In Mirror mode, the Adapter automatically adjusts the external monitor’s resolu-
tion, color quality, and refresh rate settings to provide the best overall image quality
based on your computer’s settings.

16
B. Conguring the Display
1. Setting options for the display
The following are the suggested work congurations when connecting a display screen to
the Base Adapter:
• Mirror Mode
• Extend Mode
• Laptop with Lid Closed
• External Display Only
2. Conguring the Display in Windows XP/Vista
1) Using Viewspan icon in System tray/Notication Area
Advanced Settings Conguring the Display via Windows Display Properies in
Windows XP/Vista
Extend to Specify the extension direction if you are using multiple monitors
and Extended mode. This setting should match the physical
orientation of the connected monitors relative to each other. For
example, if the external monitor is physically positioned to the
right of your computer’s display, select “Extend to Right”.
Set as Entended Extend your desktop space across multiple monitors, so that
you can display different information on each monitor connected
to your computer.
Set as Mirror Duplicate the image showing on your computer’s screen on the
external monitor
Set Display Off Turn off the external display.

17
Adjusting Screen Resolution
Use the Resolution slider to adjust the desired resolution of the display
Adjusting Color Level (Color quality)
Use the Colors drop-down box to select a color complexity level)
Setting the Primary Display
Select the screen that is connected to the Base Adapter- for example 2.Default Monitor
as shown in the screen above
Check the option Extend my Windows desktop onto this monitor (in Windows Vista –
Extend the desktop onto this monitor”)
Check the options Use this device as the primary monitor (in Windows Vista-This is
my main monitor)
Click OK to save the new settings.
3. Conguring the Display in Windows 7
1) In windows 7, there is a built in support for external monitor. To use it press
the windows key together with the P key( + P), and then the following menu will
apper: 1) For Mirror mode: choose Duplicate and 2) For Extend mode: choose Extend
2) Using Windows Display Preperties on Windows XP/Vista
Setting the Display to Extend or Mirror Mode
• Mirror Mode : uncheck the option “Extend my Windows desktop on to this monitor”
• Extend Mode : check the option “Extend my Windows desktop on to this monitor”

18
2) Using Windows Display Properties on Windows 7
Click the Viewspan icon in the System tray/Notication Area
Click Change Display Settings
To congure screen resolution or any other display option, choose Advanced. The
following windows will appear.
To change any of the external display settings.
Select the appropriate display name in the Display scroll down options. You should select
the name of the TV or Monitor or Projector connected to your Receiver Base.
Select the desired value in any of the available settings
- Resolution: your external display resolution.
- Orientation: select either Landscape or Portrait.
- Multiple displays: select either Mirror or Extend mode.
Make this my main display: mark this option to make the external display the primary
display on which the desktop is displayed

19
3. Adjusting audio settings
A. Conguring audio ports
You can playback audio either through the Receiver Base’ audio port or the PC’s audio
port. However, you cannot use the audio ports on the Receiver Base and on the PC at
the same time.
By default, the audio ports on the GUWAVKIT4 are automatically enabled each time you
connect. When you disconnect the GUWAVKIT4 from the PC, the audio ports on the PC
are automatically re-enabled. To change the default settings, you may need to manually
adjust the audio settings in Windows®, as described in this section. For example, if you
want to use the PC’s audio ports while the PC is docked, you will need to change the
default settings.
To change the default settings, you may need to manually adjust the audio settings in
Windows®, as described in this section. For example, if you want to use the PC’s audio
ports while the PC is docked, you will need to change the default settings
B. Setting Audio Output Device
The PC audio output device should set itself automatically to the GUWAVKIT4’s
connected wireless audio device when the wireless connection is made to the Receiver
Base. If it does not switch automatically, it can be selected manually as follows:
In Windows XP:
• Right click the Volume icon in the System Tray and select Adjust Volume Properties.
• In the Sounds and Audio Devices Properties screen, select the Audio tab.
• In the Sound Playback > Default Device drop-down box, select the USB PnP
Sound Device.
• Click OK to save the new setting.

20
In Windows Vista/Win7:
• Right click the Volume icon in the System Tray and select Adjust Volume Properties.
• In the Sounds and Audio Devices Properties screen, select the Audio tab.
• In the Sound Playback > Default Device drop-down box, select the USB PnP
Sound Device.
• Click OK to save the new setting.
For all audio outputs (HD, 3.5mm):
• Click “Speakers USB PnP Sound Device” and click “Set Default”.