IPCamPower IPCP-EXT2P User manual

USER GUIDE
POE & Optical Transmission
POE Extender
Statement
Copyright © 2015 IPCamPower.com
Packing List
This document contains proprietary information that is protected by copyright. No part of this document
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language,
in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise
without the prior written permission of our company.
The information and product specifications within this document are subject to change at any time, without
notice and without obligation to notify any person of such change.
A POE extender
User Guide
Product introduction
Performance Characteristics
Product Feature
The IPCP-EXT2P PoE Extender allows for an incoming PoE powered signal to be extended to 1 or 2 PoE
powered devices. This takes down the barrier of a typical 100 meter distance restriction of PoE and can
extend it to even further distances. Furthermore, this extender is powered by the incoming PoE power
of your PoE switch or injector (not included), therefore you do not have to worry about having a nearby
power recptacle to power this device. Additionally, this device acts as a PoE powered 2 port
unmanaged switch as it has 1 input which accepts the PoE power and 2 outputs which extends the PoE
power to up to 2 PoE powered networkable devices such as IP cameras.
Complies with IEEE802.3, IEE802.3u , IEEE802.3ab, IEEE802.3af , IEEE802.3at standard
Plug and play, no need to set.
Data transmission speed rate : 10/100Mbps
PD mode (power pins ) can comply both with 1/2+,3,6- (End-span ) & 4/5+, 7/8- (Mid-span )
Excellent circuit isolation.
Mean Time Between Failures( MTBF ) : 30000h
Transmission signal channel surge protect 1KV standard : IEC61000-4-5
Small Footprint
Mechanical strcuture and Port description
A. PD Input Rj45 port B. POE extender working Status Light
C.PSE Output Rj45 por t D. POE woking Status Light
25mm
80mm
76mm
A B C
PSE2 OUT
PSE2 O UT PSE1 O UT
PSE1 OUT
D
E.Networt port working status
E

Product internal design description
Indicator Status Description
Remark: Please Confirm that the PD complies with IEEE802.3af/at standard
PoE Inidcators: Device has indicator lights showing if it is attached to a compatible PoE powered type of device.
PoE IN cable: Please use UTP Cat5 or above to connect with PSE or PD.
PoE OUT cable: Please use UTP Cat5 or above to connect with Ethernet device.
PD working normal
Incorrect PSE device connection
PD overload
PoE output normal
Not connected PD or Power supply type are not matched
Connected PD overload or undetected standard PD
ON
OFF
Blink
ON
OFF
Blink
PD RUN
PoE RUN
PoE splitter cable installation instruction
Installation guide
Please use the assorted equipments to install
Installation
PoE extender is used with power supply unit and PoE device, can used in the network environment
without the power supply cord or away from the power outlet , it can supply power for AP, IP camera ,
VoIP and other network devices.
Please link the PoE splitter correctly in the following steps:
Attention:
1).The Ethernet device connected with PoE extender shall not exceed maximum power of the PoE
extender.
2).Even if the supply of power is enough, the same communication connected with PoE extender
also must not exceed 3-level.
Confirm before installation:
1.Whether the power supply of PoE port is in line with the access equipment power demand or not.
2.Whether PoE standard requirement and power supply match with the PD of access (mid span/end
span) or not.
1).Using UTP Cat5 cable to connect PoE port access of the power supply device(such as PoE switch)
to PD IN port of this PoE extender.
2).Using UTP Cat5 cable to connect PoE OUT port of the PoE extender with PD.
Solution diagram
UPLINK
PoE Swi tch
PoE E xtende r
Data +Powe r
Wide Area Netw ork
100M
Data +Powe r
PoE W irele ss
PoE E xtende r
IPCP-EXT 2P
PoE I P Camera
PoE E xtende r
PoE I P Camera
100M D ata+Powe r
100M Da ta+Power
100M
Product model and parameter description
IPCP-EXT2P: 10/100Mbps PoE extender , its front-end is powered , and its back-end is PSE ,
IEEE802.3af,15.4W, extending 100m
Port Description : PD input R J45, PSE output RJ45
Network Media : 100BASE-TX: UTP Cat5 , 100m or less
Network Protocols: IEEE 802.3i; IEEE 802.3u; IEEE 802.3x Flow Control; IEEE 802.1af DTE Power via MDI
PoE port : PoE IN PD (25.5W) , PoE Out PSE (15.4W )
PoE Standard : IEEE802.3af (por t power : 15.4W), IEEE802.3at ( port power : 25.5W).
PoE Type : PoE front PD input support End-span & Mid-span , PSE port only support
End-span or Mid-span .
PoE Cable core: 1/2+, 3/6-
Electromagnetic Emission(EME) : CE mark, commercial , FCC part 15 Class B RoHS.
Product Size & Weight : 80mm*76mm*25mm(L*W*H), 0.15kg
Operating temperature : 0 to 55° C
Storage temperature : -20 to 70°C
Working humidity : 10%～90% (no condensation )
Storage humidity: 5% 90% (no condensation )
PoE-Ext ender
PSE2 OUT
PoE RUN
IN
OUT
PSE1 OUT
PD RUN
PD IN
IN
Power over Ethernet Extend er
PoE-Ext ender
PSE2 OUT
PoE RUN
IN
OUT
PSE1 OUT
PD RUN
PD IN
IN
Power over Ethernet Extend er
PoE-Ext ender
PSE2 OUT
PoE RUN
IN
OUT
PSE1 OUT
PD RUN
PD IN
IN
Power over Ethernet Extend er