Iper Ceramica TAORMINA VASCA User manual

Massage Bathtub Installation guide
TAORMINA VASCA
1700x700x630mm

21
3. Technical Specifications:
Model
Rated Voltage 230 V ~
Rated Frequency 50 Hz
Rated Power 750 W
IP Code IP25
4. Tools list(not include):
X1
D
5. Parts list
Product feature
1.PRECAUTION BEFORE INSTALLATION:
Save for future reference. Read this intallation manual carefully before
intallation.
Check all fittings according to the fittiong list. Prepare all parts and tools
needed and install bathtub following the installation procedure.
2. IMPORTANT SAFETY GUIDELINES:
This appliance is not intended for use by persons (including children) with
reduced physical,sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
– parts containing live parts, except parts supplied with safety extra-low voltage
not exceeding 12 V, must be inaccessible to a person in the bath;
earthed appliances must be permanently connected to fixed wiring;
parts incorporating electrical components, except remote control devices,
must be located or fixed so that they cannot fall into the bath;
– the appliance should be supplied through a residual current device
(RCD)having a rated residual operating current not exceeding 30 mA.41
–
–
Trim air
switch
Drainage
Nozzle
Massage switch
Backwater
TAORMINA VASCA

43
Step 1: Waterway installation.
Step 2: Keep bathtub horizontal by adjusting foot screw.
Step 3: Install pillow
Please select and prepare a right place for the bathtub installation
by well considering the bathtub dimension.
S
ø4
0mm
Foot screw
Levelling instrument
D
Step 4: Joint drain pipe into sewer.
Step 5: Inject silicon at juncture of bathtub and wall.

5CM
Remark:If you want to start the bathtub the water level must
exceed nozzle by 5 CM.
65
Overflow
1.Using Methods
a.First open the function switch and choice the waterfall function.
b.Second open the cold water control switch then open the hot water antrol switch
and adjust the water temperature.
c.Start the massage switch when the water level exceed nozzle by 5 CM.
d.If you need you can adjust the trim air switch.
e.When you finished ,please turn off the massage switch.
2.Clean&Maintenance
a.Can use neutral liquid detergent and soft cloth to clean surfing bathtub,
detergent containing acetone and
ammonia are prohibited to use;While disinfecting forbid to use
disinfectant containing formic acid and formaldehyde.
b.If there are scrapes on the surface of bathtub,only polish it with
2000# waterproof abrasive paper and coat toothpaste
then polish them with soft cloth.
c.Because the water scale can be cleaned by acid detergent such as
citric acid and vinegar, you can clean it with soft cloth.
d.If there is hair on backwater hole and nozzle,please clean them at once.
e.Chromate-plating surface needn’t wipe frequently.
f.Tool with rough surface, detergent containing chemical solvent are forbidden
to use .
g.Neither knock the surface of bathtub with hard tool or knife nor let dog-end
and heat source above 100℃touch the surface of bathtub.
h.Clean hydraulic massage equipment:Fill in 40℃ hot water and add in detergent
according to proportion of 2 g/L. Start hydraulic massage for about five minutes
and drain water out,then fill in cold water and start hydraulic massage for about
threeminutes and drain water out to clean bathtub.
Recycling (Disposal of the product at the end of its life):
Waste Electrical Products Should Not Be Disposed Of With Household
Waste. Please Recycle Where Facilities Exist. Check With Your Local
Authority For Recycling Advice.
3.Trouble Shootings
For any trouble with the product, please ask senior repairman to perform
maintenance.