iProSecu iDC-953MIR User manual

1/42
User Manual
IR IP Camera

2/42
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION：TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED
TO THEIR RESPECTIVE COMPANIES.

3/42
Content
I. PREFACE....................................................................................................................................... 4
II. PRODUCT SPECIFICATIONS ....................................................................................................... 4
III. PRODUCT INSTALLATION ........................................................................................................... 7
A. M ONITOR S ETTING ..................................................................................................................................... 7
B. H ARDWARE I NSTALLATION AND I/O P IN A SSIGNMENT ............................................................................... 8
C. IP A SSIGNMENT ....................................................................................................................................... 11
D. I NSTALL A CTIVE X CONTROL :................................................................................................................... 13
IV. LIVE VIDEO.................................................................................................................................. 15
V. SYSTEM CONFIGURATION........................................................................................................ 18
A. S YSTEM .................................................................................................................................................... 19
B. N ETWORK ................................................................................................................................................ 22
C. A/V S ETTING ........................................................................................................................................... 29
D. E VENT L IST .............................................................................................................................................. 36
VI. NETWORK CONFIGURATION .................................................................................................... 40
VII. FACTORY DEFAULT.................................................................................................................... 42
VIII. PACKAGE CONTENTS ............................................................................................................... 42
APPENDIX I .......................................................................................................................................... 42
V1.1_110905

4/42
I. Preface
IR IP CAMERA is a professional CCD IP camera. It has built-in web server which
enables user to view real-time video via IE browser. It also supports
simultaneously H.264, MPEG-4&JPEG video compression and dual streaming
which provides smooth and high video quality. The video can be stored in the SD
card, and can be playback remotely.
IR IP CAMERA is an easy-to-use IP Camera which is designed for security
application.
II.Product Specifications
Video Out
High Definition Resolution at 30FPS support(720P)
IP66
External Vari-focal lens adjustment
True Day/Night Function
Mechanism IR Cut Filter Available
Fan Built-in
IR Distance: 40/30 Meter
H.264/ JPEG/ MPEG4 compression
Support Cell Phone/PDA/3GPP
Triple streaming
SDK for Software Integration
Free Bundle 36 ch recording software
Specifications
Hardware
CPU ARM 9 ,32 bit RISC
Memory 256MB
Flash 16MB
Sensor 1/3” CMOS(2M-Pixel)
Sensitivity 0 Lux(IR on)

5/42
Lens 30M/40M: Vari-Focal Auto Iris 3.6~16mm
Fan Always On
ICR Yes
LED
56 Unit 5φ850nM infrared LED, 10000hrs
(40M)
42 Unit 5φ850nM infrared LED, 10000hrs
(30M)
IR DISTANCE 40M/30M
I/O 1 in/ 1out(Relay Out)
Video Out 1
Power Consumption DC 12V
Water Resistance IP66
Dimensions 114mm(ψ) x 260mm(D) (With Shield)
99.4mm(ψ) x 225mm(D) (Without Shield)
Network
Ethernet 10/ 100 Base-T
Network Protocol HTTP, UDP,TCP/ IP, SMTP, FTP, PPPoE,
DHCP, DDNS, NTP
Wireless (Optional)
Wireless 802.11b/g
Security WEP,WPA-PSK,WPA2-PSK
System
Video Resolution 1600x1200, 1280x1024, 1280x960,1280x720,
800x600,640x480, 320x240, 176x144
Video adjust Brightness, Contrast, Sharpness,BLC,Night
Mode
Triple Streaming Yes
Image snapshot Yes
Full screen monitoring Yes
Privacy Mask Yes
Compression format H.264/JPEG/MPEG4(3GPP only)
Video bitrate adjust CBR, VBR
Motion Detection Yes, 3 different areas
Triggered action Mail, FTP, Relay
Pre/ Post alarm Yes, configurable
Security Password protection

6/42
Firmware upgrade HTTP mode, can be upgraded remotely
Simultaneous connection
Up to 10
Web browsing requirement
OS Windows 2000, XP, 2003, Microsoft IE 6.0 or
above
Hardware
Suggested
Intel Dual Core 1.66G,RAM: 1024MB, Graphic
card: 128MB
Minimum Intel-C 1.6G, RAM: 256MB, Graphic card: 32MB
*SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

7/42
III. Product Installation
A. Monitor Setting
i. Right-Click on the desktop. Select “ Properties”
ii. Change color quality to highest (32bit).

8/42
B. Hardware Installation and I/O Pin
Assignment
i. Connect a power adapter and IP Camera to PC or local network
ii. I/O Control Instruction
I/O terminal connector – used in application, for e.g., motion detection, event
triggering, alarm notifications. It provides the interface to:
1 Digital Input (GND+Alarm) – An alarm input for connecting devices that can
toggle between an open and closed circuit, for example: PIRs, door/window
contacts, glass break detectors, etc. When a signal is received the state changes
and the input becomes active.
Relay output (COM +N.O.) / (COM+N.C.) – An output to Relay switch, for
example: LEDs, Sirens, etc
iii. Digital Input
Alarm Input
1. GND (Ground) : Initial state is LOW
2. Alarm : Max. 50mA, DC 3.3V
Relay Output
1. N.C. (Normally Close): Max. 1A, 24VDC or 0.5A, 125VAC
2. COM: (Common)
3.5mm Phone Jack (Audio Input, Red)
3.5mm Phone Jack (Audio
Out
put,
Green
)

9/42
3. N.O. (Normally Open): Max. 1A, 24VDC or 0.5A, 125VAC
Relay
1. Digital Input connection
GND
ALARM
N.C.
COM
N.O.
Door/Window
Contacts
ALARM IN
RELAY OUT

10/42
2. Relay Output Connection
Or
GND
ALARM
N.C.
COM
N.O.
GND
ALARM
N.C.
COM
N.O.

11/42
C. IP Assignment
i. Use the software, “IP Installer” to assign the IP address of IP CAMERA.
The software is in the attached software CD.
ii. IP installer supports two languages
a. IPInstallerCht.exe：Chinese version
b. IPInstallerEng.exe：English version
iii. There are 3 kinds of IP configuration.
a. Fixed IP (Public IP or Virtual IP)
b. DHCP (Dynamic IP)
c. Dial-up (PPPoE)
iv. Execute IP Installer
v. For Windows XP SP2 user, it may popup the following message box.
Please click “Unblock”.
vi. IP Installer configuration:
vii. IP Installer will search all IP Cameras connected on Lan. The user can
click “Search Device” to search again.

12/42
viii. Click one of the IP Camera listed on the left side. The network
configuration of this IP camera will show on the right side. You may
change the “name” of the IP Camera to your preference (eg: Office,
warehouse). Change the parameter and click “Submit” then click “OK”. It
will apply the change and reboot the Device.
ix. Please make sure the subnet of PC IP address and IP CAM IP address
are the same.
The same Subnet:
IP CAM IP address: 192.168.1.200
PC IP address: 192.168.1.100
Different Subnets:
IP CAM IP address: 192.168.2.200
PC IP address: 192.168.1.100
To Change PC IP address:
Control PanelNetwork ConnectionsLocal Area Connection
PropertiesInternet Protocol (TCP/IP) Properties
Please make sure your IP Camera and PC have the same Subnet. If not,
please change IP Camera subnet or PC IP subnet accordingly.
x. A quick way to access remote monitoring is to left-click the mouse twice
on a selected IP Camera listed on “Device list” of IP Installer. An IE
browser will be opened.

13/42
xi. Then, please key in the default “user name: admin” and “password:
admin”.
D. Install ActiveX control:
For the first time to view the camera video via IE, it will ask you to install the
ActiveX component.
If the installation failed, please check the security setting for the IE browser.
i. IE Tools Internet Options… Security Tab Custom Level… 
Security Settings Download unsigned ActiveX controlsSelect
“Enable” or Prompt.
ii. IE Tools Internet Options… Security Tab Custom Level…
Initialize and script ActiveX controls not marked as safe Select
“Enable” or Prompt.

14/42
1 2
3 4
5
When popup the following dialogue box, click “Yes”.

15/42
IV. Live Video
Start a IE browser, type the IP address of the IP camera in the address field. It will
show the following dialogue box. Key-in the user name and password. The default
user name and password are “admin” and “admin”.
When connect to the IP CAMERA。The following program interface shows.
Right-Click the mouse on the video, it will show a pop-up menu.
2
3
4
5
6
1
7
8
9
10
11

16/42
1. Real-Time Display panel shows live streaming of video information
remotely.
2. Snapshot an Evidence of important event in still JPEG format.
3. Recording as AVI files continuously. For details, see next section.
4. Digital Zoom for bringing up an area of interest closely. For details, see
next section.
5. Playback SD Archives of important events captured and stored in local
SD Card medium.
6. System Configuration
for user accounts, system, network, video, audio,
events, etc.
7. Status Bar shows system time, video resolution, a
nd current video frame
rate.
8. Dual Streaming Channel enables secondary viewing device (such as
mobile or PDA phones) to receive real-time streaming at
lower-yet-appropriate frame rate per second. This feature is available
only if Streaming 2 is being enabled in Video setting.
9. Bi-directional Audio Communication enables full-duplex voice
communication between local and remote surveillance sites. To speak,
click on [Communication] box. To listen, enable Incoming Audio in
Audio setting.
10.
Online Visitor
shows num
ber of users are currently accessing this IP

17/42
Double-click the video, it will change to full screen mode. Press “Esc” or double-click
the video again, it will change back to normal mode.
Right-Click the mouse on the video, it will show a pop-up menu.
1. Snapshot：Save a JPEG picture
2. Record Start：Record the video in the local PC. It will ask you where to save the
video. To stop recording, right-click the mouse again. Select “Record Stop”. The
video format is AVI. Use Microsoft Media Player to play the recorded file.
3. Mute：Turn of the audio. Click again to turn on it.
4. Full Screen：Full-screen mode.
5. ZOOM: Enable zoom-in and zoom-out functions. Select “Enable digital zoom”
option first within the pop-up dialogue box and then drag and drop the bar to
adjust the zoom factors.

18/42
V. System Configuration
Click to get into the administration page. Click to go back to the live
video page.

19/42
A.System
i、System Information
a. Server Information: Set up the camera name, select language, and
set up the camera time.
1. Server Name：This is the Camera name. This name will show
on the IP Installer.
2. Select language：There are English, Traditional Chinese, and
Simplified Chinese to select. When change, it will show the
following dialogue box for the confirmation of changing
language.
b. OSD Setting: Select a position where date & time stamp / text
showing on screen.
Moreover, click Text Edit can entry to adjust the OSD contents
which is including Size and Alpha of text. Finally, click Upgrade
button to reserve the setting.
c. Server time setting：Select options to set up time - “NTP”,
“Synchronize with PC’s time”, “Manual”, “The date and time remain

20/42
the same”.
ii、User Management
IP CAMERA supports three different users, administrator, general user,
and anonymous user.
a. Anonymous User Login：
Yes：Allow anonymous login
No：Need user name & password to access this IP camera
b. Add user：
Type the user name and password, then click “Add/Set”.
c. Click “edit” or “delete” to modify the user.