Iris Innovations IM-DCS-01 User manual

IM-DCS-01

USER
GUIDE

IM-DCS-01 SERIES DUAL CAMERA HOUSING
Dual Module Marine Docking Camera Unit
Dimensions 134 (W) x 82 ( ) x 53 (D)mm
Weight 400g
Material Aluminium ard Anodysed / White Powder Coat Finish
Imaging 1/3” SONY CCD
Horizontal Resoluiton 420 TVL Low Illumination
Pixels PAL: 795( ) x 596(V) NTSC: 811( ) x 508(V)
TV System PAL / NTSC
Scanning PAL:625 Lines, 50 Field/Sec; NTSC:525 Lines, 60 Field/Sec
White Balance Automatic
Synchronization Internal
Output Signal 2 x Composite Video 1V P~P 75Ω
Usa le Illumination 0.8 Lux / F1.2
Shutter Speed Auto:PAL 1/50~1/100,000 Sec ; NTSC 1/60 ~1/100,000 Sec
IR Status N/A
Connections Video via 2 x BNC Female / Power via DC Jack 2.1mm
Lens 3.6mm Fixed (other options available upon request)
Illumination IR Version available soon!
Power DC12V 120 mA (60mA per camera module)
Operating Temperature -10°C ~ +50° Relative umidity 95% Max
Environmental Rating IP66
Signal / Noise 48db or more (AGC OFF)
Gamma 0.45
CAUTION
ELECTRIC SHOCK RISK. DO NOT OPEN
TO REDUCE T E RISK OF ELECTRIC S OCK DO NOT REMOVE COVER
OR DISMANTLE DEVICE. NO USER SERVICEABLE PARTS INSIDE. IN T E
EVENT OF MALFUNCTION OR PRODUCT FAILURE CONTACT YOUR
DEALER.
DO NOT ATTEMPT TO CONNECT TO ANY POWER SUPPLY OUTSIDE OF
T E RATING SPECIFIED IN T E SPECIFICATION TABLE OR GUIDELINES
DETAIL WIT IN T IS DOCUMENT.
WARNING: READ BEFORE USE

INTRODUCTION
Dual Module Marine Docking Camera Unit
CONNECTIONS
The IM-DCS-01 Dual Module Water Resistant Camera adopts the latest SONY tech-
nology, CCD Sensor and driver.
Key features of the DCS-01 are itʼs attractive, stylish housing, environmental protection
(IP66 - Itʼs water resistant but donʼt submerge!), ease of installation and setup and high
resolution.
Each housing includes 2 camera modules mounted on fully adjustable brackets that
allow the user to obtain near 180 degree coverage.
The IM-DCS-01 is perfect for use as a docking camera, and can either be used as a
pair of housings (4 cameras) looking forward and aft, port and starboard, or mounted
sideways with each camera module focused on the port and starboard aft quarters.
Please ensure installation is carried out by qualified engineer and that the device is
properly connected to the power source. This equipment must be suitably isolated to
prevent damage or risk of injury. For further technical support please contact your
dealer, or Iris Innovations using the contact details within this document.
The DCS-01 camera is fitted with a cable tail which has a 2.1mm DC Jack for the
power and two female BNC connector for the video signal. The polarity of the power
connection is center pin = +12V, connector body = Ground.
Use a suitable coaxial cable with an impedance of 75Ω for the video signal or a suit-
able Video Balum if using Cat 5 cable.
Ready made power, video and combination cables are available from Iris Innovations.
Video (1v P~P Composite 75Ω)
2 Inputs
12VDC 300mA
Connect to boatʼs distri-
bution panel and ensure
suitable isolation is in
place.
Chart Plotter / Dedicated Monitor /
DVR or Video Switching Equipment.

INSTALLATION & ADJUSTMENT
Electrical and electronic equipment, batteries, battery chargers and
equipment housings, at the end of their life should be disposed of sepa-
rately from your household waste. Please dispose of all components
correctly at your local waste collection / recycling centre.
Declaration of Conformity
Model Number: IM-DCS-01
Trade Name: Iris Marine
Responsible party: Iris Innovations Limited
Address: Sailmakers Loft, Kingscopse Farm, Tanhouse
Lane, Botley, Southampton SO30 2SZ. United Kingdom.
Telephone: [phone]
This device complies with Part 15 of the FCC Rules. Op-
eration is subject to the following rules:
(1) this device may cause harmful interference, and
(2) this device must accept any interference received, in-
cluding interference that may cause undesired operation.
Before using your camera please read and understand these
safety instructions.
Warning:
This product contains chemicals known to the state of California to cause cancer,
birth defects or other reproductive harm. Wash hands after handling.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions may cause harmful in-
terference to radio communications. If this equipment does cause interference to
radio or television reception the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorientate or relocate the receiving antenna.
Increase the separation between the equipment and transmitting / receiving de-
vice.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult your dealer or a qualified CCTV engineer for help.
Iris Innovations Limited
Unit 9 Swanwick Business Park.
Bridge Road, Swanwick, ampshire SO31 7GB
United Kingdom
Tel/Fax: [phone]
email: [email protected]
web: www.boat-cameras.om
1. Site camera appropriately, ensuring yourdrill
holes will not foul any other cabling or equipment.
Before making any permanent fixings it is advised
that the camera is offered into position, powered
up and the camera modules are adjusted to
acheive the desired views
2. When the housing position has been ascer-
tained mark the four fixing holes and central cable
hole through the base unit.
3. If drilling through gel coat, take care not to splin-
ter when drilling. Drill a pilot hole then very care-
fully drill out the 4 fixing holes in accordance with
your fixings. Use a 6mm drill for the cable entry
hole.
4. Carefully screw camera base to surface taking
care not to crack the gel coat as the screws are
tightened.
5. Adjust camera modules by loosening the brack-
ets with a 2mm hex key. Position the modules are
desired, checking the image on your screen then
fully tighten the hex screws to lock modules in
place.
6. Replace lens cover and top cover. It is recom-
mended that a bead of silicone grease be applied
to the top of the gasket that runs around the cam-
era base. Screw down tightly with 6 x M3 x 6mm
hex screws supplied.
7. Connect camera video and 12vdc power to the
camera cable tail.