Iris Ohyama SCD-181P User manual

Black SCD-181P
品名：824426㊥ＢＳ向取説ＳＣＤ１８１ＰＢ
サイズ：210×297（A4） 20ページ
材質：上質紙 菊判48.5kg（81.4g ／㎡）
刷色：1C（Black）
Indoor / Household Use Only
Contents
Preparations before use
Safety precautions..................................................2
Using precautions...................................................4
Parts .......................................................................5
How to use
Preparation.............................................................7
How to use..............................................................9
Cleaning and maintainance..................................12
How to replace the battery....................................16
Other
Troubleshooting....................................................17
Specications .......................................................18
Warranty and After-sales Service .........................19
Warranty card ......................................... Back cover
Rechargeable cyclone vacuum cleaner
SCD-181P
User manual

Black SCD-181P
2
Safety precautions
Read and follow this “Safety Precautions” carefully to ensure proper use of the product. These precautions are safety
precautions you must observe to prevent any injury and damage to property.
Danger The symbol means matters which may lead to death or serious injury
during faulty operation. Indicates content that is imminent.
●In
case of abnormalities or
malfunctioning, you should immediately
stop using and unplug the charger
adapter from the power socket
Or it may result in smoke, re or electrical shock.
〔Examples of Abnormalities〕
• Abnormal sounds or smell
• A bnormal heating up of the charger adapter
➡
S top using immediately and contact the retail
shop where you purchased the product.
Important notes about the battery
●Follow the instructions when
replacing the battery properly
Failure to use the machine correctly may
lead to battery damage and leaking or
cause re, injury, or environmental damage.
●If you get electrolysis solution
accidentally in your eyes,
immediately wash your eyes with
fresh water
It may hurt your eyes.
After washing your eyes, immediately seek
medical treatment.
●Do not disassemble the battery.
Or it may cause the battery to heat up and
rupture, causing a re or injury.
Warning The symbol means matters which may lead to death or serious
injury during faulty operation.
●D
o not spray on the product (such as
insecticide, hair dressing or grease)
●D
o not let the product inhale ammable
substances (kerosene, gasoline,
thinner, photocopier toner, etc.)
●Do not let the product inhale oily
smoke and steam
●D
o not let the product inhale foamy or
liquid substances such as blanket cleaners
●Keep away from sources which
could cause combustion or ame,
such as cigarettes, incense, etc
Inhaling them may result in a re.
●Do not use the product in the rain or
near water sources, bathrooms or
other places with high humidity
●Do not put the main body or the
charger adapter in water, or get
water on them
It may cause re or electric shock.
This symbol means
“reminding”.
This symbol means
“forbidden”.
This symbol means necessary
“instructions”.
Examples of symbols
●Do not use other than the dedicated/
recommended batteries
●Do not charge the battery in a way
other than what is specied
●Do not use with any devices other
than those designated
●Do not charge the battery in
locations with high temperatures or
exposure to direct sunlight
●Do not throw the battery into re or
otherwise heat it up in any way
●D
o not drop the battery from high
places, throw the battery, pierce the
battery with nails, strike the battery
with a hammer, or trample the battery
●Keep the battery from getting wet
Or it may cause the battery to heat up, rupture,
and leak uid, which may cause re, injury, or
contamination of the surrounding environment.

Black SCD-181P
3
Important notes about the battery
●In
the event of electrolyte leakage or
unpleasant odors, immediately distance
the product from all sources of re
Or it may cause a re.
●If electrolytes accidentally come
into contact with skin or clothing,
immediately wash with water
Or it may cause skin irritation or damage to clothing.
●In the event of electrolyte leakage or
unpleasant odors, do not use
Or it may cause overheating, re, or con-
tamination of the surrounding environment.
●Keep the battery out of the reach of
infants and young children
Or it may cause electrical shock or injury.
Use the charger adapter properly.
●R
emove dust from the power plug regularly
Dust buildup may lead insulation failures due
to moisture, cause re or electric shock.
●D
o not use unless the charger
adapter plug has been rmly inserted
all the way into the power socket
Doing so may cause re or electric shock
due to short circuiting.
●Do not plug or unplug the charger
adapter with wet hands
Doing so may result in electrical shock,
burns or injury.
●Do not use if the charger adapter
is damaged or does not plug rmly
into the power socket
Doing so may cause re or electric shock
due to short circuiting.
●The product can only be powered
by AC100-240V currents
It may cause re or electric shock.
●Do not allow infants or young
children to lick the charger adapter
Or it may cause injury or electrical shock.
●Do not touch the brushroll on the
suction head
Doing so could pull you in and cause an
injury. This cleaner should especially not be
used where there are small children nearby.
Brushroll
●Do not disassemble, repair or
modify the product by yourself
Doing so may result in a re, electric shock or injury.
For repairs, please consult with the store
where you purchased the product.
Attention Indicates content where incorrect use could
cause bodily harm and damage to property.
●Do not use for any purpose other
than cleaning
Or it may cause malfunctioning or a re.
●Please do not use the product for
commercial purposes or anything
other than for household use
This product was designed for household use.
If the product is used for commercial purposes or any-
thing other than for household use, it may cause re.
●Do not remove the dust cup during
use
Or it may cause an accident.
●Do not continue using if the air
intake is clogged
●Do not cover the exhaust outlet
Or it may overheat and cause a re.
●Keep the product away from the re
or heater
Air from the air outlet could fan the ames on the
heater and make them bigger, causing a re.

Black SCD-181P
4
Safety precautions Continued
Using precautions
●When unplugging the charger
adapter, grasp and pull it by the
plug, not by the cord
Pulling it by the cord could damage the
cord and cause a re or electrocution.
●Unplug the charger adapter from the
power socket after each use
It may cause re or electric shock.
●D
o not sit on or lean against the product
●D
o not use in close proximity of children
●D
o not let children play with this product
Or it may cause injury.
●The product is utilized indoors only
Otherwise it will cause re or short circuit
due to the malfunction.
About consumables and products sold separately
●Batteries and lter sets may be purchased from the store where you purchased this product.
Battery
(Sold separately)
CBL10820
Filter set
(Exhaust lter and Sponge lter) (Sold separately)
(Sold separately) CFTS72
●This product is not an anti-magnetic design. Do not put watches, magnetic cards (credit cards), or other
items that are susceptible to magnets near the product.
●Do not expose the product to the following items. Doing so may clog the lter or cause a malfunction.
●Clean the dirt in the Dust cup before it exceeds the When dust is full.
• Water, liquid, damp trash, etc.
• A large amount of powder
• (re extinguisher)
• S harp metal such as needles, pins,
and other sharp objects, glass, etc.
• A large amount of sand, gravel, etc.
• Items stained with pet excrements
• A lot of trash
• Large pieces of trash
• Plastic bags, stockings, or other
items that can easily clog the
unit
Disposal
●To dispose this product, remove the battery and dispose it according to your local regulations.
Used batteries
●Remove the used battery and bring it to a battery recycling location. Do not treat the used battery as regular
household trash.
●Tape the two ends of the removed battery for insulation.

Black SCD-181P
5
Parts
Extension pipe
Pipe release button
Air vent
Main unit
Bottom of brush nozzle Brushroll
Suction head
release button
Charging port
Dust cup
Exhaust lter
Sponge lter
Cyclone unit
(top)
Mesh lter
Cyclone unit
(bottom)
Cleaning brush
Dust cup case
Non-slip rubber
Battery cover
Dust collection
limit
Dust cup release
button
Suction head
Dust cup
Handle
Control panel

Black SCD-181P
6
Attached to the back of the
dust cup case.
Parts Continued
■Accessories
■Operation panel
Charger adapter
Charging cord
Brush rotation button
Charging plug
Standard/Turbo mode button
O󰀨 (Stop) button
Front side
It can be used as a brush nozzle
when turning the suction head on
its side.
Battery indicator lights
Cleaning brush
Nozzle for gaps

Black SCD-181P
7
Preparation
■How to assemble the
vacuum cleaner
Depending on the intended use, the suction head or other
attachment can be attached to the main unit or to the extension pipe.
When using as a stick vacuum cleaner
①Insert the extension pipe into the main unit.
②Insert the suction head into the extension pipe.
②
①
Insert until you
hear it click
into place.
Insert until you
hear it click
into place.
Main unit
Suction head
Extension pipe
Non-slip rubber
※
After assembling, lie the cleaner down on its side
so it will not fall over.
Continued →
When using as a handheld vacuum cleaner
• Insert the suction head or another attachment
directly into the main unit.
Suction head
Main unit
Insert until you
hear it click
into place.
※
After assembling, lie the vacuum cleaner down on
its side so it will not fall over.
How to remove the extension pipe and
suction head
• To remove the suction head, pull it out while
pressing the suction head release button.
• To remove the extension pipe, pull it out while
pressing the pipe release button.
Pipe release button
Suction head
release button

Black SCD-181P
8
■Charging the battery
●After
purchasing this product, the battery must be
charged. Be sure to charge the battery before use. It
takes about 4 hours for the battery to become fully
charged.
• Insert the plug on the charger adapter into the
charging port on the main unit, and then plug the
charger adapter into the power socket.
Charging port
Charging plug
Charger adapter
• The battery indicator light will light up red, and the
battery will begin charging.
Indicator light comes on
Battery
• The battery indicator will go out once the battery is
fully charged.
Indicator light goes out
Battery
About the battery
●It is normal for the battery and charger adapter to
heat up while the battery is charging.
●The charging time and usage time vary depending
on the temperature and on the usage state of the
battery.
●Charge the battery at a room temperature between
5°C and 35°C . The battery will not charge normally
in places with lower room temperatures, or in
place with higher temperature and exposure to
direct sunlight. This could cause the battery to
last for a shorter timer, or to need more time to
become fully charged.
●When left uncharged for long periods of time (10
days or longer), be sure to charge the battery
before using it again.
Preparation Continued
■About the remaining
battery power
• The battery indicator light will ash when the
remaining battery power is low.
Flashes
Battery
Battery indicator light Remaining battery
power
Flashes slowly Remaining battery
power low
Goes out after ashing
slowly
No remaining battery
power
• If the battery indicator light is ashing, recharge the
battery.

Black SCD-181P
9
How to use
1
Press the button to select the mode of
operation
Standard/Turbo mode
• Press the standard/turbo mode button to begin
running the product in standard mode. press the
standard/turbo mode button again to run the product
in turbo mode instead.
• Whenever the standard/turbo mode button is
pressed, the product will switch between standard
and turbo modes.
2
Clean
• Suck dirt by slowly moving the suction head
forward and backward.
• When cleaning the tatami, move the suction head
along the tatami grid.
Continued →
3
When you have nished cleaning, press
the OFF button
• To turn o󰀨.
Brush rotation
• Press the brush rotation button to turn brush
rotation on or o󰀨.

Black SCD-181P
10
How to use Continued
■Disposing of debris
Attention
●Make sure to turn o󰀨 the power
before disposing of debris.
●Do not remove the dust cup with
the power still turned on.
●Do not let debris accumulate
past the marked dust
collection limit.
●Dispose of debris every
time you vacuum.
4
Remove the dust cup from the main unit
Press the release button on the base of the dust cup
to release the lock
（①）, and pull the dust cup to
ward yourself to remove it
（②）.
※
Forcefully removing without pressing the release
buttons may break the dust cup.
①②
Dust cup
release button
■U
sing as a handheld vacuum
cleaner
To use as a handheld vacuum cleaner, remove the
extension pipe.
※
Image of attaching the accessory nozzle for gaps.
The vacuum cleaner can be
used with the accessory nozzle
for gaps attached. The tip of this
nozzle can be rotated and used
as a brush nozzle.

Black SCD-181P
11
5
Dispose debris
• Pull the cyclone unit up, remove it, and discard any
debris.
※
Make sure to open the cup above the trash can to
prevent debris from scattering.
Cyclone unit
• After disposing of debris, attach the cyclone unit.
※
Align the protruding part of the cyclone unit with the
notch on the dust cup case, and attach it rmly as
far as it will go.
6
Attach the dust cup to the main unit
① Insert the tabs on the main unit of the vacuum
cleaner into the holes on top of the dust cup.
Tab
Hole
②Push the dust cup in until it clicks into place.
Click
※
Push the dust cup rmly into place.

Black SCD-181P
12
Cleaning and maintainance
Attention
●Turn o󰀨 the vacuum cleaner and
unplug the charger before cleaning.
●Do not get any water on the main
unit or the charger adapter. Doing
so could result in electrocution,
injury, or malfunctioning.
●Do not clean with any detergents, thinners,
benzine, bleaching agents, etc.
●Do not clean with any chemically treated cloths.
Main unit/extension pipe/outside of the
suction head/nozzle for gaps
Once a week
• Soak a soft cloth in cool or warm water (no warmer
than 40℃), wring out the wet cloth thoroughly and
wipe o󰀨 any stains.
• To remove stubborn stains, use a soft cloth soaked in
water to wipe o󰀨 the stains, and then use a dry cloth
to wipe o󰀨 the detergent.
Extension pipe
Suction head
Nozzle for gaps
Main unit
Main unit ventilation ue, extension
pipe, suction head
If clogged by dirt
• If the suction port on the suction head gets clogged
with dirt, use tweezers to remove the dirt.
Brushroll
• If the ventilation ue inside the main unit, the extension
pipe, or the inside of the suction head get clogged with
debris, it will reduce the suction power.
Inspect periodically, and if anything has become clogged
with debris, use tweezers or disposable chopsticks to
remove the debris.
Extension pipe

Black SCD-181P
13
5
Attach the brushroll
①Insert the side of the brushroll that does not have
gears rmly into the belt and into the axis of rotation
on the opposite side.
② Put the belt on the gears.
③ Fit the brushroll into place.
①
②
③
Attach belt
6
Attach the brush cover
① Hook the tabs on the brush cover into the inside of
the front end of the suction head.
②
While holding down the brush cover, use a coin to turn
the lock screw toward the direction of the lock（ ）.
① ②
Brushroll
If dirt is noticeable/if rotation stops from time to time.
1
Remove the brush cover
• Use a coin to unscrew the lock screw from the
brush cover turn in the direction of the
（ ）
and
remove the brush cover.
Brush cover
2
Remove the brushroll
①Hold up the side of the brushroll with the belt to
remove the belt.
② Pull the brushroll to the belt side, and remove it from
the axis of rotation on the opposite side.
① ②
Remove belt
3
Remove debris from the brushroll
• Use scissors or tweezers to remove any debris that
gets caught in the brushroll.
4
Wash the brushroll with water
※
If any debris get tangled up in the brushroll,
remove it with scissors or tweezers before washing
the brushroll.
• Dry o󰀨 thoroughly after washing
Continued →

Black SCD-181P
14
Dust cup Once every two months
1
Remove the dust cup from the main unit
• Press the dust cup release button
（①），
and pull
the dust cup toward yourself to remove it
（②）.
※
Forcefully removing without pressing the release
buttons may break the dust cup.
Dust cup release button
①
②
※
Discard any debris that has gotten inside the dust
cup.
2
Remove the cyclone unit/exhaust lter/
sponge lter
Cyclone unit
Exhaust lter
Sponge lter
3
Disassemble the cyclone unit
• Turn the cyclone unit
（top）
counterclockwise
（①）,and disassemble the cyclone unit from top to
bottom
（②）.
Cyclone unit
(bottom)
Cyclone unit
(top)
①
②
4
Remove any debris and wash out with
water
• Use a cleaning brush to clean the mesh lter on
the cyclone unit
（top）
.
Charger adapter
Mesh lter
• Lightly tap the top cyclone unit, the bottom cyclone
unit, the dust cup case and the sponge lter to
remove any debris, and then wash with water.
• Tap any debris in the exhaust lter to remove it. If
dirt has become noticeable, soak in water for about
30 minutes and wash o󰀨 with running water. (Do
not scrub with a cleaning brush.)
After washing, remove all water and dry o󰀨
thoroughly.
※
If any water remains, it could get absorbed in and
cause the motor to malfunction. Thoroughly dry
o󰀨 the exhaust lter and sponge lter all the way
through in a place with good ventilation.
Cleaning and maintainance Continued

Black SCD-181P
15
6
Attach the dust cup to the main unit
① Insert the tabs on the main unit of the vacuum
cleaner into the holes on top of the dust cup.
Tab
Hole
② Push the dust cup in until it clicks into place.
Click
※
Push the dust cup rmly into place.
5
Assemble the dust cup by following these
steps in reverse
• Fit the top cyclone unit into the bottom cyclone unit
(1), and rotate it clockwise to attach it (2).
①②
Cyclone unit (top)
Cyclone unit (bottom)
• Insert the sponge lter into the cavity at the center of
the cyclone unit, attach the exhaust lter to the cyclone
unit, and attach the cyclone unit to the dust cup.
Protrusion
Protrusion
Exhaust lter
Cyclone unit
Sponge lter
Notch
※
Align the protruding part of the cyclone unit with the
notch on the dust cup case, and attach it rmly as
far as it will go.

Black SCD-181P
16
If usage time is becoming shorter even after the battery
has been charged correctly, replace the battery with a new
one. See page 4 for information about purchasing batteries
(sold separately).
■How to remove the battery
While pressing in on the battery cover on the handle,
pull it toward yourself to remove it and pull out the
battery.
※
When disposing of the battery, cover the ends with
tape to insulate them and take them to a battery
recycling location. Do not treat the used battery as
regular household trash.
Bring the lithium-ion
battery to a battery
recycling location.
How to replace the battery
■How to install the battery
Push the battery in rmly all the way, and t
the battery cover into place
Attention
●Be careful not to pinch ngers
when installing or removing the
battery.

Black SCD-181P
17
➡ ➡
Status Possible causes Remedy
If the following problems occurred during use, before requesting any repairs read the operation manual carefully and
check to see if there is any of the following.
Troubleshooting
Weak suction
power
Even after
charging, the
Battery runs out
of power quickly
➡ ➡
No power (not
working)
●Battery is depleted ●Insert the charging plug into the main unit.
➡ ➡
●Remaining battery power is low ●Insert the charging plug into the main unit.
➡ ➡
●If the battery is charged in
a location where the room
temperature is too high or too
low, it might not charge properly
●Charge the battery at a room temperature of
5~35℃and in a location that is away from direct
sunlight.
●The dust cup is not attached
properly
●Make sure the dust cup has been properly
attached. (→P11)
➡ ➡
●The battery has reached the
end of its shelf life
●If usage time is becoming shorter even after the
battery has been charged correctly, change the
battery for a new one.
（→P16）
Weak suction
power and very
noisy when in
operation
➡ ➡
●Debris has accumulated in the
dust cup
●Remove dirt (→P11)
●Do not let debris accumulate so it exceeds the full
dust cup line.
➡ ➡
●The exhaust lter has become
clogged
●Remove the dust cup and clean the exhaust lter.
( →P 14 , 15)
➡ ➡
●The main unit ventilation
ue, the suction head, or the
extension pipe have become
clogged with debris
●Clean out and remove all debris (
→P 12)
➡ ➡
The dust cup
cannot be
attached
●Th
e tabs on the main unit have
not been inserted into the holes
on the upper side of the dust cup
●Make sure that the tabs on the main unit are
rmly inserted into the holes on the upper side of
the dust cup.
（→P11）
●The charger adapter has not
been rmly plugged into the
power outlet
●Plug the charger adapter rmly into the power
outlet.
➡ ➡
The battery
cannot be
charged
●The charging time may be
changed depending on the
ambient temperature when
charging and the service time
The battery
indicator light
does not go
out when the
battery is
charging
➡
●C
harge the battery at a room temperature of 5~35℃
and in a location that is away from direct sunlight.
➡
●Charging times may be changed depending on
the room temperature and the usage time. If the
battery indicator light still does not go out even
after charging for 5 hours or more, contact the
store where you purchased this product.
➡

Black SCD-181P
18
Status Possible causes Remedy
➡ ➡
The brushroll
has stopped
moving
●The rotating part has become
entangled or clogged with
debris
●Clean the brush roll. (→P13)
➡ ➡
The main unit
and charging
adapter heat up
while charging
●The battery and circuit can
sometimes heat up due to the
charging current
●This is normal.
➡ ➡
The main unit
heats up while
in use
●The main unit can sometimes
heat up due to the battery or the
motor generating heat
●This is normal.
If the problem persists
please consult the shop where you purchase.
Warning
●Do not disassemble, repair or modify the product yourself.
Trouble shooting Continued
Specications
※1 Fully charged, the battery’s initial temperature：20℃.
※Specications are subject to change without prior notice.
Dust capacity Dust cup full 0.15L
Maximum capacity 0.3L
Charging temperature 5~35℃
Continuous
operation time※1
Standard (Approx.) 27 minutes (brushroll o󰀨)
20 minutes (brushroll on)
Turbo (Approx.) About 10 minutes
Battery Lithium ion 2-D battery
Battery capacity 1,900mAh
Battery life※1The battery can be recharged about 1,000 times
Rated power 10.8V
Charger power
(Charger adapter)
Input 100-240Ｖ~，50-60Hz
Output 13.7V ，0.5A
Time needed to charge the battery
About 4 hours (The charging time may take longer
depending on the ambient temperature when
charging and the service time)
Dimensions
(Approx.)
Include the brush nozzle and
extension pipe W224 x D245 x H1045mm
Product weigh
Main unit only 1.0kg
Suction head/extension pipe
Including the battery 1.5kg
Accessories Charger adapter, Nozzle for gaps,Cleaning brush

Black SCD-181P
19
Warranty and After-sales Service
Be sure to carefully read the following contents.
■Warranty card
Be sure to get the warranty card from the shop where
you purchase, and conrm that the relevant items have
been lled out.
If the warranty card cannot be shown within the
warranty period, the maintenance cost will be paid. So
please properly keep it.
■Within the warranty period
Warranty period: one year from the date of purchase.
The company will maintain for free according to
Warranty Terms if failure occurs within the warranty
period.
■Beyond the warranty period
Please consult the shop where you purchase. It is
necessary to pay the relevant maintenance cost.
■About the warranty period for components
The warranty period for the important components
of the product shall be one year after the company
suspends production.
■About after-sales service
For other after-sales services not mentioned here,
please consult the shop where you purchase.

Black SCD-181P
824426
250822-LVC-HYJ-02
Warranty provisions
1This carry-in warranty starts on the date of purchase and expires in ONE (1) year to cover manufacturing defects
caused during a normal use according to the operating manual as well as the precautions stated on the product and
packaging.
2To claim the carry-in warranty service, customers should bring the complete unit and accessories to our service
centre in local market during the operational hours together with this warranty card and dated original receipt/invoice.
3If
the product is conrmed to be defective by the distributor’s authorized personnel, the company at its own discretion
may repair or replace the complete or part of the product at no cost .
4Carry-in Warranty claim will be invalid and repair cost shall be paid by customer in the following situations.
(a) Failure and damage caused by improper use and unauthorized maintenance.
(b) Failure and damage caused by careless drop after purchase.
(c) Failure and damage caused by re, earthquake or other natural disasters.
(d) Failure and damage caused when the product is used for commercial purposes such as used in an industry for a
long time, or in a vehicle or a ship.
(e) Failure and damage caused by handling, transportation and other processes.
( f ) Failure to show the warranty card and dated original receipt/invoice.
(g) Date of purchase, customer name, shop name not indicated on the warranty card or altered.
5The carry-in warranty services are applicable only for products purchased in local market.
Rechargeable cyclone vacuum cleaner SCD-181P
This warranty card is a certicate for providing free repair according to the following warranty terms in case of failure
within the following period from the date of purchase.
Date of purchase ※Warranty period
From the date of purchase:
1 year (except consumables)MM DD YY
Name Address and shop name
Address and postal code
Tel ( ） - Tel ( ） -
Instruction to shop: please ll out items with ※before handing over the warranty card to the customer.
Warranty card
Customer
※
Shop