iRobot Scooba 300 series User manual

iRobot®Verro™
model 300
QUICK START GUIDE
An easy step-by-step guide to using the
iRobot Verro Pool Cleaning robot
iRobot®Verro™model 300 Quick Start Guide
© 2007 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reserved. iRobot is a registered trademark and Verro is a trademark
of iRobot Corporation. Cover photo © Veer incorporated 2002 - 2005. All rights reserved.
3002.07
Quick Start (cont...)
See Owner’s Manual
for detailed product
instructions.
Visit
www.irobot.com/usetips
for instructional photos
8
After approximately two hours, Verro will stop and the Power Supply light will
turn off. To stop Verro before the end of the cleaning cycle, switch the Power
Supply OFF.
9
Wait 20 minutes before removing Verro from the pool to allow the pump motor
to cool. Shut off and unplug the Power Supply every time you remove the
cleaner from the water. Always remember to turn the Power Supply OFF and
unplug it from the power outlet before removing the cleaner from the pool.
10
Unplug the Power Supply from the GFCI outlet. Never leave the Power Supply
plugged in when Verro is not in use.
11
Unplug the floating power cord from the Power Supply.
12
Use the floating power cord to pull Verro to the edge of the pool, then use the
handle to lift it out of the water. Water will drain from Verro as it is lifted.
CAUTION: Removing Verro by its floating power cord may cause severe damage
to the cord requiring costly repairs.
13
Store Verro and its Power Supply in a dry area out of direct sunlight. The Power
Supply is water resistant, but not waterproof, and may be damaged by rain.

How Verro Works
iRobot Verro uses a powerful motor to
draw 80 gallons of water per minute
through the filter bag. This creates strong
suction at two inlet ports under the
robot that draws dirt and debris, such as
bacteria, algae, leaves, and even coins
into the filter bag where they are trapped.
The pump motor also drives two high-
pressure jets under the robot that loosen
dirt and attached particles, which are
then vacuumed up.
Verro uses the force of the water being
pumped through the robot to hold itself
against the surface it is cleaning and to
move along it.
Each time it changes direction, Verro
automatically alters it course slightly so
that it covers the entire bottom and sides
of the pool efficiently.
iRobot®Verro™ model 300 Quick Start Guide
Instructional photos available at www.irobot.com/usetips
Tip
Clean the filter bag regularly. Verro uses
the force of the water pumped through
its filter bag to move properly. If the
filter bag is not kept clean, Verro will
not move or clean properly.
Tip
Store Verro in a dry place out of direct
sunlight at a temperature between
50 and 104 degrees Fahrenheit. The
Power Supply is water resistant, but not
waterproof and may be damaged by rain.
Important: Failure to properly store Verro
will result in loss of warranty.
Tip
iRobot recommends using the mesh
filter bag (included) when
the pool contains a significant quantity
of large debris (leaves, etc.), such
as when the pool is opened for the
season. The fine filter bag is ideal for
filtering small debris (algae, sand,
etc.) and for regular maintenance.
Tip
Periodically straighten the floating
power cord with the Detangler.
Tip
Verro’s Power Supply has an automatic
timer that shuts Verro OFF after
approximately two hours of operation.
When this happens, the power switch
will remain ON. To start another
cleaning cycle, switch the Power
Supply OFF and then back ON and
then press the reset button.
1
Uncoil the floating power cord and spread it over the surface of the water, ensuring that it is not tangled
or kinked.
6
Set the time control dial to 30 seconds.
2
Place Verro upside down in the pool and rock it from side to side to allow air to escape. Turn Verro over
and allow it to sink to the bottom of the pool so that the wheels rest on the bottom of the pool.
Warning: A Ground Fault Current Interrupter (GFCI) must be installed to
protect your electric outlet and prevent any possible electric shock.
7
Turn the Power Supply switch ON then press the reset button. The light on the Power Supply will
illuminate and Verro will start to clean your pool.
3
Place the Power Supply in a dry area at least 3.5 meters/12 feet from the pool.
3.5m/12ft
5
Ensure that the Power Supply is at least 12 feet from the pool and that the power switch is OFF. Plug
the Power Supply into a GFCI outlet. Ensure the electric outlet has been properly grounded.
Never leave the Power Supply plugged in when Verro is not in use
4
Plug the floating power cord into the Power Supply. Be sure not to force the plug as it will only
go in one way.

iRobot®Verro™
model 300
QUICK START GUIDE
An easy step-by-step guide to using the
iRobot Verro Pool Cleaning robot
iRobot®Verro™model 300 Quick Start Guide
© 2007 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reserved. iRobot is a registered trademark and Verro is a trademark
of iRobot Corporation. Cover photo © Veer incorporated 2002 - 2005. All rights reserved.
3002.07
Quick Start (cont...)
See Owner’s Manual
for detailed product
instructions.
Visit
www.irobot.com/usetips
for instructional photos
8
After approximately two hours, Verro will stop and the Power Supply light will
turn off. To stop Verro before the end of the cleaning cycle, switch the Power
Supply OFF.
9
Wait 20 minutes before removing Verro from the pool to allow the pump motor
to cool. Shut off and unplug the Power Supply every time you remove the
cleaner from the water. Always remember to turn the Power Supply OFF and
unplug it from the power outlet before removing the cleaner from the pool.
10
Unplug the Power Supply from the GFCI outlet. Never leave the Power Supply
plugged in when Verro is not in use.
11
Unplug the floating power cord from the Power Supply.
12
Use the floating power cord to pull Verro to the edge of the pool, then use the
handle to lift it out of the water. Water will drain from Verro as it is lifted.
CAUTION: Removing Verro by its floating power cord may cause severe damage
to the cord requiring costly repairs.
13
Store Verro and its Power Supply in a dry area out of direct sunlight. The Power
Supply is water resistant, but not waterproof, and may be damaged by rain.