IRONGEAR IG7141 User manual
Monitor Desk Mount
Instruction Manual V1.0
Thank you for choosing this IRONGEAR product! At IRONGEAR we
strive to provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to contact
Model: IG7141
Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We are not liable for damage or injury caused by
improper mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also
it is strictly prohibited to dismantle without professionals. Please return to the
manufacturer or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
Weight Restrictions
4.4-26.5 lbs.
(2-12 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only with
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage or injury.
WARNING
If your monitor weighs more, this mount is NOT
compatible.
Your monitor (including
accessories) CANNOT EXCEED
4.4-26.5 lbs (2-12 kg) per arm
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
01
Product Features
180°
360°
360°
C-Clamp Mounting
1.0-3.2 in.(25-80mm)
Grommet Mounting
0.8-3.5 in.(20-90mm)
02
Warning!
Do not adjust tension without monitor.
1. Ensuremonitorhas been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensurethe net weight of monitor (including accessories) is between
4.4~26.5 Ibs (2-12 kg) per arm.
Clockwise to reduce
tension(carry less weight)Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
03
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
• Please note: Not all hardware included in this package will be used.
(F) x1
5/32 in.(4mm)
Allen Key
(D)
Grommet Bolt x1
(E)
Locking Plate x1
Tools Needed (Not lncluded)
Screwdriver
M6x12mm (4pcs)
Bolt (C)
06 Cable Clip X204 C-Clamp X105 Pole Assembly X1
(D)
Butterfly Nut x1
04
(F) x1
1/8 in.(3mm)
Allen Key
(F) x1
5/32 in.(4mm)
Allen Key
13/64 in.(5mm)
Allen Key
(F)
04
02 Extension Arm x2 07 Locating Ring X2
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4 and Step 6
Supplied Part for Step 8
Bolt (A)
M4x12mm (X8)Bolt (B-1)
M4x16mm (X8)Spacer (B-2)
5mm (X8)
01 Arm X2
03 Cable Cover x1
(G)
Plastic Sleeve X2
05
1. Install the Base
A. For Clamp Mounting A-1 For Clamp Mounting
Warning:
Ensure bolts are
secured firmly.
Slide the cable clips [06] to pole
assembly [05] and secure part [a] to
pole assembly [05]
2
Detach the c-clamp entirely
1
F
5/32 in.
(4mm)
C
a
06
05
Connect part [b] to part [a] according to the thickness of the desktop
3
a
b
OR OR
a
b
a
b
a
b
06
Secure the pole assembly to the desktop
4
Warning:
Ensure bolts are
secured firmly.
B. For Grommet Mounting
Warning:
Ensure bolts are
secured firmly.
D
05
Install the grommet bolt [D] to the bottom of pole assembly [05]
1
1.0-3.1 in.
（25-80mm）
07
D
E
Warning:
Ensure bolts are
secured firmly.
Secure the pole assembly to the desktop with grommet
2
Warning:
Ensure bolts are
secured firmly.
2. Install the Arms
①Fasten the locating ring [07] at your
desired height.
②Slide the extension arms [02] to the pole
assembly [05], and attach the plastic
sleeves [G] to extension arms [02]
07
07
07
G
05
G
02
(φ10-φ50mm)
φ0.4 - φ2 in.
0.8-3.5 in.
(20-90mm)
08
Warning:
Ensure bolts are
secured firmly.
④Secure the arms [01] to the extension
arms [02] by tightening the preassembled
set screw [S] using Allen key [F]
③Attach the arms [01] to the extension
arms [02]
S
01 02
F
1/8 in.
(3mm)
Warning:
Ensure bolts are
securedfirmly.
For VESA hole pattern:
3in. (75mm) x 3 in. (75mm)
4 in. (100mm) x 4 in. (100mm)
Step 3 Attach Monitors to the Arms
3-1 Choose Proper bolts 3-2 Install Monitors to the Arms
10.1-0.2in.(3-5mm) spacing left
The tension is preset at
8.8~11 Ibs(4-5kg). After
hanging the monitor to
the mount, please
release the
monitor slowly to
prevent it from falling
suddenly.
100x100mm
75x75mm
A
Screw Driver
[Not Included]
Flat back monitor
Round back monitor
100x100mm
75x75mm
B-1
B-2
09
4. Adjust Gas Spring Tension
Be sure to keep the arm in horizontal position
during adjustment. Or else, it would be difficult
to adjust the mount or damage the mount.
1. If the monitor can stay at the desired height by itself, no adjustment needed.
2. If the monitor rises up, press the arm to keep it in horizontal position and then
use the 13/64 in.(5mm) Alley key (F) to turn the bolt clockwise(“-” direction) to
reduce tension of the arm only until the monitor can stay at the desired height by
itself.
3. If the monitor falls down, lift the arm to keep it in horizontal position and then use
the 13/64 in.(5mm) Alley key (F) to turn the bolt counter-clockwise (“+” direction)
to increase tension of the arm only until the monitor can stay at the desired height
by itself.
F
13/64 in.
(5mm)
10
5. Rotation Restriction
Proper usage directions Non-proper usage directions
6. Tilt Adjustment
“+” Clockwise: Tighten
“-” Counter-clockwise: Loosen
Situation 1: If the monitor can stay at the desired tilt angle by itself,
no adjustment needed.
Situation 2: If the monitor can not stay at the desired tilt angle by
itself, turn the bolt clockwise or counter-clockwise as shown
until the monitor can stay at the desired tilt angle by itself.
F
13/64 in.
(5mm)
11
7. Rotation Adjustment
Rotation
Only suitable for the monitors
with the center of gravity in the
center position
8. Route Cables along the Arms
12
Warning:
Ensure bolts are
secured firmly.
5
34
6
03
13
Thank you again for
choosing this IRONGEAR product!
All of us at IRONGEAR do appreciate your product purchase. We hope
that you are as happy with your product as we are designing and
manufacturing it for you. We strive to provide you with the best quality
products and services in the industry. Should you have any issues,
Table of contents
