Island Umbrella Santorini II Fiesta NU6245B User manual

www.bluewaveproducts.com
Please Do Not Hesitate to
Contact Our Consumer Hotline
at 800-759-0977
with Any Questions That May
Arise During Assembly or
Use of This Product!
NU6245B • NU6250B • NU6255B
Santorini II Fiesta 10-ft Square Cantilever
Solar LED Umbrella with Sunbrella® Fabric
Ver. 0219LP

PACKAGE CONTENTS
Please read and understand this entire manual before attempting to assemble or install the product.
In case you want to move the umbrella to a new place, please close the umbrella and pour the water out
•
•
•
•Assemble on level ground.
•Keep children away from assembly area.
Two adults are required for safe assembly.
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 10 Minutes
The tool for assembly is with the umbrella
PREPARATION
A
BG
I
H
F
CARE AND MAINTENANCE
Clean with mild soap and lukewarm water, rinse and air dry.
When not in use, close and cover the umbrella with the protective cover (included).
The umbrella must be closed in windy weather to avoid any damages.
Store the product indoors in a cool, dry place.
C
D
E
J
K
A – (1) Main Umbrella*
B – (1) Plastic Water Fillable Stand
(incl. in separate carton as NU6000JL)
C – (1) Base Pole, NUP4117
D – (1) Swivel Cover, NUP4118
E – (1) Allen Wrench, NUP4119
F – (4) Stainless Bolt, NUP4120
G – (4) Washer, NUP4121
H – (1) Threaded Knob, NUP4122
I – (1) Crank Handle, NUP4123
J – (1) Umbrella Cover, NUP4124
K – (1) Solar Panel, NUP4125
SAFETY INFORMATION
* For main umbrella replacement
please specify the item number
for your umbrella

Step 2
In case you want to move the stand,
Put the Base Pole (C)on the top of the Plastic Water Fillable Stand (B).
C
B
Step 1 Put the stand on a level ground where you intend to locate your umbrella.
ASSEMBLY INSTRUCTIONS
Carefully check all packaging materials before discarding.
Do not assemble if there are missing pieces.
Open the cap on the top of the stand & fill the stand with water.
Then tighten the cap.

Step 3 Attach the Base Pole (C) on the top of the Plastic Water Fillable Stand (B) with
Bolts (F)& Washers (G), using the Allen Wrench (E) to tighten
Step 4 Place the Swivel Cover (D) around the Base Pole (C).
C
C
B
B
D
E
F
G
Locking hole for threaded knob
Important Notice :
Pay attention to the size of the middle hole in the Swivel Cover (D).
Side A / Front Side ： +/- 1.4", Side B / Rear Side : +/- 1.7".
Side B of the Swivel Cover (D) and the locking hole on the
Base Pole (C) must be on the same side.
side B
side A
+/- 1.4”
+/-1.7”
Side B
Bottom crank hole
Bottom crank hole

1
2
1 : Insert the plug into the socket under the Solar Panel (K).
2 : Put the Solar Panel (K) on the top of umbrella and hide the plug and wire inside the groove
at the top of umbrella. Then turn the Solar Panel (K) clockwise. Do not over tighten.
Step 5 Attach the Solar Panel (K) to the top of the umbrella.

B
Step 6 Put the Main Umbrella (A) over the Base Pole (C)
Important Notice :
When you put the Main Umbrella (A) onto the Base
Pole (C), make sure the locking holes are on the
same side .
A
A
B
Locking hole for
threaded knob

B
A
Step 7 Screw the Threaded Knob (H) into the locking hole clockwise.
H

I
I
I
Bottom Crank Hole for 360 degree rotation
Middle Crank Hole for umbrella opening and closing
Top Crank Hole for canopy tilting
Step 8 There are 3 Crank Holes on your umbrella.
Top crank hole for canopy tilting,
Bottom crank hole for 360 degree rotation.
Middle crank hole for umbrella opening and closing.

B
A
Step 9 Squeezethe trigger before attempting to raise the crank housing. Insert the Crank Handle (I)
into the middle crank hole and turn clockwise to extend umbrella fully.
I
I
1
2
CAUTION:
Please pull and loosen the umbrella
ribs by hand, so they're not
entangled, before attempting to
open the umbrella by crank.

Step 10
Swith On / O
Squeeze trigger and lift up to desired height.