iSMA CONTROLLI PA-LED User manual

www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
PA-LED
User Manual
Android LED Panels

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 2 of 15
Table of Contents
1 Introduction .................................................................................................................................... 3
1.1 Revison History .......................................................................................................................................3
2 Safety Rules..................................................................................................................................... 4
3 Technical Specification ................................................................................................................. 5
3.1 PA-LED10..................................................................................................................................................5
3.2 PA-LED13..................................................................................................................................................6
4 Standards and Norms ..................................................................................................................8
4.1 EN 55022:2010+AC:2011 .....................................................................................................................8
4.2 EN 61000-3-2:2014................................................................................................................................8
4.3 EN 61000-3-3:2013................................................................................................................................8
4.4 EN 55024:2010 + A1:2015 ...................................................................................................................8
4.5 EN 60950-1:2006 + A11:2002 + A1:2010 + A12:2011 + A2:2013...............................................8
5 Dimensions ..................................................................................................................................... 9
5.1 PA-LED10..................................................................................................................................................9
5.2 PA-LED13............................................................................................................................................... 10
6 Interfaces.......................................................................................................................................11
6.1 PA-LED10............................................................................................................................................... 11
6.2 PA-LED13............................................................................................................................................... 11
7 Installation.....................................................................................................................................12
7.1 PA-LED10............................................................................................................................................... 12
7.2 PA-LED13............................................................................................................................................... 13
8 Android System............................................................................................................................15

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 3 of 15
1 Introduction
The PA-LED family are LCD room panels with LED bars, designed for commercial
applications. Powered by the Android operating system and equipped with the dedicated
iC SmartView application, these panels offer excellent operation in a variety of
environments
Available in a variety of size options, these LCD room panels with LED bars are versatile
and customizable solutions for a wide range of settings in residential and commercial
buildings. Their sleek and modern design, complemented with a metal wire slot for a
clean and organized installation, ensures they seamlessly blend into any environment.
These panels come with a built-in multicolor LED bar that can be customized to suit
specific needs and integrated into applications for enhanced functionality. With a 10-point
capacitive touchscreen, they provide an exceptional viewing experience. Whether there is
a need for a room management device for hotels, conference rooms, or a dynamic
display in lobbies, these panels are up to the task.
In addition to their stunning design and capabilities, the panels offer advanced features,
including Power over Ethernet (POE) for convenient power supply, and the iC SmartView
app for kiosk mode and remote control. The multitude of interfaces and built-in features
make these panels a versatile solution for a wide range of applications.
Figure 1. PA-LED panels
1.1 Revison History
Rev. Date Description
1.0 10 Nov 2023 First edition
Table 1. Revision history

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 4 of 15
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
2 Safety Rules
Improper wiring of the product can damage it and lead to other hazards. Make sure
that the product has been correctly wired before turning the power on.
Before wiring or removing/mounting the product, make sure to turn the power off.
Failure to do so might cause an electric shock.
Do not touch electrically charged parts such as power terminals. Doing so might cause
an electric shock.
Do not disassemble the product. Doing so might cause an electric shock or faulty
operation.
Use the product only within the operating ranges recommended in the specification
(temperature, humidity, voltage, shock, mounting direction, atmosphere, etc.). Failure
to do so might cause a fire or faulty operation.
Firmly tighten the wires to the terminal. Failure to do so might cause a fire.
Avoid installing the product in close proximity to high-power electrical devices and
cables, inductive loads, and switching devices. Proximity of such objects may cause an
uncontrolled interference, resulting in an instable operation of the product.
Proper arrangement of the power and signal cabling affects the operation of the entire
control system. Avoid laying the power and signal wiring in parallel cable trays. It can
cause interferences in monitored and control signals.
It is recommended to power controllers/modules with AC/DC power suppliers. They
provide better and more stable insulation for devices compared to AC/AC transformer
systems, which transmit disturbances and transient phenomena like surges and bursts
to devices. They also isolate products from inductive phenomena from other
transformers and loads.
Power supply systems for the product should be protected by external devices limiting
overvoltage and effects of lightning discharges.
Avoid powering the product and its controlled/monitored devices, especially high
power and inductive loads, from a single power source. Powering devices from a single
power source causes a risk of introducing disturbances from the loads to the control
devices.
If an AC/AC transformer is used to supply control devices, it is strongly recommended
to use a maximum 100 VA Class 2 transformer to avoid unwanted inductive effects,
which are dangerous for devices.
Long monitoring and control lines may cause loops in connection with the shared
power supply, causing disturbances in the operation of devices, including external
communication. It is recommended to use galvanic separators.
To protect signal and communication lines against external electromagnetic
interferences, use properly grounded shielded cables and ferrite beads.
Switching the digital output relays of large (exceeding specification) inductive loads can
cause interference pulses to the electronics installed inside the product. Therefore, it
is recommended to use external relays/contactors, etc. to switch such loads. The use
of controllers with triac outputs also limits similar overvoltage phenomena.
Many cases of disturbances and overvoltage in control systems are generated by
switched, inductive loads supplied by alternating mains voltage (AC 120/230 V). If they
do not have appropriate built-in noise reduction circuits, it is recommended to use
external circuits such as snubbers, varistors, or protection diodes to limit these effects.

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 5 of 15
3 Technical Specification
3.1 PA-LED10
Power supply Power input 12 V DC / 1.5 A
PoE+ IEEE802.3at, class 4, 25.5 W
Power adapter for EU, US, and UK UL listed
100-240 V AC
Platform Operating system Android 11
CPU CPU Quad-core Cortex A17, RK3288
RAM 2 GB
Internal memory 16 GB
Display Screen type LCD
Touch type 10-point capacitive touch screen
Size 10.1 in
Aspect ratio 16:10
Resolution 1280:800
Contrast 800:1
Luminance 250 cd/m2
Active area 217.40 x 136.40 mm / 8.56 x 5.37 in
View angle 85/85/85/85(L/R/U/D)
LED light bar LED light bar with RGB and mixed colors
Media Audio MP3/WMA/AAC, etc.
Video MPEG-1, MPEG-2, MPEG-4, H.265, H.264,
VC-1,VP8, etc.,support up to 4K
Photo JPEG
Interfaces Card slot SD card
USB USB 3.0 host
USB for serial (RS232)
micro USB OTG

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 6 of 15
RJ45 RJ45 with PoE+ (IEEE802.3at), class 4,
25.5W
WiFi 802.11 b/g/n
Bluetooth Bluetooth 4.2
Audio 3.5 mm earphone
2 speakers, 1.5 W
Temperature Operating 0°C to 40°C/32°F to 104°F
Storage -20°C to 60°C/-4°F to 140°F
Humidity Relative humidity 20% to 80% RH
Housing Mounting VESA 75*75 mm compatibility
Dimensions Width 259.36 mm/10.21 in
Length 178.36 mm/7.02 in
Height 28.00 mm/1.10 in
Table 2. Technical specification of the PA-LED10 panel
3.2 PA-LED13
Power supply Power input 12 V DC / 2 A
PoE+ IEEE802.3at, class 4, 25.5 W
Power adapterfor EU, US, and UK UL listed
100-240 V AC
Platform Operating system Android 11
CPU RK3399 dual-core A72+quad-core A53
RAM 2 GB
Internal memory 16 GB
Display Screen type LCD
Touch type 10-point capacitive touch screen
Size 13.3 in
Aspect ratio 16:9
Resolution 1920:1080

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 7 of 15
Contrast 800:1
Luminance 250 cd/m2
Active area 293.76 x 165.24 mm / 11.57 x 6.51 in
View angle 85/85/85/85
LED light bar LED light bar with RGB and mixed colors
Media Audio MP3/WMA/AAC, etc.
Video MPEG-1, MPEG-2, MPEG-4, H.265, H.264,
VC-1,VP8, etc.,support up to 4K
Photo JPEG
Interfaces Card slot SD card, max. support up to 64 GB
USB USB 3.0 host
USB for serial (RS232)
micro USB OTG
RJ45 RJ45 with PoE+ (IEEE802.3at), class 4, 25.5W
WiFi 802.11a/b/g/n/ac
Bluetooth Bluetooth 4.2
Audio 3.5 mm earphone
Microphone
2 speakers, 3 W
Temperature Operating 0°C to 40°C/32°F to 104°F
Storage -20°C to 60°C/-4°F to 140°F
Humidity Relative humidity 20% to 80% RH
Housing Mounting VESA 75*75 mm compatibility
Dimensions Width 333.00 mm/13.11 in
Length 225.00 mm/8.86 in
Height 28.50 mm/1.12 in
Table 3. Technical specification of the PA-LED13 panel

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 8 of 15
4 Standards and Norms
4.1 EN 55022:2010+AC:2011
Electromagnetic compatibility of multimedia equipment. Emission Requirements.
4.2 EN 61000-3-2:2014
Electromagnetic compatibility (EMC). Limits for harmonic current emissions for
equipment input current ≤ 16 A per phase).
4.3 EN 61000-3-3:2013
Electromagnetic compatibility (EMC). Limits for voltage changes, voltage fluctuations and
flicker in public low-voltage supply systems, for equipment with rated current ≤ 16 A per
phase.
4.4 EN 55024:2010 + A1:2015
Information technology equipment. Immunity characteristics. Limits and methods of
measurement.
4.5 EN 60950-1:2006 + A11:2002 + A1:2010 + A12:2011 + A2:2013
Information technology equipment. Safety General requirements specifies requirements
intended to reduce risks of fire, electric shock or injury for the OPERATOR and layman
who may come into contact with the equipment and, where specifically stated, for a
SERVICE PERSON.

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 9 of 15
5 Dimensions
5.1 PA-LED10
Figure 2. PA-LED10 dimensions

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 10 of 15
5.2 PA-LED13
Figure 3. PA-LED13 dimensions

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 11 of 15
6 Interfaces
6.1 PA-LED10
Figure 4. PA-LED10 interfaces
6.2 PA-LED13
Figure 5. PA-LED13 interfaces

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 12 of 15
7 Installation
7.1 PA-LED10
Figure 6. PA-LED10 installation

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 13 of 15
7.2 PA-LED13

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 14 of 15
Figure 7. PA-LED13 installation

PA-LED User Manual
www.ismacontrolli.com
DMP298en | 1st Issue rev. 0 | 11/2023
page 15 of 15
•
•
•
•
8 Android System
For a better user experience, during a long-term operation of the device, make sure that
the auto-update function in the Play store is turned off:
Open the Google Play Store app;
In the top right corner, tap the profile icon;
Tap Settings>Network Preferences>Auto-update apps;
Select the Do not auto update apps option.
WARNING!
In case any custom modifications or any other changes are introduced to the Android
system originally installed on the equipment, the warranty automatically expires. The
only exception is when the iSMA CONTROLLI itself announces the possibility of
introducing custom modifications to the Android system originally installed on the
equipment precisely specifying the range of such modifications.