Ismart AMCE200U3 User manual

USB3.0 HD PTZ Camera
User Manual V1.2

Safety Notes
Before installing the device, please read this manual carefully and follow instructions
indicated to ensure proper operation. Please keep this manual for future reference.
Please powering on the device, please check the input power voltage carefully, the camera
accepts DC12V, otherwise, it may cause damage to the camera.
Please put power, video and control cables at safe place in order not to cause malfunction to
the device.
Please put the device into use at required working temperature and humidity, working
condition of the device is 0℃~+40℃，humidity at＜90﹪. Please avoid to have unrelated
objects get into the device like corrosive liquid that may cause damage / danger.
Please avoid shock, vibration, soaking may cause to the device when transporting and
installing, otherwise, it may cause damage to the camera.
Please only refer to authorized personnel to repair the device, do not disassemble the
camera by yourself.
Only use shielded control and video cables, and the cables should be connected separately
in order to ensure proper use. Do not aim the camera lens at sunlight or strong lights that
may cause damage to the imaging system of the device.
Please use soft cloth to clean the device, do not use strong or abrasive detergent to clean
that will damage the device’s housing / lens.

Contents
PRODUCT OVERVIEW--------------------------------------------------------- 1
FEATURES------------------------------------------------------------------------------ 1
PACKING LIST--------------------------------------------------------------------------- 1
MAIN PARTS AND CONTROLINTERFACES -------------------------------------------- 2
DIP SWITCH SETTING ------------------------------------------------------------------ 3
REMOTE CONTROL--------------------------------------------------------------------- 4
CABLE CONNECTING --------------------------------------------------------- 6
INSTALLATION ---------------------------------------------------------------- 7
DESKTOP MOUNT INSTALLATION ----------------------------------------------------- 7
WALL MOUNT INSTALLATION ---------------------------------------------------------- 7
CEILING MOUNT INSTALLATION ------------------------------------------------------- 8
POLE MOUNT INSTALLATION ---------------------------------------------------------- 9
AMCAP CAPTURE SOFTWARE --------------------------------------------- 10
DRIVER INSTALLATION OF USB VIRTUAL SERIAL PORT ----------------- 10
MENU SETTINGS ------------------------------------------------------------ 11
MENU CONFIGURATION--------------------------------------------------------------- 11
MENU EXPLANATION------------------------------------------------------------------ 15
VIDEO ---------------------------------------------------------------------------------- 16
EXPOSURE ---------------------------------------------------------------------------- 16
WHITE BALANCE----------------------------------------------------------------------- 17
PAN/TILT/ZOOM------------------------------------------------------------------------ 17
SYSTEM-------------------------------------------------------------------------------- 18
STATUS -------------------------------------------------------------------------------- 19
RESTORE DEFAULTS------------------------------------------------------------------ 19
LIST OF SPECIAL PRESET COMMANDS----------------------------------------------- 19
ANNEX 1 TECHNICAL SPECIFICATIONS------------------------------------ 20
ANNEX 2 SIZE AND DIMENSION -------------------------------------------- 22

ANNEX 3 SW1 DEFINITION -------------------------------------------------- 23
TROUBLESHOOTING-------------------------------------------------------- 25

1
PRODUCT OVERVIEW
Features
2.14MP, 1/2.8” CMOS sensor;
USB3.0 high speed raw data output,
supports USB2.0 output;
Standard UVC1.1 protocol;
Support full HD output at maximum
1080P60 format;
12x optical zoom, 12x digital zoom/10x
optical zoom, 12x digital zoom;
72.5 degree wide view angle;
Provide one channel USB3.0 and one
channel DVI-D HD video output;
Has RS232 in, RS232 out and RS485
control interfaces;
Special PTZ driving system to ensure
precise positioning;
Built-in OSD menu;
With an IR remote control;
Has image flip function, suitable for stand
and suspended installation;
Supports VISCA and PELCOD
communication protocols, daisy chain is
possible.
Packing List
When you open the package, please make
sure below items are included. If any items is
missing, please contact your supplier.
PTZ Camera x 1
Power Adapter x 1
Remote Control x 1
RS-232 Control Cable x 1
USB Cable x 1
manual（1）

2
Main Parts and Control
Interfaces
PTZ Camera
Front Part
1 Camera Module
2 Remote Control Sensor
3 Power Indicator
4 Communication Indicator
Rear Part
5 USB3.0
6 DVI
7 RS-232IN/IR
8 RS-232OUT/RS-485
9 Power Input（DC12V）
Bottom Part
10 Locating Hole
Used to define installation direction of the
camera.
11 Installation Hole
1/4” inch screw, used to fix the camera.
12 DIP Switch
Used to set address, protocol, baud rate
and other parameters.

3
DIP Switch Setting
Before operating the camera, please set
camera’s address, baud rate protocol and etc.
through its DIP switch located at the bottom
part of the camera. There are two switches
named SW1 and SW2.
Note
The SW1 and SW2 switches
look the same, their settings are
different. SW1 is used to set
camera’s address and mounting
types, while SW2 is used to set
camera’s control protocol and
baud rate.
Default Settings
Camera Address
1
Baud Rate
9600bps
Protocol
VISCA
Video Output Format
1080P25
Mounting Type
Stand
SW1 Settings
Use DIP1 to DIP6 to set 64 address accordingly.
DIP7 is reserved. DIP8 is used to set camera’s
mounting type. Please refer to Annex 3 for
detailed SW1 definitions.
SW2 Settings
Use SW2 to set camera’s protocol, baud rate.
Use DIP1 and DIP2 to set camera’s protocol,
use DIP 3 and DIP4 to set camera’s baud rate.
DIP5~DIP8 switches are reserved.
Note
It requires a reboot of the PTZ for
the switch setting to take effect.
SW2
DIP No.
1
2
Protocol
OFF
OFF
VISCA
ON
OFF
PELCO- D
OFF
ON
PELCO- P
ON
ON
-
DIP No.
3
4
Baud
Rate
OFF
OFF
2400
ON
OFF
4800
OFF
ON
9600
ON
ON
38400

4
Remote Control
1 HOME button
Press HOME button, camera moves to
initial position where both pan and tilt angle
is zero.
2 Camera Selection Button
Used to switch among 4 cameras, press 1-4
number buttons to control cameras with 1-4
address respectively. For example, press
button 1 to control the camera with address
1.
3 Focus
Press “AUTO” button to switch to Auto
Focus mode, press “MANU” button to
switch to Manual Focus mode.
“ ”button to Focus Near
“ ”button to Focus Far
“ ”button to Auto Focus once every time
it is pressed, then switch back to Manual
Focus mode.
4 Iris
Press“ ”button to reset iris value to
default. “ ”button to Iris Open
“ ”button to Iris Close.
5 Menu
Press MENU button to enter / exit menu.
6 Data
Press DATA button to turn on / off display
of pan tilt angel, zoom times and title info
7 Number Keys
Used to input numbers, for example, preset
number.
8 Cancel
Used to delete number inputted.
9 Power