Ismart AMCE220NV3 User manual

IP HD PTZ Color Video
Camera
User Manual V1.0

SAFETY NOTICE-IMPORTANT!!!
The following important notes must be followed carefully to run the camera and respective
accessories in total safety. The camera and relative accessories are called video system in this
section.
Before installing the camera, please read this manual carefully. Please follow installation
instructions indicated in this manual during installation. Please keep this manual for future
use.
The installation should be performed by qualified service personnel or system installers in
accordance with all local rules.
Before powering on the camera, please check the power voltage carefully. Make sure that
you are using the correct power source.
Please put the power cable, video cable and control cable in safe place.
Do not operate the camera beyond the specified temperature and humidity. Working
temperature range of the camera is between 0℃and +40℃. The ambient humidity range is
less than 90﹪.
During transporting, avoid violent shake or force to the camera.
To prevent electric shock, do not remove screws or housing of the camera. There are no
self-serviceable parts inside. Refer to qualified service personnel for servicing.
Video cable and RS485 cable should be kept far away from other cables. Shielded and
independent wiring is necessary for video and control cables.
Never aim the lens of the camera at the sun or other extremely bright objects. Otherwise, it
may cause damage.
When cleaning the camera, please use soft cloth. If the camera is very dirty, wipe it off gently
with a soft cloth moistened with a weak solution of water and a neutral kitchen detergent.
Wring all liquid from the cloth before wiping the camera, then wipe off all remaining dirt with a
soft, dry cloth. Use lens cleaning paper to clean the lens.

Do not move the camera head manually. In doing so would result in malfunction of the
camera. Do not hold the camera head when carrying the video camera.
This camera is for indoor use only. It is not designed for outdoor use.
Make sure the camera is not directly exposed to rain and water.
Make sure the camera is far away from area where radiation, X-rays, strong electric
waves, or magnetism is generated.

CONTENTS
ABOUT THE PRODUCT-------------------------------------------------------- 1
FEATURES -------------------------------------------------------------------------------- 1
LIST OF PARTS &ACCESSORIES ------------------------------------------------------------ 1
MAIN PARTS &INTERFACES ---------------------------------------------------------------- 2
DIP SWITCHES SETTINGS ------------------------------------------------------------------ 4
REMOTE CONTROLLER --------------------------------------------------------------------- 5
INSTALLATION ---------------------------------------------------------------- 7
DESKTOP MOUNT INSTALLATION ------------------------------------------------------------ 7
WALL MOUNT INSTALLATION ---------------------------------------------------------------- 7
(WALL BRACKET SUPPLIED SEPARATELY)---------------------------------------------------- 7
CEILING MOUNT INSTALLATION-------------------------------------------------------------- 8
CONNECTIONS ---------------------------------------------------------------- 9
MENU SETTINGS ------------------------------------------------------------ 10
MENU CONFIGURATION-------------------------------------------------------------------- 10
MENU EXPLANATION ---------------------------------------------------------------------- 14
VIDEO ----------------------------------------------------------------------------------- 15
EXPOSURE ------------------------------------------------------------------------------- 15
COLOR----------------------------------------------------------------------------------- 16
PAN/TILT/ZOOM--------------------------------------------------------------------------- 17
SYSTEM---------------------------------------------------------------------------------- 17
STATUS ---------------------------------------------------------------------------------- 18
RESTORE DEFAULTS ---------------------------------------------------------------------- 18
LIST OF SPECIAL PRESET COMMANDS ------------------------------------------------------ 18
NETWORK CONNECTION --------------------------------------------------- 19
LAN CONNECTION------------------------------------------------------------------------- 19
WAN CONNECTION ------------------------------------------------------------------------ 19
CLIENT SOFTWARE INSTRUCTION----------------------------------------- 22
SEARCH AND LIST THE CAMERA------------------------------------------------------------ 22
REMOTE CONFIGURATION ----------------------------------------------------------------- 23
ANNEX 1 TECHNICAL SPECIFICATIONS------------------------------------ 33
ANNEX 2 SIZE AND DIMENSION -------------------------------------------- 35
ANNEX 3 SW1 DEFINITION-------------------------------------------------- 36

TROUBLESHOOTING-------------------------------------------------------- 38

1
ABOUT THE PRODUCT
Features
1/2.8 inch CMOS sensor, 2.14 megapixel;
H.265, H.264 video compression;
3G-SDI, DVI output;
Support 1080p60 video output;
20x optical zoom, 12x optical zoom;
20X: Max FOV: 59.5°;
12X: Max FOV: 72.5°;
Dual stream, supporting multi-levels
configuration of video quality;
1 channel audio input and 1 channel output;
Max. 64G TF card for local storage;
Precise driving system with high reliability
and precision;
Support multi protocols & control interfaces
and Daisy chain;
OSD menu;
With IR remote controller;
Smart AE technology to effectively avoid
the interference of complicated lights from
projectors ,monitors etc;
Desktop/Ceiling/ Wall mount optional.
List Of Parts & Accessories
When you open the box, check all accessories
according to the packing list.
Camera (1)
Power Adapter (1)
Remote Controller (1)
RS-232 Control Cable (1)

2
Main Parts & Interfaces
Camera
Front View
1 Camera Module
2 IR Sensor
3 Power Indicator
4 Communication Indicator
Rear View
5 TF Card Slot
6 USB
7 RJ45 (Network)
8 HDMI Video Output
9 3G-SDI
10 Audio
11 RS-232IN/IR
12 RS-232OUT/RS-485
13 Power（DC12V）
RS-232IN/IR Pin Definition
Number
Definition
1 /
2 /
3 TXD
4 GND
5
RXD
6 GND
7 IR
8 /

3
Bottom View
14 DIP Switch
Set camera address, protocol, baud rate,
video format and mounting type.
15 Mounting Hole
1/4”inch screw thread for fixing camera.
16 Locating Hole
To define installation direction of camera.
RS-232OUT/RS-485 Pin Definition
Number Definition
1
/
2 /
3 TXD
4 GND
5 RXD
6
GND
7 485+
8 485-

4
DIP Switches Settings
Before installing and operating the camera,
set the camera address, baud rate and video
output format etc through DIP switches. The
camera has two 8-digit DIP switches: SW1
and SW2 as below:
Default Settings
Address
1
Baud Rate
9600bps
Protocol
VISCA
Video Format
1080P25
Mounting Type
Desktop Installation
SW1 settings
No 1~6 are used to set camera address, the
DIPs adopt binary system. No. 8 is used to set
mounting type. Refer to page 36 for details.
SW2 settings
No. 1 and 2 of SW2 is used to set protocol; no.
3 and 4 is used to set baud rate; No. 5, 6, 7, 8
is used to set video output format. Refer to
below chart for details:
SW2
DIP No.
1
2
Protocol
OFF
OFF
VISCA
ON
OFF
PELCO- D
OFF
ON
PELCO- P
ON
ON
Reserved
DIP No.
3
4
Baud
Rate(bps)
OFF
OFF
2400
ON
OFF
4800
OFF
ON
9600
ON
ON
38400
DIP No.
5
6
7
8
Video
Format
OFF
OFF
OFF
OFF
1080P60
ON
OFF
OFF
OFF
1080P50
OFF ON OFF OFF 1080I60
ON
ON
OFF
OFF
1080I50
OFF
OFF
ON
OFF
720P60
ON
OFF
ON
OFF
720P50
OFF
ON
ON
OFF
1080P30
ON
ON
ON
OFF
1080P25
When No.5~8 is all ON, camera address,
protocol, baud rate, video format and
mounting type can be programmed by OSD
menu. Please refer to page18 for detais of
changing video formats through special
presets.

Note
PTZ reboot is necessary for the new setting
to take effect.

Note
SW1 is used to set address, and mounting
type, SW2 is used to set protocol, baud
rate and video output format.