iSmartAlarm icamera keep User manual

iSmartAiarm™
I
•

Package
Contents
1 iCamera
KEEP,
1 Power Adapter, 1Aluminum
Mounting
Bracket, 1
Mounting
Kit, 1 Quick
Installation Guide
Please read all instructions prior
to
beginning setup.
How
to
add
a
new
iCamera
KEEP
Adding
a
new
iCamera
KEEP
as
a stand-
alone
device
(without
a CubeOne™)
• Power
on
the
iCamera
KEEP
with
the
provided
power
adapter.
• Ensure your smartphone
is
connected
to
your
home
Wi-Fi network.
• Download
the
iSmartAiarm
app
from
the
App Store
or
Google Play Store.
• Sign
up
for
an
iSmartAiarm accountand
follow
the
app
'sinstructions
to
complete
the
setup.
Adding
an iCamera
KEEP
to
an existing
iSmartAiarm
system
• Power
on
the
iCamera
KEEP
with
the
provided
power
adapter.
• Ensure yoursmartphone
is
connected
to
your
home
Wi-Fi network.
• Login
to
the
iSmartAiarm
app
on
your
smartphone.
Note:
Your
accountmustbe aSuperuser
or
Administratoron the
existing iSmartAiarm system.
• Navigate
to
the
iCamera page,
tap
"add"
on
the
upper
right
corner and
follow
the
app's
instructions
to
complete
the
setup.
(
As
shown in the picture
on
the
right
)
•••••
40
3:
20PM
·-
iCamera
Add
No
iCameras
have
been
added
.
Tap
"Add" to
setup
an
iCamera
.
- -
"'-
-

How to mount the iCamera KEEP on the wall
1. Place the mounting bracket against the wall. Mark
screw hole positions and drill
two holes into the
wall at these locations. Leave at least 4.5 inch I
11 Omm on top and 1.25 inch I 30mm of open
space
on each side to allow the iCamera KEEP to
movefreely.
2. For stone, brickand drywall, insert a wall anchor(included) into each hole. Do not use wall
anchors
if wall is not stone, brick, or drywall. Screw the longer screw into the existing holes
or wall anchors. Leave each screw exposed 0.21 inch I 5. 0mm out from the wall.
3. Ensure
the power cable is plugged in and exits through the base's opening space. Use three
short screws
to secure the iCamera KEEP to the bracket.

4. Place the bracket onto the two screws
previously installed in wall.
Warranty Information
• This product comes with a 1-year warranty that cannot beexcluded under your local
Consumer
Law.
• You are entitled to a replacement or refund for a major failure of the product and for
compensation forany other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable qualityand the
failure does not amount to major failure.
• Opening the iCamera
KEEP's shell or in any way re-programming the iCamera KEEP will void
any and all warranties.
• The manufacturerand distributors are
not responsible for any known or unknown legal
liability resulting
from negligence, incorrect operation, or usage.
General Safety and Precautions
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada.
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.

This device complies with Industry Canada licence-exempt
RSS
standard(s). Operation
is
subject
to
the following
two
conditions:
(1)
this device may not cause interference,
and
(2)
this device must accept any interference, including interference that may cause
undesired operation of the device.
This device complies with part 15
of
the FCC Rules. Operation is subject to the
following
two
conditions:
(1)
This device may not cause harmful interference, and
(2)
this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class
8 digital device, pursuant to part 15
of
the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used
in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur
in
a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by
one or more
of
the
following measures:
-Reorient
or relocate the receiving antenna.
-Increase
the separation between the equipment and receiver.
-Connect
the equipment into
an
outlet on a circuit different from that to which the
receiver is connected.
-Consult
the dealer or
an
experienced radio!TV technician for help.
Changes or modifications not expressly approved by iSmart Alarm,Inc. could void the
user's authority to operate the equipment.
CE:
A
Madefor
w
iPhone

"Made for iPod," "Made for iPhone," and "Made for iPad" mean that
an
electronic
accessory has been designed to connect specifically
to
iPod, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation
of
this device or its compliance
with safety and regulatory standards. Please note that the use of this accessory with
iPod, iPhone, or iPad may affect wireless performance.
For detailed operating instructions and updates, please visit www.iSmartAiarm.com