iTD ITD55OFT5K1 User manual

ITDTechnologyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
1
USER MANUAL
MODEL：ITD55OFT5K1

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
2
CONTENTS
* Safety Instructions ……………………………………………………………………3
* Basic Parameters ………………………………………………………………………4~5
* OSD MENU Function Key ……………………………………………………………5
* System Setup ……………………………………………………………………………6~8
* Mechanical Drawing ……………………………………………………………………8
* Solutions for Common Problems ………………………………………………9
* Typical Applications ……………………………………………………………………9
* How to Contact Us ………………………………………………………………………9

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
3
Safety Instructions
1. Read these safety instructions carefully.
2. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray
detergents for cleaning.
3. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
4. Keep this equipment away from humidity.
5. Put this equipment on a reliable surface during installation. Dropping it or letting it fall from high distance may cause
damage.
6. The openings on the enclosure are for air convection. Protect the equipment from overheating.
7. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
8. Position the power cord so that people cannot step on it. Do not place anything over the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient over
voltage.
11. Never pour any liquid into an opening. This may cause fire or electrical shock.
12. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel.
13. If one of the following situations arises, get the equipment checked by service personnel:
A) The power cord or plug is damaged.
B) Liquid has penetrated into the equipment.
C) The equipment has been exposed to moisture.
D) The equipment does not work well, or you cannot get it to work according to the user’s manual.
E) The equipment has been dropped and damaged.
F) The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -10℃OR ABOVE 60℃. THIS MAY DAMAGE THE EQUIPMENT.

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
4
BASIC PARAMETERS
2. 1 General
Model ITD55OFT5K1
IP IP65(for front panel only)
Outline Dimensions Width: 1276.6mm Height: 747.4mm Depth: 60mm
Weight（N.W/G.W）42.2Kg / 48.3Kg (Approx.)
Packing Dimension 1389(W) × 850(H) × 190(D)mm
Speakers 8Ω10W
LCD Type 55” Active matrix TFT-LCD
Video Input VGA and DVI-I, HDMI, Audio
Recommend Resolution 1920×1080@60Hz,75Hz
OSD controls Allow On-Screen Adjustments of Brightness, Contrast Ratio, Auto-adjust, Phase,
Clock, H/V Location, Languages, Function, Reset
Power Supply
Type: Internal Power Supply
Input (line) Voltage: 100-240 VAC
Output Voltage/Current: 12V
Power Consumption ＜160W
Mount Interface 1)VESA 300mm×400mm
2)Side Mounting Brackets (Optional)
Regular Warranty 1 Year for TFT Panel and 2 Years for Others
Agency Approval FCC，CE，RoHS Certified
2. 2 LCD Specification
Active Area(mm) 1209.6(H) x 680.4(V)
Resolution 1920×1080
Dot Pitch(mm) 0.630×0.630
Nominal Input Voltage VDD +12V(Typ)
Viewing angle (L/R/T/B) 89°/89°/89°/89°
Contrast 1200:1
Luminance(cd/m2) 400
Response
Time(Rising/Falling)
8s
Support Color 16.7M
Screen Scanning 60Hz
Backlight MTBF(hr) 50000h
2.3 Touch Screen Specification

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
5
Type Projected Capacitive Touch Screen
Resolution 4096×4096
Light Transmission 85%±5%
Touch Life Cycle 50 millions times
Touch Response time 5ms
Touch System Interface USB A type
Operating Temperature -10～60°C
Operating System Support Plug and Play for Windows 7/8/10,Linux Kernel 3.18.12 or above
Drivers for Windows CE/XP, Android
2.4 Internal Power Supply
Input 100-240 VAC, 50-60 Hz
MTBF 50000 hr at 25°C
2.5 Environment
Operating Temp. -10～50°C
Storage Temp. -10～60°C
Operating RH: 20%～80%
Storage RH: 10%～90%
OSD MENU FUNCTION KEY
A) [AUTO] key is designated for invoking AUTO ADJUST function at any time once is pressed for H-position, V-position,
Pixel Clock and Phase for an optimal image.
B) [+] key is designated for selection function in up direction in OSD menu and also to increase the value on selected
function.
C) [Power] Key is designated for Power On/Off
D) [-] key is designated for selection function in down direction in OSD menu and also to decrease the value on selected
function.

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
6
E) [Menu] Key is designated for Menu/Enter function depending on the selected item. Pressing [Menu] can invoke OSD
menu. After that, [Menu] is also an entry key.
System Setup
4.1 Preparing for First-time Use
Before you start to set up the LCD Monitor, you should have at least the following items ready in your accessory box:
A) 12V DC Power Adapter(below 24” only);
B) Power Cord for Adapter;
C) 1.8m VGA cable/DVI cable/HDMI cable;
D) USB cable(A-A)
4.2 I/O arrangement
NO. Description
1 DC2.0 IN
2 HDMI IN
3 DVI IN
4 VGA IN
5 PC AUDIO IN
6 EARPHONE OUT
4.2.1 VGA (D-SUB DB15) Signal Definitions:

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
7
4.2.2 DVI Signal Definitions：
4.2.3 HDMI Signal Definitions：
PIN DESCRIPTION
1 TMDS Data2+
2 TMDS Data2 Shield
3 TMDS Data2–
4 TMDS Data1+
5 TMDS Data1 Shield
6 TMDS Data1–
7 TMDS Data0+

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
8
8 TMDS Data0 Shield
9 TMDS Data0–
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock–
13 CEC
14 Reserved (N.C. on device)
15 SCL
16 SDA
17 DDC/CEC Ground
18 +5V Power
4.3 Setup the Driver
A) Make sure the touchscreen USB Cable is properly connected. The setup program cannot configure the
touchscreen without it.
B) Insert the CD Kit into your PC system’s CD drive.
C) Click the SETUP.EXE installation program. The Setup program begins to execute and load the driver.
D) Follow the instructions displayed on the screen. Make your selections carefully when answering questions to
complete the installation.
Mechanical Drawing

ITDTechn o logyCo.,LTD
www.itd‐tech.com
SPECIFICATION
NO
VER 1.0
TIME 2014.2.28
EDIT Mark
9
Solutions to Common Problems
Problem Suggestion(s)
The monitor does not respond
after you turn on the system.
1) Check that the monitor’s Power Switch if it is on.
2) Turn off the power and check the monitor’s power cord and signal cable for
proper connection.
Characters on the screen are dim. Refer to the Touch monitor Adjustments section to adjust the brightness.
The screen is blank. 1) During operation, the monitor screen may automatically turn off as a result
of the Power Saving feature. Press any key to see if the screen reappears.
2) Refer to the Touch monitor Adjustments section to adjust the brightness.
Screen flashes when initialized Turn the monitor off and then turn it on again.
“Out of Range” display Check to see if the resolution of your computer is higher than that of the LCD
display.
Touch doesn’t work Make sure the touch cable is securely attached at both ends.
Typical Application
Banking Automation
Gaming/Casino Systems
Self-Service Kiosks
Entertainment
Transport and Ticketing
Customized Solutions
How to Contact us
After-Sales Service Center ： 3005, Chuangxingda Business Center, NO38, LiuXian 3rd Rd,72 Area, Bao'an,
Shenzhen, China
Tel ： [phone]
[email protected]
www.itd-tech.com