ITI 126390 User manual
POB 381, Westfield, MA 01086
33 Airport Road, Westfield, MA 01085
INSTRUMENT
TECHNOLOGY, INC.
OPERATION MANUAL
MODEL 126390
6.4” TOTE VISION MONITOR
INTRODUCTION
Thank you for selecting Instrument Technology, Inc. (ITI) to fulfill your remote viewing needs.
Since 1967, ITI has been the Leader in Remote Viewing. The only company of its type doing all its manufacturing
in the United States, ITI consistently provides cutting edge technology to customers world-wide.
ITI specializes in the design, development and manufacture of Remote Viewing Instruments (RVI) and systems
including Borescopes, Fiberscopes and Videoscopes.
ITI offers over 2,000 standard products as well as products custom designed for unique applications. No matter
which ITI product is used, our customers find they are able to observe hostile and difficult to reach environments
never dreamed possible before. Though ITI products can solve many remote-viewing problems, it is always best
to select the proper instrument for any given application. Only then can success be assured.
Your satisfaction is guaranteed with all products purchased from Instrument Technology, Inc. Feel free to contact
ITI or your local ITI Representative with any questions.
WARRANTY
Instrument Technology, Inc. warrants that the equipment is fit for the purposes described herein for a period of
one year after the date of shipment when used in accordance with the directions for use, and agrees to repair or
replace any such defective component part at no cost to the customer.
There are no other express or implied warranties. ITI's sole obligation and purchaser's exclusive remedy for
breach of any warranty shall be limited to repair or replacement of the product at the option of ITI. This warranty
does not cover, and ITI will not be liable for any resulting direct, proximate, incidental or consequential damages.
This warranty does not apply if the product has been subject to misuse, negligence, accident or improper
application, nor shall ITI be responsible for work done or repairs made by others.
PRODUCT SPECIFICATIONS
(1) 6.4” (NTSC) Monitor
(1) Battery Pack
(1) View-Shield Case
(1) 110VAC Battery Charger
Optional Accessories:
ITI Model # or P/N Description
P/N 119927 ITI 220VAC Battery Charger
P/N 119889 Spare Battery Pack
135314 6’ Telescopic Arm
OPERATING INSTRUCTIONS
OVERVIEW OF APPLICATIONS
ITI Model 126390 employs a unique visualization system intended for covert surveillance. It is a fully operational,
portable Monitor and Battery kit.
The optional 6’ long telescoping arm is structured to allow surveillance into limited access areas. The adjustable
camera head allows the user to view around corners and into crawl spaces to search for obstacles and/or
barriers.
CAUTION
MONITORS ARE DELICATE INSTRUMENTS, AND SHOULD BE TREATED ACCORDINGLY. PROPER
HANDLING AND CLEANING TECHNIQUES WILL GREATLY INCREASE THE LIFE OF THIS INSTRUMENT.
ONLY TRAINED OPERATORS SHOULD HANDLE THIS EQUIPMENT.
MONITOR SETUP
NOTICE
The Monitor has been disconnected from
Battery to preserve battery charge during
shipment.
See Monitor OM for instructions on
reconnecting Monitor & Battery.
Insert the free end of the four pin Video Cable into the four pin Video receptacle located on the rear of the
Monitor. Free end of cable has a quick-release lanyard. Pull lanyard for fast disconnects.
NOTE: Connector ends for Battery Charger and Video Cables are of different configurations, so unit
cannot be connected incorrectly.
At sides of Monitor/Battery Pack View-Shield Case, pull hook and loop tapes to release View Shield. Raise View
Shield to optimum viewing position and smooth hook and loop tapes to sides of Case to secure.
OPERATION
Video/Power on/off switch on the face controls the power to the Monitor. On a full charge the unit will operate for
approximately 15 hours when only Camera and Monitor are on. The power switch should remain in OFF position
when unit is not in use.
CHARGING BATTERY PACK
Align cable from Battery Charger with outlet on rear of Monitor. Push gently to connect. Plug into grounded
power outlet. A full charge will be achieved in approximately 6 –8 hours.
CHANGING OPTIONAL SPARE BATTERY PACK
Turn all power switches to OFF position. Fully unzip rear door of View-Shield Case. Loosen hook and loop cinch
strap that holds Battery Pack. Disconnect spent Battery Pack by pulling apart white plastic clips. Pull tab to
remove Battery Pack. Replace with fresh Battery Pack. Push white plastic clips together to reconnect. Fasten
hook and loop cinch strap to hold Battery Pack securely in case. Zip rear door closed.
ATTACHING OPTIONAL 6’ TELESCOPIC ARM
Insert the free end of the four pin Video Cable from handle end of Telescopic Pole into the four pin Video
receptacle located on the rear of the Monitor. Free end of cable has a quick-release lanyard. Pull lanyard for fast
disconnects.
NOTE: Connector ends for Battery Charger and Video Cables are of different diameters, so unit cannot be
connected incorrectly.
Swivel Lock lever near camera placement allows rotation of separately purchased Video Camera prior to
placement of camera in viewing position. After placement, rotate pole manually to reposition.
Twist Locking collars on Telescopic Arm left to unlock. Extend Telescopic Arm sections as needed. Twist
Locking Collars right to lock. Care should be taken to not over-extend short cables at camera end of assembly by
wrapping them too tightly around the Swivel Lock mechanism.
INSTRUMENT CARE
CLEANING AFTER USE
Wipe instrument after use with a soft, clean cloth. If instrument is soiled, use a non-abrasive, neutral detergent on
a damp cloth to clean it. Always store the instrument in its protective case.
NOTE: DO NOT IMMERSE INSTRUMENT IN LIQUID.
CLEANING OF OPTICS
Should cleaning of external surfaces be necessary, blow off dust with a triple-filtered, and high-pressure optical
quality dusting spray. Wipe surface with a clean cotton swab moistened with laboratory grade alcohol. Excess
alcohol can be blown away with the spray.
ITI Model 126110 RVI Cleaning Kit may be used.
PRECAUTIONS
Do not use beyond recommended temperatures:
Maximum 150° F (65° C)
Minimum 32° F (0° C)
Do not allow instrument to contact live or exposed wiring. It is an excellent conductor.
REPAIR POLICY
If your equipment requires factory attention, contact ITI’s Customer Service Dept. at (413) 562-3606 for a Return
Authorization Number. Please be prepared to furnish your model and serial numbers. Return the equipment to
ITI, freight prepaid.
Ship to: Instrument Technology, Inc.
33 Airport Road
Westfield, MA 01085-1357
Please note Return Authorization Number on Purchase Orders, and all shipping documents.
Upon receipt of your equipment, ITI will assess its condition to determine if repairs are needed. If repairs are
required, we will quote repair costs and a schedule for repairs. Your options at this point are:
1) Accept Repair
To proceed with the repair, ITI will require a purchase order for the full quoted repair price.
2) Decline Repair -Upgrade to a New Instrument
Choosing this option requires a purchase order for the new equipment at its quoted price. ITI will ship out the
next available unit.
3) Decline Repair
Please Note -Most repair evaluations require a partial or complete disassembly of the equipment. Once
disassembled, it is impossible to return it to the customer in “as received” condition. At the
customer's option, ITI will either return your equipment in its disassembled state, or dispose of it.
Table of contents
