ITRON OpenWay Riva CAM3 Series User manual

OpenWay® Riva CAM3S
and CAM3M Installation
Guide
INSTALLATION GUIDE
02 March 2020
knowledge to shape your future

OpenWay® Riva CAM3S and CAM3M Installation Guide
02 March 2020
815-0080-00
Copyright © 2020 Itron, Inc. All rights reserved.
Confidentiality Notice
Confidential Information of Itron®, Inc., provided under nondisclosure obligations. The information
contained herein is proprietary and confidential and is being provided subject to the condition that (i) it be
held in confidence except to the extent required otherwise by law and (ii) it will be used only for the
purposes described herein. Any third party that is given access to this information shall be similarly bound
in writing.
Trademark Notice
Itron is a registered trademark of Itron, Inc.
All other product names and logos in this documentation are used for identification purposes only and may
be trademarks or registered trademarks of their respective companies.
For more information about Itron or Itron products, go to www.itron.com.
If you have questions or comments about a software or hardware product, contact Itron Technical Support
Services.
Contact
Email: [e-mail]
Itron Access: https://access.itron.com
Telephone Itron Technical Support North America: 1-877-487-6602
For technical support contact information by region, go to www.itron.com and select your country and
language.
02 March 2020 815-0080-00 Itron, Inc. Page 2 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide

Table of Contents
Ope n Way ® Riva CAM3 Sa n d C AM3 MIns tallation Gu ide 1
Ta b leo fCon tents 3
New inthis Do c u me n t 6
1 About This Guide 7
CGR IOS Compatibility 7
Guide Conventions 8
Related Product Documentation 8
Regulatory Compliance 9
Labeling for USA and Canada 9
FCC Compliance 10
USA FCC Part 15, Class B 10
Canada ISED (Innovation, Science and Economic Development) Compliance 10
RF Exposure (FCC/ISED) 11
Professional Installation 12
Modification and Repairs 12
Electromagnetic Compatibility 12
2 Introduction 13
CAM3S/CAM3M Overview 13
OpenWay® Riva Communication System Overview 15
3 Installation Kits 17
CAM3S/CAM3M Installation Kit 17
Lightning Arrestor Kit 17
RF Filter Kit 17
Coaxial Cable Kit 18
Antennas and Antenna Kits 18
Antenna Supported Specifications 18
915MHz 5.5dBi Remote Antenna Kit 19
915MHz 5.15dBi Remote Antenna Kit 20
915MHz 8.15dBi High Gain Remote Antenna Kit 21
4 Star and Mesh Deployment Installation 22
Requirements and Materials 22
Order of Installation 23
02 March 2020 815-0080-00 Itron, Inc. Page 3 of 102

Disconnecting Power to the CGR 23
Removing the CGR from the Pole 27
Installing the CAM3S/CAM3M 29
Reinstalling the CGR Back on the Pole 32
Installing the Remote Antenna 35
Placement Guidelines for Remote Antenna 35
Remote Antenna Connections & the Lightning Arrestor 36
Assembling and Attaching the Antenna 38
Assembling the Remote Antenna 38
Attaching the Remote Antenna to the CGR Mounting Bracket 41
Weatherproofing the RF Connections 42
Reinstalling the Power and Ground to the CGR 45
5 Radio Frequency and Power Line Carrier Installation 50
Disconnecting Power to the CGR 50
Installing the CAM3S/CAM3M Using the PLC Signal Cable 54
6 ACT Coupler Unit Installation (CAM3M Only) 60
Adaptive Communication Technology (ACT) Coupler Unit Function 60
Removing the CGR from the Pole 60
Reinstalling the CGR 64
Installing the ACT Coupler Unit 65
7 Replacing an Existing CAM with a New CAM3S/CAM3M in the Field 71
Requirements and Materials 71
Removing an Existing CAM 72
Installing the New CAM3S/CAM3M 80
Changing the IPv6 Prefix Address of the CGR 85
Updating the Data Rate 88
A Specifications 89
B RF Filter Installation 91
Placement Guidelines for Remote Antenna 92
Connecting a RF Filter 93
Australia Applications 94
02 March 2020 815-0080-00 Itron, Inc. Page 4 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide Table of Contents

Glossary 96
Index 100
02 March 2020 815-0080-00 Itron, Inc. Page 5 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide Table of Contents

New in this Document
Table shows the revision history for this guide, providing a description of the changes.
Revision Date Description
815-0080-00 27 February
2020
■New document.
Table 1Document Revision History
02 March 2020 815-0080-00 Itron, Inc. Page 6 of 102

1
About This Guide
This guide provides the steps to install two CAM3x devices: the CAM3S and the CAM3M. The
major difference between them is the CAM3S is for a Star deployment and the CAM3M is for a
Mesh deployment.
■CAM3S - The Connected Grid Router (CGR) Adaptive Communications Technology (ACT)
Module version 3 for a Star network deployment, or CAM3S installs into the Cisco®
Connected Grid Router (CGR) model 1240. The CAM3S is for Star deployments and uses
the remote antenna.
■CAM3M - The Connected Grid Router (CGR) Adaptive Communications Technology (ACT)
Module version 3 for a Mesh network deployment, or CAM3M installs into the Cisco®
Connected Grid Router (CGR) model 1240. The CAM3M is for Mesh deployments and uses
the WPAN antenna.
Additionally, the guide provides information about: Star and Mesh deployment installation, Radio
Frequency (RF) and Power Line Communications (PLC) installation, ACT Coupler Unit
installation, replacing an existing CAM with a new CAM3S/CAM3M in the field and RF Filter
installation.
This guide is designed for field installers who are familiar with the CGR, its function, and its
operation.
For further information about the base CGR installation, refer to the Cisco 1240 Connected Grid
Router Hardware Installation Guide.
The guide is divided into the following topics:
■Introduction
■Installation Kits
■Star and Mesh Deployment Installation
■Radio Frequency and Power Line Carrier Installation
■ACT Coupler Unit Installation (CAM3M Only)
■Replacing an Existing CAM with a New CAM3S/CAM3M in the Field
■RF Filter Installation
CGR IOS Compatibility
Ensure you are running the correct IOS version on your CGR.
02 March 2020 815-0080-00 Itron, Inc. Page 7 of 102

Important! For new installations, or for a Star deployment running IOS v15.6.3m1,
on your CGR you must upgrade to IOS v15.8.3m1. However, for existing Mesh
deployments, no IOS upgrade is required.
For detailed information about how to upgrade your IOS version, See CGR IOS Upgrade Guide,
(815-0001-xx).
Guide Conventions
The following visual elements are used throughout this guide, when applicable.
Warning! This icon and text indicates hazardous situation, which if not avoided, could
result in death or injury.
Caution: This icon and text indicates a potentially dangerous procedure. Instructions
contained in the warning must be followed. Failure to do so may result in damage to
the device.
Important! This icon and text indicates important things the user should pay attention
to.
Note: This icon and text designates information of a special note.
Tip: This icon and text indicates information to make things easier to use.
Related Product Documentation
Document Name Software
Version
Part Number Link
CGR IOS Upgrade Guide v15.5 or later 815-0001-xx N/A
Cisco 1240 Connected Grid
Router Hardware Installation
Guide
N/A N/A Cisco 1240 Connected Grid Router
Hardware Installation Guide
Table 2Product Related Documentation
02 March 2020 815-0080-00 Itron, Inc. Page 8 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 1 About This Guide

Document Name Software
Version
Part Number Link
Cisco CGR1000 IOx Application
Development Cook Book
N/A N/A Cisco CGR1000 IOx Application
Development Cook Book
OpenWay Riva System Upgrade
Guide GSR 5.0
GSR 5.0 TDC-8011-xx N/A
Note: The last two or three numbers of the document part number denote the revision number and are subject to
change without notice.
Table 2Product Related Documentation (continued)
Regulatory Compliance
Labeling for USA and Canada
The following information appears on labels on the exterior of the CGR and only applies to
FCC/ISED models:
■FCC ID: LDKALTMT0556
■IC: 2461B-ALTMT0556
■Model: CGR 1240
Contains (for the CGR):
■FCC ID: N7NMC7355
■IC: 2417C-MC7355
■Model: MC7355
or,
■FCC ID: N7NMC7455
■IC: 2417C-MC7455
■Model: MC7455
Note: The FCC ID, IC and Model numbers vary depending on the Cisco CGR unit.
Contains (for the CAM3):
■FCC ID: EO9OW3
■IC: 864A-OW3
■Model: OW3
■Model Name: CAM3
The following information may also appear on an exterior label:
02 March 2020 815-0080-00 Itron, Inc. Page 9 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 1 About This Guide

"This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation."
FCC Compliance
This device complies with Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. Operation is
subject to the following two conditions:
■This device may not cause harmful interference.
■This device must accept any interference that may cause undesirable operation.
This device must be installed to provide a separation distance of at least 20 centimeters (7.9
inches) from all persons to be compliant with regulatory RF exposure.
USA FCC Part 15, Class B
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
■Reorient or relocate the receiving antenna.
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
■Consult the dealer or an experienced radio/TV technician for help.
Caution: To ensure system performance, this device and antenna shall not be
changed or modified without the express approval of Itron. Per FCC rules,
unapproved modifications or operation beyond or in conflict with these instructions for
use could void the user's authority to operate the equipment.
Canada ISED (Innovation, Science and Economic Development) Compliance
This device contains license-exempt transmitter(s)receiver(s) that comply with Innovation,
Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to
the following two conditions:
02 March 2020 815-0080-00 Itron, Inc. Page 10 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 1 About This Guide

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage; et
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Under Innovation, Science and Economic Development Canada regulations, this radio
transmitter may only operate using a antenna of a type and maximum (or lesser) gain approved
for the transmitter by Innovation, Science and Economic Development Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique
à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à
l'établissement d'une communication satisfaisante.
The radio transmitter (IC: 864A-OW3) has been approved by Innovation, Science and Economic
Development Canada (ISED) to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 864A-OW3) est conforme aux CNR d'Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessus et ayant un gain admissible maximal
et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette
liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
RF Exposure (FCC/ISED)
This equipment complies with radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between this
device’s radiators and your body. These transmitters must not be co-located or operating in
conjunction with any other antennas or transmitters, that are not part of the CGR Host router and
CAM3 module.
02 March 2020 815-0080-00 Itron, Inc. Page 11 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 1 About This Guide

Cet équipement est conforme aux limites d'exposition aux radiations définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimale
de 20 cm entre les radiateurs de l'appareil et votre corps. d’autres antennes ou émetteurs ne
faisant pas partie du routeur hôte CGR et du module CAM3.
Professional Installation
These antennas are intended for professional installation by the integrator. The OEM integrator
is still responsible for the FCC compliance requirement of the end product, which integrates this
antenna.
Caution: If Ethernet is used, the cable length must not exceed two meters in total.
Lengths longer than two meters are not approved and do not meet FCC and ISED
compliance requirements.
Modification and Repairs
To ensure FCC compliance and system performance, this device, antenna and/or coaxial
assembly shall not be changed or modified without the express written approval of Itron. Any
unauthorized modification will void the user’s authority to operate the equipment.
Warning! This device contains no user serviceable parts. Attempts to repair this
device by unauthorized personnel may subject the person to shock hazard if removal
of protected covers is attempted. Unauthorized repair voids the warranty and/or
maintenance contract with your company.
Electromagnetic Compatibility
Caution: Use only approved accessories with this equipment. All cables must be high
quality, shielded, and correctly terminated. Unapproved modifications or operation
beyond or in conflict with these use instructions may void the authority's authorization
to operate the equipment.
02 March 2020 815-0080-00 Itron, Inc. Page 12 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 1 About This Guide

2
Introduction
This chapter covers the following topics:
■CAM3S/CAM3M Overview
■OpenWay® Riva Communication System Overview
CAM3S/CAM3M Overview
This section provides information about the modules. In general, the CAM3S/CAM3M provides
connectivity to supported devices, like Electricity Meters, and Battery Powered Devices, on the
Itron OpenWay® Riva Communication system when installed into a CGR. See OpenWay®
Riva Communication System Overview .
The CGR ACT Module (CAM) resides inside the Cisco®CGR and acts as the root-node within
the network, routing packets and information from meters or grid devices between the Adaptive
Communication Technology (ACT) network and the headend (OWOC-CM). The
CAM3S/CAM3M supports adaptive communications, that allows meters and grid devices to
interact with each other while dynamically switching between Radio Frequency (RF) and Power
Line Carrier (PLC) to ensure the fastest and most reliable path.
In addition to the module residing in the CGR. The CGR contains two operating systems: a
Cisco®Internetwork Operating system (IOS) and a Cisco®Guest Operating System (GOS).
The IOS runs on the CGR and enables data communications between network nodes. The GOS
runs on the CGR and provides a virtual connectivity. The IOS forwards traffic from GOS through
regular IPforwarding mechanisms. Furthermore, the ACTD firmware runs on the CGR. The
ACTD firmware servers as a communication gateway between the CGR's operating system
(IOS) and the CAM3S/CAM3M. Also, the CAM3S/CAM3M also contains its own firmware. The
CAM3S/CAM3M firmware provides communication to the smart meters. When the CGR is
deployed in a star configuration with Battery Powered Device (BPD), a remote antenna is
required to ensure optimal radio performance. See figure.
02 March 2020 815-0080-00 Itron, Inc. Page 13 of 102

Figure 3CAM3S/CAM3M Functionality
The CAM3S/CAM3M's physical features include: a RF QMA Connector, and a 6-Pin Power
Line Carrier (PLC) Signal Cable Connector among others. See figure.
02 March 2020 815-0080-00 Itron, Inc. Page 14 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 2 Introduction

Figure 4CAM3S/CAM3M Major Parts Front View Photo
Reference
Number
Item Details
1 Radio Frequency
(RF) QMA
Connector
Provides a connection for the Radio Frequency (RF) Antenna Cable. For use
with either a Wireless Personal Area Network (WPAN) antenna or a remote
antenna based on your application needs.
2 6-Pin Power Line
Carrier (PLC)
Signal Connector
Provides a connection for the PLC Signal Cable.
3 Handle(s) Helps in inserting and removing the module from the CGR. And used to tie down
cable using plastic tie wraps.
4 Retaining Screw
(s) Phillips
Secures the module into the slot of the Connected Grid Router (CGR).
Table 5CAM3S/CAM3M Major Parts
OpenWay®Riva Communication System Overview
The communication system features an innovative multimedia IPv6 network that uses both
Radio Frequency (RF) and Power Line Carrier (PLC) links within a mesh to route messages and
data between standards-based smart meters Device Language Message
Specification/Companion Specification for Energy Metering (DLMS/COSEM) and the headend
system.
02 March 2020 815-0080-00 Itron, Inc. Page 15 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 2 Introduction

The communication module enables utilities to deploy the network without specifically planning
for segregation of RF and PLC environments. Intelligence in the communication module
chooses the communication link quality and modulation scheme that support the best possible
data rate. Data rates of up to 600Kbps are achievable by this multimedia mesh. This is done
automatically in real-time by the modules without any need for pre- programming or path hard-
coding. The communication modules create their own multi-hop environment using the best
available physical path for communication where the routing is managed by standardized
Internet Engineering Task Force (IETF) routing protocols that are independent of the physical
link. See figure.
Figure 6OpenWay Riva Communication Solution Network
02 March 2020 815-0080-00 Itron, Inc. Page 16 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 2 Introduction

3
Installation Kits
This chapter covers the following topics:
■CAM3S/CAM3M Installation Kit
■Lightning Arrestor Kit
■RF Filter Kit
■Coaxial Cable Kit
■Antennas and Antenna Kits
Note: In accordance with FCC rules, unapproved modifications or operation beyond or in
conflict with these use instructions could void the user's authority to operate the equipment.
Unauthorized access or modifications to the CGR voids the warranty.
Note: Not all kits are required for all installations.
CAM3S/CAM3M Installation Kit
The following items are included in the CAM3S/CAM3M installation kit (K574319-005):
■One (1) CGR ACT Module 3 (CAM3S/CAM3M)
■One (1) Regulatory label
Lightning Arrestor Kit
This kit contains the following item:
■One (1) lightning arrestor (MSE-0417-002-R)
Note: This is an optional kit that is required when connecting the CAM to an
external antenna via Coaxial cable.
RF Filter Kit
The following items are included in the RF Filter installation kit (KIT-9036-001):
■Mounting bracket
■CGR to RF Filter cable
■RF Filter
■Lightning arrestor
02 March 2020 815-0080-00 Itron, Inc. Page 17 of 102

Note: This kit is optional. This kit is required for Star deployments using CAM1
and for Star/Mesh deployments in Australia using CAM1, or CAM3. Mesh and
Star deployments outside of Australia do not require the RF Filter. The filter can
be removed when upgrading CAM1 Star deployments to CAM3S (outside of
Australia).
Coaxial Cable Kit
The following items are included in the coaxial cable kit (KIT-9033-001):
■One (1) coaxial cable (5 meters in length)
Antennas and Antenna Kits
Each CGR/CAM3 installation requires one of the supported antennas for proper operation. The
CGR/CAM3 has been designed and approved per FCC and ISED rules to operate with these
antennas.
Caution: Antennas not approved by Itron are strictly prohibited for use with this
device. Installing the CAM3 with an unapproved antenna voids the product warranty
and can void the user's authority to operate this equipment. This section describes the
following approved antenna kits:
■915MHz 5.15dBi (KIT-0049-001)
■915MHz 5.5dBi (KIT-0073-001)
■915MHz 8.15dBi (KIT-0018-007)
■915MHz 2.8dBi (ANT-MP2-I-OUT-M)
Antenna Supported Specifications
This table provides the specifications for the supported 915MHz antennas. The CAM3 is
designed to operate with the antennas listed here. Antennas not listed here are strictly prohibited
for use with the CAM3. The required antenna impedance is 50Ω.
Specification Itron Part Number
KIT-0049-001
Itron Part Number
KIT-0073-001
Itron Part Number
KIT-0018-007
Cisco ANT-MP2-I-
OUT-M
Default Network Star Star Star Mesh
Frequency range 902-928 MHz 902–928 MHz 902–928 MHz 698–960 MHz
Maximum gain 5.15dBi 5.5dBi 8.15dBi 2.8dBi
Horizontal
Beamwidth
Omnidirectional Omnidirectional Omnidirectional Omnidirectional
Table 7Supported 915MHz Antenna Specifications
02 March 2020 815-0080-00 Itron, Inc. Page 18 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 3 Installation Kits

Specification Itron Part Number
KIT-0049-001
Itron Part Number
KIT-0073-001
Itron Part Number
KIT-0018-007
Cisco ANT-MP2-I-
OUT-M
Impedance 50 Ohms 50 Ohms 50 Ohms 50 Ohms
Termination Type N Male Type N Male Type N Male MCX jack
Overall length 18.8" 18.8" 65" 3.04”
Radome diameter 1" OD 1" OD 1.31" OD 1.61" OD
Power rating 50W 50W 100W 10W
Lightning protection Direct ground Direct ground Direct ground n/a
Mounting arm
length
n/a n/a ~8 in. Direct mounted
Weight (w/o
clamps)
1 lb. 0.7 lbs. 3 lbs. 0.2 lbs.
Maximum wind
speed
160 mph 160 mph 125 mph 165 mph
Wind load @ rated
wind speed
n/a n/a 57 lbs. n/a
Table 7Supported 915MHz Antenna Specifications (continued)
Note: To reduce potential radio interference to other users, select an antenna type with gain
such that the Equivalent Isotropically Radiated Power (EIRP) is not more than permitted by
the regulatory rules of the country where installed.
Note: The 8.15dBi antenna kit (KIT-0018-007) comes with a lightning arrestor that is for
other types of installations and is optional. The lightning arrestor that is included with the RF
Filter kit (KIT-9036-001) is the correct arrestor for this application.
915MHz 5.5dBi Remote Antenna Kit
The following items are included in the Remote Antenna installation kit (KIT-0073-001):
■915MHz 5.5dBi gain antenna
■Antenna mounting kit:
Remote-mount adapter
Antenna holder
Mounting bracket
6-inch bolts (4)
1¾-inch bolts (2)
02 March 2020 815-0080-00 Itron, Inc. Page 19 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 3 Installation Kits

Flat washers (6)
Split washers (6)
Nuts (6)
Pipe clamp hangers (2)
Silicone seal
Anti-seize lubricant
Caution: Do not install a 5.5dBi antenna directly on the CGR/CAM3. Antenna
installation directly on the CGR/CAM3 compromises mechanical integrity and will not
meet the compliance requirements.
915MHz 5.15dBi Remote Antenna Kit
The following items are included in the Remote Antenna installation kit (KIT-0049-001):
■915 MHz 5.15dBi gain antenna
■Antenna mounting kit:
Remote-mount adapter
Antenna holder
Mounting bracket
6-inch bolts (4)
1¾-inch bolts (2)
Flat washers (6)
Split washers (6)
Nuts (6)
Pipe clamp hangers (2)
Silicone seal
Anti-seize lubricant
Caution: Do not install a 5.5dBi antenna directly on the CGR/CAM3. Antenna
installation directly on the CGR/CAM3 compromises mechanical integrity and will not
meet the compliance requirements.
02 March 2020 815-0080-00 Itron, Inc. Page 20 of 102
OpenWay® Riva CAM3S and CAM3M Installation Guide 3 Installation Kits